Globus New Media ECO Spot LED40C User manual

ECO Spot LED40C User Manual
Thank you for choosing an ECO Spot™ Gobo projector.
Please read this manual before installing or operating this fixture,
follow the safety precautions listed below and observe all warnings.
Below is a general Gobo Changer description, please see the separate ECO Spot
Gobo Changer Manual for Details
WARNING!
Some models are equipped with a voltage selector switch on the back plate of the
unit. Select the correct Line Voltage before Operating.
Package Contents

Projector with power cord

Test Gobo
Safety Information
Electrical Safety
ECO Spot™ LED40C User Manual
•Place your fixture at a suitable place with good air flow.
•Keep flammable materials away from the fixture.
•Minimum distance to flammable material = 1 ft (0.3m).
•Provide a minimum clearance of 4 in (10cm) around air vents.
•Use only genuine spare parts for part replacement.
•Do not look directly into the lamp; it can result in eye damage.
•Always unplug the unit from the power mains before any service is done.
•Light fixtures should be installed and maintained only by qualified personnel with
experience in lighting equipment and general electrical experience.
•Disconnect the fixture from AC power before handling the fixture.
•Always ground (earth) the fixture electrically.
•Use only a power source
that complies with local building and electrical codes and
has both, overload and ground-fault protection.
•Do not use the fixture if the power cable or power plug is in any way damaged,
defective or wet, or if they show signs of overheating.
Copyright © 2014 Globus New Media LLC Page 1

ECO Spot LED40C User Manual
Handling Instructions
•Before the initial start-up, please unpack and carefully check for damage caused
during transportation.
•Place your fixture at a suitable place with good air flow.
•Make sure there are no flammable materials close to the lamp.
Warranty
One Year from Date of Purchase. Keep your receipt for reference and contact your dealer
in case of warranty issues.
Projection Lenses
The projector accommodates interchangeable projection lenses to allow optimizing the
projection size and resulting brightness at varying distances. The more narrow the lens,
the smaller and brighter the image will be at a given distance.
Focusing
Multi-functional Yoke
•
When suspending the fixture above ground level, verify that the structure
can hold
at least 10 times the weight of all installed devices.
•Verify that all external covers and rigging hardware are securely fastened and use
an approved means of secondary attachment such as a safety cable.
•Power up the projector by pressing the power switch in the back.
•Focus the projection by twisting the lens in and out until
the image is well focused.
When used for the first time, the lens will often need to be twisted outwards many
rotations to reach the focusing point.
•Turn on the gobo rotator with the push-button in the back and switch it off when
the gobo projects in the desired position.
•Re-adjust the focus if necessary.
•The yoke can slide over the whole length of the fixture body to accommodate a
wide range of pointing directions.
•The yoke serves as stand.
•The yoke can be screwed to a wall or ceiling or fastened with a C-clamp
Page 2 Copyright © 2014 Globus New Media LLC

ECO Spot LED40C User Manual
Gobo Changer Functionality (see the Gobo Changer Manual for details)
The gobo changer has four gobo slots. A timer continuously switches between the
different gobos. Unless customized (see below), it will go a full sequence ( slot
1,2,3,4,1,2,…). Turn on and off the gobo changer with the small switch on the back plate.
Interval Timer: The interval timer can be set by turning the knob on the back plate from
continuous up to approx. 120 seconds changing interval.
Single Gobo: For showing only a single gobo w/o any changes, simply turn off the
changer power switch on the back plate when the correct gobo shows.
Two or Three Gobos: For showing 2 or 3 gobos only. The changer is equipped with four
sensor magnets, one for each gobo slot. For showing only three gobos, remove one
magnet. For two gobos, remove two
magnets. Unscrew the magnet with pliers.
Tip: Screw the removed magnet back in
from the opposite to keep it for later use.
Static Slot: The unit has an additional
static slot, which can be used in two
ways:
•Color Overlay in conjunction
with b/w gobos in the changers
Gobo Wheel and a color filter in the
Static Slot.
•Gobo Color Changer
in conjunction a b/w gobo in the Static Slot and color filters
in the changers Gobo Wheel.
Copyright © 2014 Globus New Media LLC Page 3

ECO Spot LED40C User Manual
Line Voltage
If your model is equipped with a Line
Voltage Selector in the back, select the
correct line voltage:
US Setting (120V)
90-130V, 50/60Hz, 0.4A, 48W
International Setting (220V)
90-240V, 50/50Hz, 0.4A, 48W
If no Line Voltage Selector is present
your model is autosensing:
90-240V, 50/60Hz, 0.4A, 48W
Ambient Operating Temperature
-13 to 104°F (-25 to 40°C)
Dimensions / Weight
Body without yoke:
10in x 5.25in (254mm x 133mm) (L x D)
The projection lens adds 0.5 to 2in (12 to
50mm) to the length.
Yoke Height:6in (127mm)
Weight 8lbs (3.6kg)
Gobo Dimensions
This changer takes E-Size Metal or Glass
Gobos and Dichroic filters.
Outer Diameter (OD): 37.5mm
Max. Image Diameter (ID): 25mm
Max Thickness: 4mm
LED Lamp
Lens Options
The projector can be equipped with
standard ECO Spot projection lenses.
A larger focal length (f) makes a smaller
projection angle and therefore a smaller
but brighter image. Currently these
lenses are available:
•Power: 40W
•Rated Bulb life 50,000h
•Color Temp. 5,500k, +/-500k
•Rated luminous flux: 2,000lm
•Effective luminous flux: 1100lm
•Wide f=50mm, 25º
•Medium f=70mm, 20º
•Semi-Narrow f=100mm, 15º
•Narrow f=140mm, 10º
Page 4 Copyright © 2014 Globus New Media LLC