Glue Machinery G25E03-001 User manual

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
ChampStickTM 400
High Production - Heavy Duty - Industrial
½″Hot Melt Stick Gun
Manual
Part # G25E03-001
Specification: AC 120V - 400W Glue Stick size: 7/16″x 11 ¾″
G25A77-002- clear glue stick is general purpose adhesive is for assembly and packaging
G25A77-003 –yellow glue stick adhesive is for aggressive bonding in packaging and product
assembly. READ SAFETY RULES AND INSTRUCTIONS CAREFULLY!
WARNING:
-When using this hot melt glue gun, always follow basic safety precautions. This will reduce the possibility of accidental injury
due to burns or electrical shock.
-Always wear safety glasses, protective gloves, and protective clothing with long sleeve shirts and pants. This product must
have a ground connection.

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
Read all Safety Instructions:
Never use the tool if it is damaged in any way.
Do not attempt to remove unused portion of a glue stick from the tool.
Never immerse glue gun in water or other liquids for any reason.
Allow the gun to air cool only.
Use ONLY the correct size glue stick or Damage will occur to the gun
Work area. This tool is designed to be used on a clean, dry work surface. Excessive dust and dirt
may impair the operation of this tool. Do not use in wet or damp locations.
This tool is recommended for indoor use only. Do not use outdoors.
Glue gun storage. After use, allow glue gun to cool completely prior to storage. When not in
use, the glue gun should be stored in dry location.
Electrical cord precautions. Do not carry the tool by the cord or pull to disconnect from the
receptacle. Keep the cord away from the nozzle or other high heat sources. Periodically inspect the
electrical cord for any sign of wear or damage.
Disconnect electrical power. When not using and before servicing. Do not pull on cord to
unplug from electrical receptacle.
Be cautious. Pay attention to your work. Beware of any molten hot glue on your substrates. Do
not operate under the influence of alcohol or other drugs that may impair your physical abilities.
Do not touch the heated nozzle of the glue gun or the hot adhesive. The operating
temperature of this tool can be as high as 446°F.
Use recommended accessories. Use only recommended accessories and adhesives in this glue
gun. Using the wrong adhesive or accessory may result in accidental injury and permanent damage
to the glue gun.
Hot melt adhesives are never a replacement for structural fastener.
Hot melt glue should not be used for projects that will be exposed to extreme
heat or cold. Some adhesive used with this glue gun can start softening at about 140°F.
Do not expose the glue gun to extreme changes in temperature during or directly
after use.
Do not leave the glue gun unattended while plugged in or in a hot condition.
Make sure to have sufficient eye protective wear.

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
Operation:
1. Plug the glue gun into any 110/120 AC outlet; When power switch is “On”, the switch will be red and
pushed down into the tool.
* Insert an adhesive glue stick (7/16″) into the back of the tool. Allow the tool to heat for 10 to 15 minutes
before using.
2. WARNING: Never pull sticks out of the back of the gun once inserted.
3. When the gun is fully heated, squeeze the trigger slowly until the melted material begins to flow from the
nozzle. Release the trigger to stop the glue flow.
4. The output volume per trigger stroke can be adjusted by the stroke adjustment screw. This can be found at
the back of the glue gun just below the glue stick.
5. Different nozzle tips are available for different gluing applications and output amount.
6. Use the included screwdriver to adjust the tool to the designated temperature of the gun. ( 284oF to 428oF)
Tips
The following guide provides helpful information for G25E03-001/CHAMP STICKTM 400 glue gun and
hot melt adhesives.
1. The limited open time of the hot-melt is (30) seconds and depends on a number of factors. After
the adhesive has been extruded onto the substrate, the part should be pressed together quickly.
The bond will occur as the adhesive losses temperature
2. The open time of the hot-melt can be extended by the ambient temperature and the increased
quantity of the glue.
3. Large substrates can present a challenge due to the extended time to apply the glue and the
quantity of glue need on the substrate. The adhesive can harden before you have extruded the
required amount. Using a higher volume hot melt system from Glue Machinery Corporation such
as the Champ 3, 600, 10 or Economelt can improve output, compression and resulting bond.
4. Preheating the substrate surface prior to application and compression will improve the bonding
strength. * Testing the adhesive for open time and set time can provide valuable test results.
5. Hot/melt adheres well to porous surfaces like foam, paper, cloth, particleboard, and wood.
6. Hot/melt adhesives quick set time eliminates the need for clamps or other holding devices.
7. Hot-melt can begin to soften when the substrate temperature exceeds 140ºF and should not be
used for items that will be subjected to temperatures above that. Other hot melts are available
with higher softening points that must be processed with bulk Hot Melt Systems available at
Glue Machinery Corporation.
8. Hot/melt adhesives can be used in place of nails, staples, tape, or liquid glue: however, they
should not be used to replace structural fasteners where heavy loads are involved.
9. Glue can string from the nozzle. Adjustments to the temperature and nozzle application methods
can help reduce stringing. Glue strings can also be reduced with higher temperature and smaller
nozzle .
Save these safety rules for future use:
1. It is normal for the Champ Stick TM 400 to become very warm during use. The nozzle is very HOT. USE
CAUTION:
2. The glue gun should be turned off and unplugged after use or if it will not be used within 1-hour
period. The adhesive can be stored indefinitely in the unheated gun and re-melted by heating up
the tool .Heat the glue gun for at least 10 minutes.
3. Some substrates are heat-sensitive and can be damaged by the hot nozzle or even the hot glue.
Whenever possible, test a piece of scrap material or a hidden portion of the object being repaired.
4. If any part of the tool is damaged, stop work, turn off glue gun and repair.
5. If the operator accidentally contacts the hot glue gun, immediately cool the affected area.
6. Then seek medical assistance.

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
.
Specifications:
Connection 120VAC=3.3 amp/1ph/50-60Hz.
Heating capacity 400W
Temperature control Adjustable thermostat
Approximate Heat-up time Approx. 10-15 min
Adjustable thermostat control (284oF- 446oF)
Weight: Champ Stick 400 1.8 lbs
Cord Weight/length: .6 lbs. / 7.6in cord length
Glue Stick Weight: 1 ounce (7/16″x 11 ¾″)
Melt extruded with full trigger pull 0.038801oz
Measurements of glue gun Length 12″x width 9″

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
Preventive Maintenance
1. To prevent the clogging of the glue gun, keep the feed mechanism and melt chamber free from
dirt and other foreign debris. Store unused glue sticks in a clean environment.
2. Do not pull glue stick from the back of the glue gun. The feed mechanism may be damaged or
impaired. If you desire to change types of glue, cut off the protruding end and push the remainder
through with the new type of glue.
3. Do not lay heated gun on its side. Keep the heated gun in an upright position with nozzle pointed
down.
4. If melted glue has escaped from the melt chamber entrance and is interfering with the feed
mechanism; allow gun to cool, and gently remove the obstructing glue.
5. Replace the nozzle if glue drips excessively. Do not attempt to change nozzle when glue is cold.
To change, the gun must be heated until the glue is softened enough to remove nozzle. Use
gloves with the proper wrench to remove the old nozzle. (USE CAUTION) Install the new
adapter G25E01-003 and a new nozzle G25E01-004. Tighten only until snug. Do not over
tighten.
6. Keep outside of glue gun clean.
7. Only use approved 7/16″diameter stick glue with this gun.
Champ Stick TM 400 Features
Glue stick direction
Stroke adjustor
Power Cord (120v)
ON/OFF switch
Trigger
Temperature adjustor

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
CHAMP STICKTM 400 features:
400 watts of power. high glue melt rate
Durable light weight ergonomic handle
Easy pull 4 finger trigger, with ergonomic handle. Stroke adjustor allows user to pre-set the output of
glue per trigger pull.
Use of screwdriver for adjusting the temperature of glue gun between (284ºF-446ºF).
Gun is set at factory to 374ºF approximately.
Screw driver can be stored easily at the base of the glue gun.
Spare and replacement parts available at:
Glue Machinery.com
ChampStickTM 400 Yellow and ClearAdhesive
G25A77-002
Clear general purpose adhesive for packaging and product assembly.
G25A77-003
Yellow colored adhesive stick often used for packaging and product assembly.
Minimum
orders
The number of sticks per pound is 15.5. Minimum order is 15 lbs.
Glue Stick
Diameter/length
7/16″x 11 3/4″Diameter Glue Sticks
Stroke adjustor
Easy pull trigger
ON/OFF
switch
Ergonomic
handle
Screw driver storage
Temp. Control
TPR 手柄

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
Standard and Additional nozzle parts
G25E01-003-Adapter- Nozzle connection (.157″) (Standard)
G25E01-004- Nozzle- (.118″) Metal Nozzle Tip (Standard)
G25E01-011- Nozzle- (.790″) Metal Nozzle Tip
G25E01-002- Nozzle- (.118″) (rubber)
G25E01-005- Extension Nozzle, ( 1.25″) Length Tip, Single Orifice, (.790″)
G25E01-006- Extension Nozzle, ( 1.25″) Length Tip, Single Orifice (.118″)
G25E01-008- T Nozzle, 4 Orifice, (.0395″) Orifice size, (.157″) CTRS, Nozzle overall
width (.7480″)
G25E01-007- T Nozzle, 2 Orifice,(.118″) Orifice Size(.3935″) CTRS, Nozzle overall width
(.7480″)
G25E01-009-T Nozzle, 3 Orifice,(.595″) Orifice Size(.512″) CTRS, Nozzle overall width
(1.77″)

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
CAMPSTICK TM 400 Schematic Diagrams
No.
Name
Part No.
1-4
Handle Set
G25E35-001
11
Trigger Set
G25E76-001
12
Heater Set
G25E50-001

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
Internal Components Schematic
Number 9 in the schematic shows
the power cord. The photo to the left
shows the new power cord strain
relief spring. Number 9* in the chart
and Part number G25E42-001.

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
No.
Name
Part Number
8
On/off Switch
G25E74-001
9
9*
Power Cord
Strain relief spring
G25E93-001
G25E42-001
10
Fuse
G25E87-001
11
Thermostat Set
G25E97-001
13
Inlet Tube Set
G25E47-001
*16
Metal Nozzle
G25E01-004
*17
Adapter
G25E01-003
*Note: these parts have replaced the G25E01-002 rubber nozzle in the schematic.
* Note: 9* is a new part for the glue gun G25E42-001.
Examples 1, 2, and 3 show
you how to install the
power cord strain relief
spring provided in the
contents of the box. Part
Number is G25E42-001.
This photo to the left shows the
finished example of the power cord
strain relief spring installed.

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
Electrical wiring diagram:
AC100~120V
TS
120V 200W
120V 200W
Heater
Heater
Thermostat
Fuse
ON/OFF switch

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
CUSTOMER SERVICE POLICIES
Standard Parts:
Customer Service will strive to ship stock parts within 24 hours of receipt of purchase order.
Most non-stock parts will be available for shipment within 5-10 business days of receipt of purchase
order.
A 30% re-stock fee will apply to all returned parts received in new and operable condition within 30
days of shipment.
Special Parts:
Special non-stock items may have considerable lead times. Customers who use special (non-stock)
items are encouraged to keep these items in stock.
Returns are acceptable at the sole discretion of Glue Machinery Corporation. No equipment or
goods are to be returned without a Glue Machinery return authorization number. If an item is
deemed returnable, a re-stocking fee of up to 50% will apply to special or non-stock items.
Shipments:
Most shipments are routed UPS. Shipments over 150 pounds are forwarded via trucking service.
Same day (24 hour) special handling:
Rush orders are accepted.
NOTE: CUSTOMER SERVICE DIRECT DIAL PARTS - 1-888-202-2468
Prices and Terms subject to change without notice.

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
TECHNICAL SERVICE POLICIES
Repairs (at Glue Machinery Corporation facility):
Items determined repairable are invoiced at cost of materials plus $75.00/hour labor. Estimates will
be made prior to any repair service.
Most guns are repairable and should not be discarded. Please call Glue Machinery personnel to
determine the feasibility of repairing questionable equipment.
Customer is responsible for all freight charges.
Installation Supervision:
Glue Machinery Corporation provides in plant technical supervision at a rate of $850.00 per day,
plus expenses.
Two weeks notice is necessary to schedule Glue Machinery Corporation technical personnel.
Customers are responsible for pre-installation preparation. Information is provided for machine
and head mounting, electrical information, timing information, etc.
Missed appointments, or those cancelled with less than 24 hours notice, will be charged at the full
rate of $850.00, plus expenses.
If Customer is not prepared for a scheduled service visit, the day will be charged at $850.00 plus
expenses.
Technical Service (in-field repair):
Technical service personnel are available to all Glue Machinery Corporation customers. Glue
Machinery Corporation should be contacted at 888-202-2468 if a technician is needed.
Service charges are: $100.00/hour - Monday through Friday, plus expenses; and $150.00/hour on
weekends and holidays, plus expenses. Mileage is charged at $0.52/mile. Minimum service charge is
$425.00 plus expenses. Under certain circumstances, time is charged from the time a Glue
Machinery Corporation technician leaves his location until he returns to that location. The customer
will be notified in advance of this situation and the customer must authorize these charges.

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
TERMS AND CONDITIONS OF SALE
1. ENTIRE AGREEMENT: These Terms and Conditions, together with terms on the face of
Seller’s invoice, shall constitute the entire and exclusive contract (“Agreement”) between
Seller and Buyer. This Agreement is intended to be a final expression of the parties’
understanding and agreement with respect to its terms and shall supersede all prior
negotiations, promises, agreements and representations not set forth herein. Seller’s
acceptance of Buyer’s order is expressly conditioned on Buyer’s assent to these Terms and
Conditions of Sale. Any order, whether quoted, shipped or received by Seller, shall be
construed as a written acceptance by Buyer of Seller’s offer to sell in accordance with this
Agreement, and any such order shall be filled in accordance with the terms as provided in
this Agreement. No other terms and conditions shall apply unless specifically accepted by
Seller in writing. No modifications of this Agreement shall be of any force and effect unless
such modifications are made in writing and signed by the party claimed to be bound thereby.
Additionally, no modification shall be effected by an acknowledgment or acceptance by
Seller of any oral or written purchase order from Buyer containing any different terms and
conditions, and any such inconsistent terms and conditions shall be deemed to be superseded
by this Agreement and the other documents delivered by Seller to Buyer.
If for any reason Buyer fails to accept this Agreement in writing, any conduct that
demonstrates the existence of a contract, including, without limitations, the delivery of items
in accordance with this Agreement prior to written acceptance hereof and acceptance of such
items by Buyer, shall constitute an agreement to all of the terms and conditions stated herein.
The provisions herein set forth, plus all drawings, constitute the entire contract between the
Seller and the Buyer and supersede all prior Proposals, purchase orders, correspondence and
other communications, whether written or oral, between the Seller and the Buyer. No provision
of these conditions of Sale shall be subject to change except by the written authorization of a
properly authorized representative of the Seller.
2. PRICE: The prices set forth on the face of Seller’s quotation or invoice is only for the
quantities of items listed and the specifications indicated. Except as otherwise indicated on
the face of Seller’s invoice, Buyer is responsible for all freight and transportation charges,
and all items will be billed at the prices (including applicable freight and transportation

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
charges) in effect as of the date of shipment. All prices and extras, including all freight and
transportation charges, are subject to change by Seller at any time without prior notice. In
addition, all prices are subject to the addition of an applicable use, sales, excise or other taxes
levied by any federal, state or local authority, and Buyer shall be responsible for any such
taxes. Any excises, levies or taxes which Seller is required to pay or collect, under any
existing or future law or regulation (domestic of foreign), upon or with respect to the sale,
purchase, delivery, storage, processing, use, consumption or transportation of any of the
items covered hereby, shall be for the account of Buyer and Buyer agrees to promptly pay the
amount thereof to Seller upon request.
3. DELIVERY AND RISK OF LOSS: Unless otherwise stated in Seller’s quotation or
invoice, delivery shall occur, and risk of loss shall pass to Buyer upon delivery of the items to
Buyer’s designated shipping carrier. All items shall be delivered and shipped in accordance
with the delivery schedule and instructions indicated on the face of Seller’s invoice;
provided, however, that delivery dates are approximate and are subject to reasonable
variation. The amount of all applicable taxes, federal, state or local, will be charged in
Maryland unless the purchase order clearly states that the equipment of goods are tax exempt
and an exemption certificate is on file at the Seller’s location. Any personal property or other
tax assessable on the equipment or applicable taxes outside of Maryland shall be the sole
responsibility of the buyer.
4. PAYMENT: Unless otherwise specified, the terms of payment for each order under this
Agreement shall be net cash in 30 days from the date of invoice. C.O.D. or prepayment may
apply to new customers. Transactions are FOB Seller's factory exclusive of sales or use taxes.
All payments shall be in the legal currency of the United States. All prices are subject to
exception or change without notice. Pricing errors may be corrected at any time. The Seller
may, at any time and without obligation, suspend performance or require payment in cash,
security, or other adequate assurances satisfactory to the Seller when, in the opinion of the Seller
in its sole discretion, the financial circumstances of Purchaser warrant such action. Seller shall
retain title to all items as security until payment for same has been received. If Buyer at any
time fails to make payment as required under this Agreement, Seller may, in addition to any
other remedies that it may have as provided by law or in equity, suspend its own performance
hereunder and demand collateral sufficient to ensure the payment of all outstanding amounts
that are then due and/or that may become due in the future under this or any other agreement
between the parties.

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
5. FREIGHT: Buyer is responsible for all freight and forwarding charges, import fees, customs
fees, duties, taxes, etc.
6. LIMITED WARRANTY AND DISCLAIMERS: All equipment and goods are warranted
by the Seller to be free from defects in material and workmanship as follows:
All items except electrical components and hot melt hoses for a period of six (6) months from
date of shipment or one thousand (1,000) hours of use, whichever occurs first.
All electrical components for a period of ninety (90) days from the date the equipment or
goods were shipped, and
For hot melt hoses for a period of six (6) months from date of shipment.
This warranty does not apply to equipment or goods which are, by the sole discretion of the
seller, misused, abused, damaged from installation, or not used in accordance with seller’s
instructions. Normal wear of equipment or goods is not included in this warranty.
Equipment or goods not manufactured by the Seller but supplied through the Seller shall
carry the warranty of the original manufacturer.
Seller assumes no responsibility for the quality or performance of coatings, adhesives or
other materials used with Seller’s equipment or goods.
Subject to the limitations set forth in these terms and conditions, Seller warrants that the
item(s) sold to Buyer will, under normal use and service, conform to any specifications that
are listed in this Agreement. Seller reserves the right to change any of its specifications, if
applicable, at any time. The limited warranty set forth in this paragraph expires at the earlier
of (i) six months after date of shipment or (ii) the period or shelf life specified in the
applicable Technical Data Sheet (the “Warranty Period”). This limited warranty is the sole
and exclusive warranty provided under this Agreement and extends only to the original
Buyer from Seller and does not extend to any subsequent purchases or any other uses of any
item sold hereunder. No claim against Seller, including but not limited to personal injury
claims relating to any products, shall be allowed by any party other than the Buyer. NO
OTHER WARRANTY, WHETHER EXPRESS, IMPLIED OR STATUTORY,
INCLUDINGANY WARRANTY OF MERCHANTABILITY, INFRINGEMENT,

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
FITNESS FOR PARTICULAR PURPOSE OR OTHERWISE, SHALL EXIST IN
CONNECTION WITH THE SALE OR USE OF ANY ITEM HEREUNDER.
ADDITIONALLY, NO REPRESENTATION OR WARRANTY MADE BY ANY
SALES REPRESENTATIVE OR SELLER WHICH IS NOT SPECIFICALLY SET
FORTH HEREIN SHALL BE BINDING UPON SELLER. All claims under this
warranty must be made in writing and delivered to Seller at the address listed in Seller’s
invoice prior to the expiration of the Warranty Period or such claims shall be barred.
Glue Machinery Corporation and/or its respective suppliers make no representations about
the suitability of the information contained in the documents and related graphics published
on GlueMachinery.com for any purpose. Corresponding images and/or example photos
depict professionals and should not be relied upon when operating any of the depicted
machinery. Glue Machinery Corporation hereby disclaims all warranties and conditions with
regard to this information, including implied warranties. The documents and related images
published on GlueMachinery.com or other advertising materials could include technical
inaccuracies or typographical errors. Glue Machinery Corporation reserves the right to make
improvements and/or changes to GlueMachinery.com at any time.
The limited warranty provided for herein does not cover, and specifically excludes, material
failure resulting from normal wear and tear, abuse, neglect, improper installation, faulty
maintenance, accidental or intentional damage, damage from fire, floods, earthquakes or
other acts of God, and/or defects resulting from seller’s compliance with Buyer’s
specifications. Additionally, it is solely Buyer’s responsibility to test and determine the
suitability of any item for any intended use, and although Seller may have recommended an
item or developed an item at Buyer’s request, Buyer assumes all risk and liability whatsoever
regarding the item’s suitability for Buyer’s or any other intended use.
7. LIMITATIONS OF LIABILITY. Upon receipt of a timely warranty claim from Buyer in
accordance with these terms and conditions, Seller shall have the option either to inspect the
item while in Buyer’s possession or to request Buyer to deliver the item to Seller at its
factory or other designated site, at Buyer’s expense, for inspection by Seller. Seller shall, at
its option, either (i) replace any item that has been properly selected, stored and used and is
reasonably determined by Seller to be in breach of the warranty set forth in the foregoing
paragraph of these terms and conditions, in which case seller shall then ship the replacement
item to Buyer F.O.B. point of shipment; or (ii) if in Seller’s sole judgment circumstances are

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
such as to preclude the remedying of a breach of any warranty by replacement, Seller shall
refund to Buyer, by issuance of a credit or otherwise, the applicable part of the purchase price
theretofore paid to Seller. IN NO EVENT SHALL SELLER’S LIABILITY FOR ANY
DEFECTIVE ITEMS UNDER THIS AGREEEMENT EXCEED THE PURCHASE
PRICE THEREOF. IT IS EXPRESSLY AGREED THAT REPLACMENT OR
REFUND OF THE PURCHASE PRICE SHALL BE THE SOLE AND EXCLUSIVE
REMEDY FOR ANY BREACH OF WARRANTY OR ANY OTHER CLAIM IN
RESPECT OF SUCH ITEMS, INCLUDING, WITHOUT LITMITATIONS, THOSE
CLAIMS BASED ON CONTRACT, WARRANTY, TORT, OR STRICT LIABILITY.
SELLER SHALL NOT UNDER ANY CIRCUMSTANCES BE LIABLE FOR
REMOVAL OR INSTALLATION COSTS, DISPOSAL COSTS, LABOR COSTS,
DOWNTIME, DAMAGE TO OTHER PROPERTY, LOSS OF BUSINESS OR
PROFITS, OR ANY SIMILAR OR DISSIMILAR INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES. The sole purpose of the stipulated exclusive remedy set
forth in this paragraph shall be to provide Buyer with free replacement or refund for
defective items in the manner provided herein. This exclusive remedy shall not be deemed to
have failed of its essential purpose so long as Seller is willing and able to replace defective
items in the manner prescribed herein or to provide a refund if, in Seller’s judgment,
replacement is not feasible or appropriate under the circumstances.
8. ITEM RETURNS: Seller, in its sole and exclusive discretion, shall have the right to accept
returns of item(s) from Buyer during the applicable Warranty Period. No item shall be
returned, however, unless (i) Seller has issued to Buyer a written return authorization
number, (ii) Buyer has a valid receipt for the item, and (iii) the Warranty Period has not
expired. Buyer shall be responsible for any costs and expenses associated with the return of
any item, including, but not limited to, any applicable shipping costs, restocking fees and any
costs associated with the proper disposal of the returned items.
9. FORCE MAJEURE: Seller shall be excused from, and shall have no liability for, any
prohibitions, failures, interruptions or delays in the manufacture or delivery of any items
which may be occasioned by matters beyond the control of Seller, including, but not limited
to, any act of sabotage, fire, flood, storms, explosion, labor dispute, strike, work stoppage,
riot, insurrection, war, act of, or priorities granted by request of or for the benefit, directly or
indirectly, of any government body, authority or agency, shortage of raw materials or
supplies, act of God, or any other causes beyond Seller’s control. In the event of any such

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
prohibition, failure, interruption or delay in manufacture or delivery, Seller may, at its option,
extend the delivery time or cancel the order in whole or in part. IN NO EVENT SHALL
SELLER BE LIABLE UNDER ANY CIRCUMSTANCES FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES OR CLAIMS OF ANY NATURE RESULTING
FROM FAILURE OR DELAY IN DELIVERY.
10. TERMINATION/CANCELLATION: In addition to any other remedies that Seller may
have as provided by law or in equity, if Buyer (i) fails to make any payment when due
hereunder, or (ii) fails on request to give proper shipping instruction, or (iii) fails to accept
delivery at times stated, or (iv) becomes insolvent or otherwise voluntarily or involuntarily
becomes subject to any bankruptcy or receivership proceedings, or (v) otherwise fails to
comply with any terms and conditions of any contract between Buyer and Seller, Seller shall
have the right at its option to terminate this Agreement, recover damages and deduct any
undelivered quantities of items from the total quantities of items to be furnished to Buyer,
whether under this or any other contract between Buyer and Seller. Additionally, Seller may,
at any time or times, suspend performance of any order or require payment in cash, security
or other adequate assurance satisfactory to Seller when, in Seller’s sole opinion, the financial
condition of Buyer or other grounds for insecurity warrant such action.
Buyer shall not be permitted to modify or cancel orders without the prior written consent of
Seller. In no event shall any order be modified or cancelled for any portion thereof already
manufactured, blended or in the process of manufacture or blending at the time the request
for modification or cancellation is received by Seller. Seller, in its sole and exclusive
discretion, shall have the right to make exceptions to this cancellation/modification
requirement upon such terms as are satisfactory to Seller and that will protect and indemnify
Seller against all loss.
Seller intends to comply with all federal, state and local laws and regulations applicable to
the performance by Seller of each order, but any failure of Seller to so comply shall not be a
defense to, or excuse Buyer from, performance by Buyer of any order.
11. INDEMNIFICATION: Seller shall not be liable for any inaccurate, incomplete, or faulty
specifications supplied by Buyer, nor will seller be liable for any infringement or alleged
infringement of any patent, trademark, design, or other intellectual property rights arising out
of Seller’s compliance with Buyer’s specifications. To the fullest extent permitted by law,
Buyer shall protect, defend, indemnify and hold harmless Seller, its directors, officers,

Champ Stick TM 400 Manual
Part # G25E03-001
Glue Machinery Corporation TM
4234 Boston St, Baltimore, Maryland 21224
Toll Free 1-888-202 2468 | Phone: [phone] | Fax: [phone]
Email: [e-mail] | GlueMachinery.com
shareholders and employees (collectively “Seller”) from and against any and all manner of
actions, claims, demands, damages, losses, liabilities, penalties, judgments, costs and
expenses of any kind whatsoever (including without limitation, attorneys’ and consultants’
fees and expenses), whether in law or in equity or otherwise, arising out of or relating to (i)
any inaccurate or faulty specifications supplied by Buyer, or (ii) any infringement or alleged
infringement of any patent, trademark, design or other intellectual property rights resulting
from Seller’s compliance with Buyer’s specifications, or (iii) any personal injuries or
property damage sustained or allegedly sustained by any person (including, but not limited
to, Seller’s agents and employees) as a result of Buyer’s active or passive negligence or
misconduct; or (iv) Buyer’s or any third party’s failure to test and determine the suitability of
any item for Buyer’s or any other intended user; (v) Buyer’s or any third party’s misuse or
failure to use any item in a manner that does not conform to the applicable item
specifications or to the requirements of any applicable federal, state or local law or
requirement; or (vi) any third party claims asserted against Seller as a result of Buyer’s or
any other third-party’s use of any item purchased hereunder. The provisions of this
paragraph shall survive the delivery of and payment for all items under this Agreement and
shall apply irrespective of whether Seller is also actively or passively negligent or otherwise
at fault. In addition, this indemnity specifically covers any claims that may be asserted by
Buyer’s employees, and Buyer hereby expressly waives, for purposes of this indemnity only,
any immunity it may have under any worker’s compensation or other law from liability for
claims brought by Seller pursuant to this paragraph.
Buyer’s indemnity obligations to Seller hereinabove shall not be limited by any limitation on
the amount or type of damages, benefits or compensation payable by or for Buyer under
worker’s compensation acts, disability benefit acts or other employee benefit acts on account
of claims against Seller by an employee of Buyer or anyone employed directly or indirectly
by Buyer or anyone for whose acts Buyer may be liable. In no event shall Buyer’s liability
hereunder be limited to the extent of any insurance available to or provided by Buyer.
12. GOVERNING LAW: This Agreement shall be governed by, and construed in accordance
with, the laws of the State of Maryland without regard to its conflicts of laws. Any and all
disputes arising under this Agreement shall be resolved in a state or federal court of
competent jurisdiction within the State of Maryland and Buyer hereby irrevocably submits to
the jurisdiction of any such court for the resolution of any and all disputes arising hereunder.