Glynn Johnson PL7 User manual


829696-00
A. Cover with Emergency Release Button
B. Cover Screws
C. PL7/8 Mounting Screws
D. Pull Assembly
E. Latch
F. Latch/Deadbolt/Strike Screws
G. Strike
H. Strike Box
J. Push Assembly
K. PL7/8 Mounting Nuts
L. Cover with Thumbturn
M. Lead Washers (Optional)
N. Lead Latch Cover (Optional)
P. Roller Bracket
Q. Roller Bracket Screws
R. ASA Strike Screws
S. Roller Strike Screws
C
B
A
D
E
F
H
G
J
K
L
GH
R
Optional ASA Strike
Tools for Install
OR
F
N
M
Tools for Preparation
G
PQ
Optional Roller Strike
S
Privacy Latch
PL7/PL8
Installation Instructions

6
Install Push Lever and Pull Lever
4Install Latch
5Position Cams as Shown
7Install Covers
1Use Templates from Back Page to Check Holes
NOTE: If door holes do not match template, see
Door Preparation section on back page.
Template #1
Template #2 or #3
Push
Pull
PL7 has Thumbturn on Push Side
PL8 has Thumbturn on Pull Side
Install Privacy Latch
Push handle Pull handle
Actuator Pin
Cam
Cam
Actuator Pin
Push Pull
Thumbturn
Emergency
Release
Button
For Lead Lined Model ONLY, Install Lead Lining
2
Adapter Plate
3
Lead Washers (2)
For Roller Strike Model ONLY, Install Adapter Plate
Push
Pull
Lead Wrap

8Install Strike
NOTE: If frame not prepared, see Frame
Preparation below.
1Use Strike as a Pattern to Mark Frame
Mortise for Strike
NOTE: Strike should be flush to frame.
Standard
strike
Roller
strike ASA strike
3
OR OR
Frame Preparation
Door
Drill Holes
2
1¹⁄₄"
(32 mm)
1"
(25 mm)
¹⁄₂" Deep
(13 mm)
Latch
Standard Strike Roller Strike
ASA Strike
OR OR
Standard
Wood - #32
Pilot Drill
Metal -
#29 Drill, #8-32 Tap
ASA Strike or Roller Strike
Wood - ¹⁄₈
" (3mm) Pilot Drill
Metal -
#17 Drill, #12-24 Tap

© Allegion 2014
Printed in U.S.A.
829696-00 Rev. 08/14-e
2¹⁄₈" (54 mm)
Hole
1" (25 mm)
Hole
Template #1 C
L
C
L
2
3Drill Holes
Mark Door
4
Door Preparation
₈
⁄
⁵1 "m
m
1
4
()
Mortise to ⁵⁄₃₂"
(4 mm) depth
Door Edge
¹⁄₈"
(3 mm)
C
L
C
L
Latch
1¹⁄₈"
(29 mm)
1"(25mm)
Hole
2¹⁄₈"
(54 mm)
Hole
1" (25 mm)
Hole
Temp late #1
Push/Pull
Latch
3³⁄₈"(86mm)
C
L
C
L
1Mark Center Lines ( )
C
L
Backset
2³⁄₄ ", 3 ³⁄₄", 5", or 7"
(70, 95, 127, or 178 mm)
C
L
C
L
C
L
Mortise for Latch
₈
⁄
⁵1 "m
m
1
4( )
Mortise to ⁵⁄₃₂"
(4 mm)depth
Door Edge
¹⁄₈"
(3mm)
C
L
C
L
Latch
1¹⁄₈"
(29 mm)
1"(25mm)
Hole
2₈
⁄
¹"
5( 4m
m)
Hoe
l
1" (25mm)
Hoe
l
Template #1
Push/Pull
Lact h
3³⁄₈"(86m
m)
C
L
C
L
Vertical Horizontal
Minimum
Backset
7” (178 mm)
OR
1³⁄₄" (44 mm)
3³⁄₈" (86 mm)
⁵⁄₁₆" (8 mm)
4 places
₈⁄
⁵
1)
m
m
14("
Mortise to ⁵⁄₃₂"
(4 mm) depth
Door Edge
2¹⁄₄" (57 mm)
C
L
C
L
Latch
1¹⁄₈"
(29 mm)
mm
5
2("
1)
e
lo
H
₈⁄⁷2 )mm37(
"
Mortise to ¹⁄₄"
(6 mm) depth
Door Edge C
L
C
L
Latch
1¹⁄₈"
(29 mm)
"
1)m
m52(
eloH
Template #2
(standard latch)
Template #3
(latch with roller adapter)
Wood - #32 Pilot Drill
Metal -
#29 Drill, #8-32 Tap
3³⁄₈" (96 mm)
Wood -
#32
Pilot Drill
Metal -
#29
Drill, #8-32 Tap
45" (114.3 cm)
From Finished Floor
Recommended
1¹¹⁄₁₆" (43 mm)
1³⁄₈"(35 mm)
Customer Service
1-877-671-7011 www.allegion.com/us