Go Power GP-ISW-700 User manual

GP-ISW Series
Pure Sine Wave Inverter
Quick Start Guide
Find tech tips, manuals and support at gpelectric.com
Specications
Do not open or disassemble the Inverter. Attempting to do so may cause risk of electrical shock or fire.
We guarantee this product against defects in materials and workmanship for a period of 24 months
from the date of purchase. In case you need to repair or replace any defective power inverters, please
contact your local Go Power! distributor.
This warranty will be considered void if the unit has been misused, altered, or accidentally damaged.
Go Power! is not liable for anything that occurs as a result of the user’s fault.
Please read the Owner’s Manual BEFORE connecting to the supply.
You can view and download the manual at
https://gpelectric.info/ISWManual
Note: Both 12V and 24V inverter specifications are listed below.
Remote port (RJ-11)
Remote control green terminal
Chassis ground
DC input connector
Saving power adjustment
Function switch
Function LED
TRC port (RJ-45)
AC output socket
Main switch
ISW 700, 1000, 1500, 2000, 3000
UL 458
Part 15,
Class B
GP-ISW700 GP-ISW1000 GP-ISW1500
Continuous Output Power 700 W (VA) 1000 W (VA) 1500 W (VA) Maximum Surge Rating 1230 W (VA) 1750 W (VA) 2650 W (VA)
12 V: 91% 24 V: 93%
12 V: 92% 24 V: 93%
12 V: 91% 24 V: 92%
No Load Current Draw / Powersave 12 V: ≤ 1.5 A / < 0.1 A
24 V: ≤ 0.8 A / < 0.06 A
AC Output Connections Dual GFCI Outlet Remote Power Option Dimensions (L x W x H) 13.00 x 7.87 x 3.27”
(330 x 200 x 83 mm
14.65 x 7.87 x 3.27”
(372 x 200 x 83 mm)
16.59 x 9.76 x 3.27”
(421 x 248 x 83 mm)
Weight 5.73 lbs (2.6 kg) 7.19 lbs (3.26 kg) 9.13 lbs (4.14 kg)
Warranty Inverter Install Kits GP-DC-KIT2 12 V: GP-DC-KIT3
24 V: GP-DC-KIT2
Remotes (Optional) Regulations and Safety UL 458, FCC Part 15 Class B
GP-ISW2000 GP-ISW3000
2000 W (VA) 3000 W (VA) 3500 W (VA) 6000 W (VA)
12 V: 92% 24 V: 93%
12 V: 90% 24 V: 91%
12 V: ≤ 3.8 A / < 0.4 A 24 V: ≤ 2.0 A / < 0.2 A
Hardwire
17.45 x 9.76 x 3.27”
(443 x 248 x 83mm)
17.40 x 10.04 x 6.22”
(442 x 255 x 158mm)
11.55 lbs (5.24 kg) 18.08 lbs (8.2 kg)
12 V: GP-DC-KIT4 24 V: GP-DC-KIT3
12 V: GP-DC-KIT5 24 V: GP-DC-KIT3
UL 458, FCC Part 15 Class A
Output Waveform Output Voltage Range ± 3% Input Voltage
Pure Sine Wave
100 - 120 VAC (Dip Switch Selectable)
12 V: 10.5 - 16.5 VDC
24 V: 21 - 33 VDC
12 V: ≤ 1.8 A / < 0.1 A
24 V: ≤ 1.0 A / < 0.05 A
Over/Under Voltage, Reverse Polarity (Fused)
Short Circuit, Overload, Over/Under Temperature
Input Protection Output Protection Low Battery Alarm ± 0.3 V (± 0.5 V for 24 V inverters) Low Battery Shutdown ± 0.3 V (± 0.5 V for 24 V inverters)
12 V: 10.5 V
24 V: 21 V
12 V: 10.5 V
24 V: 21 V
-4˚ F - 104˚ F (-20˚ C - 40˚ C)
-22˚ F - 158˚ F (-30˚ C - 70˚ C)
Temperature and Load Controller Cooling Fan
Operating Temperature Range Storage Temperature Range Cooling
Yes
2 Years
GP-ISW-R / GP-SWR-A
1
1
2
3
4
5
6
2
4 5 63
7
8
9
10
7
810 109

Installation and Wiring - Overview
The GP-ISW should be located as close to the batteries as possible but
not within the same compartment. The length and size of the DC Cables
will affect performance. Long DC wires tend to lose efficiency and reduce
the overall performance of the Inverter/Charger.
For optimum Inverter performance the GP-ISW must be installed so the
front and rear air vents are not blocked or obstructed in any way. Do not
install the GP-ISW in an area with limited air flow. Allow as much space
around the Inverter as possible, leaving at least 4 inches of airspace
clearance around all ventilation areas.
• Flathead Screwdriver (for wire terminals)
• Philips Screwdriver (for mounting screws)
Tools and Materials Needed
Mounting Orientations
See user manual for complete instructions at gpelectric.com
LED Indicators
LED Status DC 12V DC 24V
Red
Orange
< 11.0V
11.0 ~ 11.5V 22.0 ~ 23.0V
Green 11.5 ~ 15.0V 23.0 ~ 30.0V
< 22.0V
Orange 15.0 ~ 15.5V 30.0 ~ 31.0V
Red < 15.5V > 31.0V
Input Voltage Level
LED Status Status Recovery Point
Green
Red
Normal
Over Current Protection/
Over Load Protection (AC
output short-circuit and over
load)
Under Temperature Protection/
(Heat sink temp. under -20°C)
Under Voltage Protection/
(Input DC voltage under
spec)
Over Temperature Protection
(Heat sink temp. over 80°C)
Red Blink 12.5V @ DC12V System
25V @ DC24V System
14.5V @ DC12V System
> 0°C
(Heat sink temperature)
< 60°C
(Heat sink temperature)
29V @ DC24V System
Red Fast Blink Over Voltage Protection
(Input DC voltage over spec)
Orange
Orange Fast Blink
Orange Slow Blink
Device startup process
abnormal -
Input Voltage Level
HORIZONTAL WALL MOUNT, BASE DOWN
HORIZONTAL MOUNT,
BASE DOWN
HORIZONTAL MOUNT,
BASE UP
VERTICAL MOUNT, DO NOT MOUNT
THE GP-ISW IN THIS CONFIGURATION
GP-ISW-R-12
Remote Control
Battery
GP-TS-30
Transfer Switch
LOAD