GOEBEL GO - LB1 User manual

User Manual
User Manual
innovative fastener solutions
GO - LB1
Cordless Lockbolt Battery Tool

2| Deutsch1| English
Instruction manual: GO-LB1
Table of contents
www.goebel-group.com
Page
Safety measures 2 - 4
Daily maintenance & Environmental protection 4
1. Tool overview
1.1 Capacity
1.1 Technical parameters
1.2 Conguration/ Accessories (see g. A)
1.3 Parts list (see Fig. B)
1.4 Tool parts list of the GO-LB1
4
5
5
5 - 6
7
8
2. Preparing the tool
2.1 Checking the battery
2.2 Checking the tool
9
10
10
3. Tool operation
(important tips before starting work)
3.1 Preparation and review of the specication
3.2 Instructions for the setting process
11
11
11 - 12
4. Charger & Batteries
4.1 Technical parameters
4.2 Using the charger
4.3 Using the battery
13
13
13
13
5. FAQ (Questions / Answers) 14
6. Troubleshooting
6.1 Malfunctions
6.2 Possible causes
6.3 Corrective measures
14
14
14
14
7. Protection conditions & CE certication 15

Deutsch | 2English | 2
To reduce the risk of electric shock, personal injury, re and property damage, be sure
to follow the safety precautions below.
Description of the symbols:
www.goebel-group.com
Safety precautions
Danger
Indicates potential danger of serious injury or death
Warning
Indicates potential danger of serious injury or death
Caution
Indicates the risk of a minor injury
The following signs are used to classify and describe the types of information to be
followed.
This sign is used to alert the user to the prohibited action steps.
This sign is used to draw users' attention to the operating steps that must be
carried out to use the tool.
• This tool is restricted to setting lockbolts and must not be used for impact or other
purposes, such as a hammer.
• Do not overload the lockbolt tool. Please use it only within the range specied in the
function settings.
• Do not block the ventilation openings of the motor. Do not insert any objects into the
ventilation openings.
• It is recommended to wear safety glasses and personal protective equipment such as
gloves, hard hat, safety shoes, noise-insulating earplugs, fall protection devices and
other necessary protective measures when using this tool.
• Please keep the packaging boxes and accessories in a safe place and handle them
with care.
• The tool and accessories should be placed in the plastic case, stored in a dry place
and out of the reach of children.
Please keep the packaging box and accessories and handle them with care.
• The tool and accessories should be placed in the plastic case, stored in a dry place
and out of the reach of children.

2| Deutsch3| English
Safety precautions
www.goebel-group.com
Use of the battery
• Do not charge damaged, dirty or wet batteries.
• Batteries must not be thrown into water or re at any time, used batteries must not be
disposed of as you please
• Do not charge when the ambient temperature is below 0°C or above 45°C.
Use of the charger
• The original battery and the manufacturer's charger must be used for charging.
• Do not charge the battery with a damaged, dirty or damp charger.
• Do not place metal objects in the charging area as a short circuit may occur.
• This charger must not be used by persons with disabilities, mental disabilities or
persons without training or knowledge unless a safety ofcer is on site to supervise
or instruct them in its use.
Danger
• The lockbolt setting tool must not be used in a damp environment or in the vicinity of
ammable liquids and gases. Danger of explosion!
• Do not point the lockbolt setting tool at yourself, others or animals.
• Do not load in a damp environment, near an open re or in an environment with am-
mable, highly combustible gases that can easily be detonated.
Warning
• Tools should be placed so that they do not fall down to avoid unnecessary damage
and safety accidents.
• When installing the battery, be sure to x its position. After you hear a "click" sound the
battery is properly placed.
• When servicing this lockbolt settersetting tool, make sure that the charger and its
power supply equipment are in good condition.
• Use a power supply unit that matches the charger.
• Plugs, power cords and chargers should be checked regularly. If a problem is found, it
should be repaired by the maintenance personnel.
• Maintenance personnel must have professional skills; only qualied professionals
can carry out repairs. If in doubt, please return the tool to the authorised dealer or
manufacturer for repair.
• Original spare parts must be used during maintenance.

Deutsch | 2English | 4
www.goebel-group.com
Maintenance
• Regular maintenance prolongs the life of tools with a lithium battery and should
be carried out by an authorised dealer or manufacturer. For more frequent use, it is
recommended that maintenance be carried out in advance.
• Maintenance of the lockbolt tool is limited to replacement of worn parts and quick
wear parts, clamping jaws, clamping jaw sliders, etc. only, if necessary (see page 8
for replacement accessories).
• To keep the tool in good working condition, please check the tool's wearing parts fre-
quently. In case of wear or damage, please contact your dealer or the manufacturer.
Repair
• The warranty period is 1 year from the date of sale. Excluded from this are quick wear
parts e.g. clamping jaws, jaw sliders etc.
• Failure to comply with the relevant installation and commissioning instructions or fai-
lure to follow the operating procedures may result in the warranty being invalidated.
Environmental protection and resource recycling
• When replacing lithium batteries used in this product, the following points must be
observed:
• If your country or region has regulations, please be sure to take the old battery to a
professional company for disposal.
• Do not throw old batteries into the rubbish, re or water!
1. Tool overview
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
9
10
Name of the component
Screw Cap
Mouthpiece
LED Light
Trigger
Collector
Tool Housing
Battery
Charger

2| Deutsch5| English
www.goebel-group.com
1.1 Capacity / Technical parameters
245
260
92
64
Model GO-LB1
Motor 18V Brushless motor
Noise level < 78dB
Setting Mode Conventional setting mode
Traction Power 23000N
Stroke 16 mm
Net weight (incl. battery) 1,5Kg
Capacity ø 4,8 to 6,4 mm
Material specication All materials and specications of extensive grip range lockbolts and the
6-groove lockbolts
1.2 Conguration / Accessories
(Fig. A)
55
52
37
20
45
GO-LB1
68

Deutsch | 2English | 6
www.goebel-group.com
1.2 Conguration* / Accessories GO-LB1 (see g. A)
NO Parts description Code Spec Qty.
1 Screw cap 2277010210 1
2Mouthpiece 2277040210 Ø 6,4 1
3 Clamping Sleeve 2277040310 Ø 6,4 1
43-jaw set 2277040410 Ø 6,4 1
10 Mandrel collector 2277011610 1
15 Mouthpiece 2277041810 Ø 4,8 1
16 Clamping Sleeve 2277041910 Ø 4,8 1
17 3-jaw set 2277042010 Ø 4,8 1
18 Wrench 2277012310 1
27 Plastic case 2277013310 1
19 Battery Li-Ion 18V 2.0 Ah 2277012410 2
20 Battery Charger 2277012510 1
* General conguration
Very important note! This product is supplied with the factory default
conguration. If users have other special requirements or wish to
customise the conguration, please contact the dealer or
manufacturer in advance.

2| Deutsch7| English
www.goebel-group.com
Abb. B
1.3 Parts list (Fig. B)

Deutsch | 2English | 8
www.goebel-group.com
1.4 Tool Parts list of the GO-LB1 (see Fig. B)
NO Standard Code Teilbezeichnung Anzahl NO Standard Code Teilbezeichnung Anzahl
1
2277010210 Screw cap
1 14
2277062010 Plastic Cover
1
2
2277040210 Mouthpiece Ø 6,4 mm C6L
1 15
2277041810 Mouthpiece Ø 4,8 mm C6L
1
3
2277040310
Clamping Sleeve Ø 6,4 mm C6L 916
2277041910
Clamping Sleeve Ø 4,8 mm C6L 1
4
2277040410 3-Jaw Set Ø 6,4 mm C6L
1 17
2277042010 3-Jaw Set Ø 4,8 mm C6L
5
2277040510 Gear Box Set
1 18
2277012310 Wrench
6
2277050610 Brushless Motor
1 19
2277012410 Battery Li-Ion 18V 2.0 Ah
2
7
2277011310 Tool body screw
920
2277012510 Battery Charger
1
8
2277011410 Tool Body GO-LB1
1 21
2277049911 Mouthpiece Ø 4,8 mm Magna
1
9
2277011510 Mandrel Release Component
122
2277049811
Clamping Sleeve Ø 4,8 mm Magna 1
10
2277011610 Mandrel Collector
1 23
2277049711 3-Jaw Set Ø 4,8 mm Magna
1
11
2277041210 PCB-Set
124
2277049611 Mouthpiece Ø 6,4 mm Magna
1
12
2277061810 Trigger Spring
125
2277049511
Clamping Sleeve Ø 6,4 mm Magna 1
13
2277011810 Trigger
126
2277049411 3-Jaw Set Ø 6,4 mm Magna
1
*Please note that the shaded parts in the list are wear parts. The serial numbers 5, 6, 11 are structural parts.
* Important note: Serial numbers 2-4, 15-17, 21-26 (shaded part with *) are optional accessories!

2| Deutsch9| English
www.goebel-group.com
2. Preparation of the tool
Make sure that you remove the battery from the lockbolt setter before replacing the
wearing parts (mouthpiece, clamping jaw sleeves and the three clamping jaws),
otherwise there is a risk of injury! Choose a mouthpiece that corresponds to the
specication of the lockbolt. The procedure for replacing the components is shown in
the following illustration:
Before putting the lockbolt setting tool into operation, please read the following important instructions carefully.
Make sure that the battery has been removed from the tool as shown in gure ① In
the order shown above: ② loosen the screw cap with the wrench in the direction of
the arrow. Now you can replace the screw cap, the mouthpiece, the jaw sleeve and the
3-jaws according to ③ Once the process is complete, screw the screw cap back on
according to ④ using the wrench. Now you can reinsert the battery.
① ②
③④

Deutsch | 2English | 10
www.goebel-group.com
 
➁Operation indicator light ➀Button
Press button ➀ once to check the battery.
The power indicator lamp ➁ is always lit:
• Full indicator, 100% energy (green).
• Three lights, 75% energy (green)
• Two lights, 50% energy (yellow)
• One light, 25% energy. (red) Please charge!
2.1 Checking the battery
1
2
3
➀LED Light
➁ Trigger
➂Battery
Install the battery ➂ in the direction of the arrow. Press the trigger ➁, the white LED
light comes on ➀and is always on, indicating that the power is working normally.
Important note:
You save energy with the automatic sleep mode, no operation within one minute and
the white illumination light LED goes out automatically. Thus, the tool goes into auto-
matic sleep mode. When you pull the trigger again, the power supply is restored.
2.3 Checking the tool

2| Deutsch11 | English
www.goebel-group.com
3. Tool Operation (Important tips before starting work)
Please charge the battery to 100% (according to relevant government regulations)
before rst use. Please make sure not to stop charging below 50% of the battery power.
3.1 Preparation and review of specications
In advance, the specications of the lockbolt, the borehole and the thickness of the
workpiece should be considered. Due to different types and specications of lock-
bolts that can be provided by different suppliers, the installation performance will vary
greatly. Therefore, a pre-installation (trial setting) is required, before the ofcial setting
process. We recommend that you use GOEBEL lockbolts for optimum processing.
3.2 Instructions for the setting process
Dept. Technical reference Created by Approved by
Document type Document status
Title DWG No.
Rev.
01.10.21
GO-LB1_Bedieungsanleitung
Elias Goebel
Dept. Technical reference
12345678
1 2 345678
D
E
F
A
B
C
D
E
F
Dept. Technical reference Created by Approved by
Document type Document status
Title DWG No.
Rev. Date of issue Sheet
01.10.21
1/1
GO-LB1_Bedieungsanleitung
Elias Goebel
The lockbolt and the lockring are inserted into the intended drill hole of the component
in the direction of the arrow ①. Note that this is done vertically!
➁ Now that the lockbolt and the lockring are inserted into the workpiece, the setting
tool can be guided to the component (in the direction of the arrow).
➂ The mouthpiece of the GO-LB1 now receives the thread of the lockbolt.
①➁
➂

Deutsch | 2
3. Tool Operation (Important tips before starting work)
English | 12
www.goebel-group.com
12345678
1 2 345678
D
E
F
A
B
C
D
E
F
Dept. Technical reference Created by Approved by
Document type Document status
Title DWG No.
Rev. Date of issue Sheet
01.10.21
1/1
GO-LB1_Bedieungsanleitung
Elias Goebel
12345678
1 2 345678
C
D
E
F
A
B
C
D
E
F
Dept. Technical reference Created by Approved by
Document type Document status
Title DWG No.
Rev. Date of issue Sheet
01.10.21
1/1
GO-LB1_Bedieungsanleitung
Elias Goebel
④ Press the trigger to set the lockbolt. Now the collar is deformed and
locks with the bolt thread.
⑤ The lockbolt breaks off at at the head of the collar and now moves
back into the machine, where it lands in the collection container. The setting
process is completely nished.
⑥ An installation of GOEBEL lockbolts can cover different clamping ranges
with one dimension - preferably the G-GRIP® lockbolt made of stainless
steel is suitable here.
④
⑤
⑥

2| Deutsch
www.goebel-group.com
13 | English
4. Charger & Battery
4.1 Technical parameters
Charger
Output: 18V - 2.0Ah
Input: 100 - 240V /50 - 60HZ/ 1 A
Net weight: 0,27Kg
4.2 Charger usage
At rst, the indicator light ➀ of the charger lights up green. As soon as the battery has
been inserted in the direction of the arrow, the colour of the indicator light changes to red.
Operation Charge control
light (1)
Symbols (2)
Explanation
Measures
Battery charged
in charger
▶Red ligth on ▶The battery is in in good
condition. The charging
time is about one hour.
▶In good condition.
▶Green light on ▶Malfunction of the
battery. Cannot be be
charged.
▶Immediately disconnect the
power supply, remove the battery
and replace it with a new battery.
The battery is
charged
▶Green light on ▶The battery is full. Please
remove the battery.
▶In good condition.
▶Red ligth on ▶When the internal
temperature rises, the
charger stops working.
▶Immediately disconnect the
power supply, remove the battery
and replace it with a new battery.
Battery
Output: 18V - 2.0Ah - 36Wh
Net weight: 0,37Kg
12
4.3 Battery usage
• During use, please check (see page 10 - Battery check) the battery power.
• The battery has deep discharge protection (ECP) and can be recharged about 1000
times.
• Do not use the charger until the battery has cooled down sufciently.
• If the battery's operating time is signicantly reduced during normal use, this
indicates that the battery should be replaced.
➀Charge indicator light
➁ Charging symbols

5. FAQ English | 14
Questions Answers
Battery
▶
Is it okay not to use them for a long time?
▶
Charge the battery at least every 6 months, otherwise it may deteriorate in performance after
6 months.
▶
Does charging after each use affect battery
life?
▶
Suggestion: When the remaining battery time is only 25% (a light on the display) or when the
battery is exhausted, it should be recharged to increase the battery life.
Usage
▶
If the tool housing is used continuously in
conventional setting mode for a period of
time, will the heating in the tool housing
affect normal use?
▶
As the high-speed motor causes the gear to rotate, the heat generated during the setting
process is transferred to the outside, which does not affect the normal use of the tool. The
user is advised to wear suitable protective gloves.
6. Troubleshooting
Malfunction Probable cause Correction of defects
During
Charging
▶
The battery is plugged into the charger and
the green light is on
▶
Battery malfunction or damage, error,
charging not possible.
▶
Stop charging immediately, remove the
battery and replace it with a new battery.
Abnormal charging temperature (battery over-
heating) outside normal range (0°C~45°C)
▶
Red light is on while the battery is charging
▶
Immediately switch off the power,
remove the battery and check the
charger
U
S
A
G
E
▶
All displays on the function panel ash
▶
Low power alarm
▶
Remove the battery
▶
The indicator light ashes once within a
certain period of time and switches off
after 15 seconds.
▶
Motor short-circuit alarm Please send the battery to qualied,
professional maintenance personnel for
inspection and repair. If in doubt, please
contact the authorised dealer in good
time for advice and repair.
▶
The indicator light ashes within a certain
period of time and switches off after 15
seconds.
▶
Overheating alarm of the control unit
▶
Die Anzeigeleuchte blinkt 4 Mal innerhalb
einer bestimmten Zeitspanne und schaltet
sich nach 15 Sekunden ab.
▶
Engine blockage alarm
▶
▶
The indicator light ashes 5 times within
a certain period of time and switches off
after 15 seconds.
▶
Switch-on error or abnormally high current
ow
▶
The lockbolt was not not set correctly
▶
Battery damaged
▶
▶
Use a new battery for the machine
Loose mouthpiece Tighten the mouthpiece
▶
Battery power exhausted, check power
indicator
▶
Charge the battery or replace it with a
new one if necessary.
▶
Discharge the battery. Check the power
indicator panel.
▶
Charging (see page 10: Battery testing, for
use with page 13 -Batteries and chargers).
▶
The lockbolt is not pulled out or torn from
the connection
▶
The 3-piece jaws are worn, the mouthpiece
is dirty, the jaw sleeve or the mouthpiece is
deformed
▶
Replace the jaws, tighten the mouthpiece,
remove impurities and replace the jaw
sleeve or the mouthpiece
▶
▶ ▶
The broken-off lockbolt is stuck in the
clamping jaws / the lockbolt is stuck in the
clamping jaw sleeve
▶
Unscrew the mouthpiece and remove
the broken lockbolt. Also remove the
clamping jaw sleeve and clamping jaws.
▶
The collection container is full and the
torn-off lockbolt returns backwards
▶
Remove the torn-off lockingbolt pins in
the collection container
▶
▶
The wrong choice of mouthpiece or the
mouthpiece is worn out
▶
Take the correct mouthpiece or replace
it with a new one
▶
Loose lockbolt after setting process
▶
Lockbolt selection does not correspond to
the drill hole
▶
Checking and correct selection of the
right lockbolt
If the above methods do not remedy the situation, the setting tool must be repaired by professional personnel or the tool must be returned to the seller or
manufacturer for repair!

15 | English
7. Protection conditions & CE certication
Warranty period & maintenance protection
Our products have a lifetime after-sales service. If a quality problem is found in use,
we will provide warranty.
The warranty period for this tool is 1 year and the start date is based on the sales
invoice.
Damage caused by normal wear and tear, overloading, improper use or by human hand
is not covered by the warranty.
For the quality problem of the tool itself, the manufacturer offers a free repair or re-
placement within the warranty period.
For a free repair or replacement under warranty, only complete tools that have not
been opened or modied independently will be accepted. Wear parts are not covered
by the warranty.
In the event of abnormal use, the manufacturers are not responsible for quality claims.
This includes improper storage, accident, abuse, loss and failure due to equipment
non-conformity. The highest liability for damages is limited to the value of the product
itself and does not apply to the fasteners and application.
If you have any questions, please contact your dealer or the manufacturer directly for
assistance.
We hereby declare that this battery tool complies with the following standards and the
standard documentation when used in accordance with the operating instructions.
CE Certication
EC Compliance Statement
EN 62841-1:2015/AC:2015,
EN 60335-1:2012/A11:2014,
EN 55014-1:2006+A1:2009+A2:2011,
EN 55014-2:2015, EN 61000-3-2:2014,
EN 61000-3-3:2013
related to CE Directive(s):
2006/42/EC (Machinery)
2014/35/EU (Low Voltage)
2014/30/EU (Electromagnetic Compatibility)