Goldair GCPF110 User manual

For model: GCPF110
40CM PEDESTAL FAN
OPERATING INSTRUCTIONS

WARNINGS AND SAFEGUARDS
To obtain maximum benefit from your Goldair appliance please read the instruction manual carefully and
ensure this is understood before using the product.
1. Use only the voltage specified on the rating plate of the appliance.
2. Keep all objects at least 1 metre from the front, sides and rear of the appliance.
3. Do not place appliance close to radiant heat source.
4. Do not operate in areas where petrol, paint or other flammable liquids are used or stored.
5. Do not use the appliance to dry clothes.
6. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may
cause an electric shock, fire or damage to the appliance.
7. Do not operate this appliance with a damaged cord, plug or after the appliance malfunctions
or has been dropped or damaged in any manner. Return to a qualified electrical person for
examination, electrical service or repair.
8. This appliance is intended for household use only and not for commercial or industrial use.
9. Use this appliance only as described in this manual. Any other use is not recommended by the
manufacturer and may cause fire, electric shock or injury.
10. The common cause of overheating is deposits of dust or fluff in the appliance. Ensure these
deposits are removed regularly by unplugging the appliance and vacuum cleaning the air vents
and grills.
11. Do not use abrasive cleaning products on this appliance. Clean with a damp cloth (not wet)
rinsed in hot soapy water only. Always remove plug from the mains supply before cleaning.
12. Do not connect the appliance to mains voltage until completely assembled and adjusted.
13. Switch off and use handles provided when moving.
14. Do not operate with cord set coiled up as a heat build up is likely, which could be sufficient to
become a hazard.
15. The use of an extension cord with this appliance is not recommended.
16. Do not remove plug from power socket until the appliance has been switched off.
17. Do not remove plug from power socket by pulling cord –always grip plug.
18. Always unplug appliance when not in use.
19. Do not twist, kink or wrap the cord around the appliance, as this may cause the insulation to
weaken and split. Always ensure that all cord has been removed from any cord storage area
and is unrolled before use.
20. This appliance is not intended for use by young children or infirm persons unless they have
been adequately supervised by a responsible person to ensure that they can use the appliance
safely.
21. Do not use this appliance in the immediate surrounds of a bath, a shower, or a swimming pool
or other liquids. The appliance must not be immersed in any liquids.
22. When the appliance has been unpacked, check if for transport damage and ensure all parts
have been delivered. If parts are missing of the appliance has been damaged, contact the
Goldair Customer Services Team. (refer to details on back page)
23. If your appliance does not work, or is not working properly, contact the place of purchase of
the Goldair Customer Services Team. (refer to details on back page). Repair work on the
appliance by unqualified persons can cause serious risk to the user.

OVERVIEW OF GOLDAIR COOLING FAN
Your Goldair Cooling Fan is designed to provide direct personal cooling. The fan is equipped with three
speed settings to ensure your precise cooling needs are met.
OPERATING YOUR COOLING FAN
Always choose a safe location for the fan, keeping in mind the safety precautions outlined. Ensure all
packaging has been removed from the unit before use. This appliance requires some assembly it should be
used solely as a portable appliance.
ASSEMBLING YOUR COOLING FAN
ASSEMBLY OF BASE
Firstly, loosen and remove the four screws from the bars. Then cross bar A and bar B so that they interlock.
Be sure to align the four holes in the bars with those on the flange of the Outer Tube. Secure the flange to
the bars with the four screws.
Loosen and remove the Height Adjustment Collar from the top of the Inner Tube. Slide the Base Decorative
Cap down over the assembly. Replace the Height Adjustment Collar on top of the Inner Tube. Pull the
Inner Tube out from the Outer Tube to adjust the tube to the desired height and tighten the collar.
If necessary, slightly loosen the Set Screw by turning it anticlockwise. Slide the Switch Box down over the
Inner Tube and tighten the Set Screw. Make sure the Set Screw is tightly secured.
ASSEMBLY OF BLADE AND GRILL
Unscrew the plastic mounting nut from the front of the motor housing by rotating it anticlockwise.
Position the rear grille against the front of the motor housing with the handle uppermost, ensuing that the
locating pegs on the motor housing are engaged correctly in the holes of the rear grill.
Tighten the Rear Grill Mounting Nut clockwise. DO NOT OVERTIGHTEN IT.
Push the fan blade onto the motor shaft, locating the slot at the back of the blade on the drive pin that
passes through the motor shaft. Tighten the blade cap by turning it anticlockwise.
Position the front grill against the rear grill so that the holes in the rims that accept the small nut and bolt
are in line. Insert the bolt through the holes and screw on the nut. Do not fully tighten at the stage.
Push the grill retaining clips into position ensuring that they engage correctly on the rim of the grill.
Fully tighten the small nut and bolt that passes through the rim of the grill.
POWER CONTROL SWITCH
The control switch positions are:
•0 = OFF
•1 = Low Speed
•2 = Medium Speed
•3 = High Speed
Check that the control switch is set to off position before plugging the fan into the mains supply.
To activate the oscillation function, push down the oscillation pin (7) on the top of the motor. The fan will
then oscillate until the pin is pulled back up.

GOLDAIR COOLING FAN SPECIFICATION
Model No: GCPF110
Power Supply: 230-240V, 50Hz AC only
Power: 50W
PROOF OF PURCHASE
To receive warranty retain receipt as proof of purchase.
PARTS OF YOUR GOLDAIR COOLING FAN
CLEANING
Be sure your fan is in the OFF position.
Unplug the fan before cleaning.
Use only a soft, damp cloth to gently wipe the fan.
DO NOT immerse the fan in water and never allow water to enter the motor housing.
DO NOT use gasoline, paint thinner or other chemicals to dean the fan.
Removal of the Front Grill for Cleaning
To access the fan blade, remove the front guard and securing screw.
Clean the fan blade, front and rear guards with a soft, moist cloth.
Replace blade, tighten securing screw and securely fasten the front guard.

Your Goldair product has been inspected and tested and is guaranteed subject to the
following for a period of 1 year from the date of purchase against defects in workmanship
and materials. During this period, such defects will be rectified by repair or replacement of
the product purchased. Your product contains no user serviceable components and this
warranty becomes invalid if in our opinion the product has been misused, abused,
incorrectly installed, tampered with, connected to an electrical supply not corresponding
with the name plate specification, or subjected to power surges. The warranty does not
include any labour or other associated expense that may be involved in removal or
installation of the product. Normal wear and tear is expressly excluded.
If your Goldair product fails to operate satisfactorily, please return it to the retailer from
whom it was purchased. To obtain a repair or replacement product under this warranty, you
will need to produce satisfactory evidence of date of purchase. The completed warranty and
purchase receipt must be presented with the product. The warranty should be filled out at
the time of purchase. It is in your interest to make sure this is done.
If the product is to be replaced (cannot be repaired) then that replacement will be of the
faulty product or accessory excluding packaging, instruction card etc. Where a replacement
product is supplied, this shall be guaranteed for the balance of the original warranty period.
Any model that is no longer available will be replaced by a model of a value and with such
features as we consider appropriate in the circumstances. Goldair is not responsible for
freight forwarding charges, losses or damage in transit.
If service is required after the warranty period has expired, the product should be returned
to a qualified electrical technician. Service outside of the warranty period will be at your
cost.
Consumers Guarantee Act (1993).
In accordance with the above act consumers are advised that: The manufacturer does not
undertake that repair facilities and parts are necessarily available for this product.
If any of the provisions of the foregoing are contrary to any relevant legislation, then that
provision shall be deemed to be excluded from the warranty and the rest of the provisions
will continue to apply.
1 YEAR WARRANTY
IMPORTANT: PLEASE RETAIN THIS WARRANTY CARD
NAME: .
ADDRESS: .
PURCHASED FROM: .
SUBURB: .
DATE OF PURCHASE: .
NAME OF PRODUCT: .
MODEL No: .

SUPPORT AND TECHNICAL ADVICE
North Shore City, Auckland, New Zealand
Phone: [phone]
Website: www.goldair.co.nz