Goldair GGPH205 User manual

Thank you for choosing a Goldair Panel Heater. This Goldair appliance has been designed
and manufactured to high standards of engineering and with proper use and care, as
described in this booklet, will give you years of useful service. Please read these instructions
carefully and keep for future reference.
YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE
INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL.
1. WARNING you must not cover this appliance. Covering this appliance presents fire risk and will activate the safety fuse;
permanently disabling the unit.
2. Use only the voltage specified on the rating label of the appliance.
3. Keep all objects at least 1 metre from the front, sides and rear of the appliance.
4. This appliance is intended for household use only and not for commercial or industrial use.
5. Indoor use only.
6. Do not use abrasive cleaning products on this appliance. Clean with a damp cloth (not wet) rinsed in hot soapy water
only. Always remove plug from the mains supply before cleaning.
7. The common cause of overheating is deposits of dust or fluff in the appliance. Ensure these deposits are removed
regularly by unplugging the appliance and vacuum cleaning the air vents and grills.
8. Always unplug appliance when not in use.
9. When the appliance has been unpacked, check it for transport damage and ensure all parts have been delivered. If parts
are missing or the appliance has been damaged, contact the Goldair Customer Services Team.
10. If your appliance does not work, or is not working properly, contact the place of purchase or the Goldair Customer
Services Team.
11. Do not connect the appliance to mains supply until completely assembled and adjusted.
12. Ensure hands are dry before handling the plug or main unit.
13. Do not locate the appliance directly below any power socket outlet.
14. Ensure appliance is on a flat, stable, heat-resistant surface.
15. Do not operate with cord set coiled up as a heat build up is likely, which could be sufficient to become a hazard.
16. Carry out regular checks of the supply cord to ensure no damage is evident.
17. Do not operate this appliance with a damaged cord, plug or after the appliance malfunctions or has been dropped or
damaged in any manner. Return to a qualified electrical person for examination, electrical service or repair.
18. Do not remove plug from power socket by pulling cord; always grip plug.
19. Do not twist, kink or wrap the cord around the appliance, as this may cause the insulation to weaken and split. Always
ensure that all cord has been removed from any cord storage area and is unrolled before use.
20. It is recommended that this appliance is plugged directly into the wall socket. The use of power boards in not
recommended as many power boards are not designed to supply power to high wattage appliances.
21. A correctly specified, undamaged extension cord may be used with this appliance provided it is used in a safe manner.
22. Use this appliance only as described in this manual. Any other use is not recommended by the manufacturer and may
cause fire, electric shock or injury.
23. Do not remove plug from power socket until the appliance has been switched off.
24. Do not remove plug from power socket by pulling cord; Do not place cord under carpet or cover with rugs or furniture.
Arrange the cord so it cannot be tripped over.
25. Do not place appliance on bedding or on thick & long carpet where the openings may get blocked.
26. Switch off and allow to cool before moving.
27. Do not place appliance close to radiant heat source.
28. Never use the appliance to dry clothes.
29. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock,
fire or damage to the appliance.
30. Do not sit on the appliance.
31. Do not operate in areas where petrol, paint or other flammable liquids are used or stored.
General Care and Safety Guide

Thank you for choosing a Goldair Panel Heater. This Goldair appliance has been designed
and manufactured to high standards of engineering and with proper use and care, as
described in this booklet, will give you years of useful service. Please read these instructions
carefully and keep for future reference.
YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE
INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL.
32. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities or lack of experience and knowledge, unless they are supervised or have been given instruction concerning
the use of the appliance by a person responsible for their safety.
33. Children should be supervised to ensure that they do not play with the appliance.
34. Do not use this appliance in the immediate surrounds of a bath, a shower, or a swimming pool or other liquids. The
appliance must not be immersed in any liquids.
35. There are no user serviceable parts installed in the unit.
36. Do not place the unit in wardrobes or other enclosed spaces as this may cause fire hazards.
37. This unit is not supposed to be used in or around locations where foodstuffs, works of art or delicate articles of science,
etc are stored.
General Care and Safety Guide
WARNING!
DANGER IF SWALLOWED
Keep batteries out of reach of
children. Swallowing may lead to
serious injury or death in as little
as 2 hours due to internal burns.
If swallowed, go straight to a
hospital emergency room.
Dispose of used batteries
immediately.

SCREW PACK
8 x SCREWS including 2 x ONE
WAY SCREWS TO ATTACH
FEET
WALL MOUNTING
6 x LONG SCREWS
4 x WALL PLUGS
Components
FEET x 2
CONTROL PANEL
HEAT OUTLET
AIR INLET
REMOTE CONTROL
(BACK)
MAIN POWER SWITCH

FREE STANDING
1. Ensure the appliance is unplugged and power switches
are off.
2. Carefully turn the Main Body upside-down on a scratch-
free and stable surface. Be careful to prevent damage
to the cosmetic finish or your floor surfacing.
3. Align the screw hole on the Feet Bracket with the screw
hole on the base of the appliance.
4. Attach feet with the screws provided and ensure the
bracket sits firmly in place (do not over tighten).
5. Set appliance upright and plug into a standard 240 volt
AC electrical outlet.
Assembly and Installation
Before using this appliance, it must either be wall mounted or have the feet fitted.
The screw pack to attach the feet to your appliance will be taped to either one of the
feet for your appliance, or taped to the plug.

WALL MOUNTED
1. Make sure the appliance is unplugged and power
switches are off.
2. Position the panel appliance within one metre of
a wall socket. Do not mount in front of or below
the wall socket. Ensure there is at least 100mm
clearance on all sides of the appliance.
3. Assemble the bracket with the screws provided –
see image 1.
4. Position the mounting screws on the wall per
below mounting guide and check they are
horizontal with a spirit level. Ensure the bottom
of the heater is at least 100mm from the floor
and drill holes as required. Fix the bracket to the
wall.
5. Slot the back of the appliance onto the mounting
screws. The bottom mount is on there to keep
the heater at the correct distance from the wall.
You do not need to put a screw in the bottom
mount.
6. Plug appliance into a standard 240 volt AC
electrical outlet.
Assembly and Installation
Before using this appliance, it must either be wall mounted or have the feet fitted.
The screw pack to attach the feet to your appliance will be taped to either one of the
feet for your appliance, or taped to the plug.
NOTE: Your Goldair Panel Heater should be installed with at least 100mm clearance from the
floor and any other surrounding parts including other appliances, side walls and soft
furnishings. There must be at least 1m clearance from the top of the heater to ceilings or
shelves.
Note: Do not run the power cord behind the heater.
WALL MOUNTED HEATERS ARE ONLY TO BE MOUNTED ON WALLS THAT
COMPLY WITH CURRENT AS/NZS SPECIFICATIONS & BUILDING REGULATIONS

WARNING: Keep all objects at least 1m from the
front and 100mm from the sides of the appliance.
WARNING: In order to avoid overheating or risk of
fire, do not cover the heater.
WARNING: Never leave this appliance unattended
when in use.
WARNING: Do not use this appliance with a
programmer, remote-control system, separate
timer or any other device that switches the
appliance on automatically.
Note: When the appliance is turned on for the first
time, it may release a slight odour or smoke. This
odour or smoke is a normal occurrence caused by
the initial heating of the internal heating elements
and should not occur again.
CONTROL PANEL
1–Display
2–Up Button
3–Down Button
4–Power Button
5–Heat Setting Button
6–Timer Button
7–Receiver
8–Child Lock Button
Operating your Appliance
Always choose a safe location for the appliance, keeping in mind the safety precautions
outlined. Ensure all packaging has been removed from the unit before use.
Ensure the power switch is in the OFF position
before plugging unit in.
Do not use this heater until it is fully assembled
according to the free standing or wall mounting
instructions within this manual.
OPERATION
Plug in the unit and switch on the main power
switch. The power indicator will light up.
Press the Power button (4) to turn the unit on.The
current room temperature will be displayed.
SETTING THE TEMPERATURE
Press the Heat Setting button (5) to set the heat
level to either low or high. Press the Up (2) or Down
(3) buttons to increase or decrease the temperature.
If no buttons are pressed for 3 seconds, the heater
will run to the previously set temperature.
SETTING THE TIMER
Press the Timer button (6) to set timer. The set time
is displayed. Press the Timer button to increase the
timer in one hour increments. The timer has a range
of 0-24 hours. The unit will turn off once the timer
completes its countdown.
1
5
6
8
2
3
7
4CHILD SAFETY LOCK
Press and hold the Child Lock button for 3 seconds
to lock the system. A will be displayed.
To unlock, either turn the unit off or press and
hold the Child Lock button for 3 seconds.
TURN OFF
Press and hold the Power button (4) to turn off the
unit. The power indicator light will remain lit while
the main power switch is in the On position.

Care and Cleaning
CLEANING YOUR APPLIANCE
The appliance requires regular cleaning to ensure
trouble free operation:
Unplug the appliance from the mains supply before
cleaning.
Ensure that the appliance has been allowed to cool
down completely before cleaning.
Use a damp (not wet) cloth to wipe the exterior of
the appliance to remove dust and dirt.
Never use solutions such as benzene, thinners or
polishing agents.
Use a vacuum cleaner to remove dust and fluff from
the inlet and outlet grills.
To clean behind the appliance (when mounted on a
wall); remove unit from wall per instructions within
this booklet.
It is important to return the appliance to its original
position after cleaning and to remount on wall per
instructions within this booklet.
Ensure the appliance is dry before plugging back into
the mains supply.
Do not attempt to dismantle the appliance. There
are no user serviceable parts. For service or repair,
contact an authorised electrical service technician.
PROOF OF PURCHASE
To receive warranty retain receipt as proof of
purchase.
TECHNICAL SPECIFICATION
Model No: GGPH205
Supply: 220-240VAC 50/60Hz
Wattage: 2000W
SUPPORT AND TECHNICAL ADVICE
Goldair –New Zealand
Monday –Friday 8am-5pm
Phone [phone]
Phone [phone]
[email protected]
Goldair –Australia
Monday –Friday 8am-5pm
Phone [phone]
Phone [phone]
[email protected]
SAFETY DEVICES
This appliance has two protection devices:
1. Resettable thermal link - this will
automatically disconnect the power to the
appliance at a pre-set overheat temperature.
After cooling down it will reset and power on
again. If this occurs, investigate what is
causing the appliance to overheat.
2. Thermal fuse - this disconnects the appliance
permanently in case of overheating. (It is
non resettable).
CAUTION: The appliance generates heat during
use. Proper precautions must be taken to prevent
the risk of burns, scalds, fires or other damage to
persons.

Thank you for purchasing this Goldair product. Your product is warranted against faults and manufacture when used in normal
domestic use for a period of two years. In non-domestic use Goldair limits the voluntary warranty to three months.
Goldair undertake to repair or replace this product at no charge if found to be defective due to a manufacturing fault during the
warranty period.
This warranty excludes damage caused by misuse, neglect, shipping accident, incorrect installation, or work carried out by anyone
other than a qualified electrical service technician.
PLEASE KEEP YOUR RECEIPT AS THIS WILL HELP VERIFY YOUR WARRANTY.
The benefits given to you by this warranty are in addition to other rights and remedies available to you under law in relation to the
goods or services to which this warranty relates.
In Australia, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a
major failure.
In New Zealand this warranty is additional to the conditions and guarantees of the Consumers Guarantee Act (1993).
Two Year Warranty
Goldair Two Year Warranty (IMPORTANT: Please complete and retain this warranty card)
Name
Address
Place Of Purchase Date Of Purchase
Name Of Product Model Number
Attach a copy of the purchase receipt to this warranty card
Due to continual design improvements, the product illustrated in this User Manual may differ slightly from the actual product.
Goldair –New Zealand
CDB Goldair
PO Box 100-707
N.S.M.C
Auckland
Phone [phone]
Phone [phone]
www.goldair.co.nz
Goldair –Australia
CDB Goldair Australia Pty
PO Box 574
South Morang
Victoria, 3752
Phone [phone]
Phone 1300 GOLDAIR (1300 465 324)
www.goldair.com.au