Goldair Platinum HeatSmart Series User manual

This page has been intentionally left blank.

CAUTION: In order to avoid a hazard due to inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is regularly
switched on and off by the utility.
•This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities or lack of experience and
knowledge, unless they are supervised or have been given instruction
concerning the use of the appliance by a person responsible for their safety.
•Children should be supervised to ensure that they do not play with the
appliance.
•If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
WARNING: You must not cover this heater. Covering this heater presents
fire risk and will activate the safety fuse; permanently disabling the unit.
WARNING: Do not use this heater in small rooms when they are occupied
by persons not capable of leaving the room on their own, unless constant
supervision is provided.
WARNING: To reduce the risk of fire, keep textiles, curtains, or any
flammable material a minimum distance of 1 metre from the air outlet.
WARNING: In order to avoid overheating or fire, do not cover the heater.
General Care and Safety Guide
YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE
INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL.
•The heater must not be located immediately below a socket outlet.
•Do not use the heater if it has been dropped or damaged.
•Do not use if there are visible signs of damage to the heater.
•Ensure heater is on a flat, stable, heat-resistant surface.
•Do not use this appliance in the immediate surrounds of a bath, a shower, or a swimming
pool or other liquids.
•Keep all objects at least 1 metre from the front and 150mm from the sides of the appliance.
•This appliance is intended for household use only and not for commercial or industrial use.
•Indoor use only.
•Use only the voltage specified on the rating label of the appliance.
•Use this appliance only as described in this manual. Any other use is not recommended by
the manufacturer and may cause fire, electric shock or injury.
•The common cause of overheating is deposits of dust or fluff in the appliance. Ensure these
deposits are removed regularly by unplugging the appliance and vacuum cleaning the air
vents and grills.

•Never use the appliance to dry clothes.
•Always unplug appliance when not in use.
•Do not connect the appliance to mains supply until completely assembled and adjusted.
•Ensure hands are dry before handling the plug or main unit.
•Do not operate with cord set coiled up as a heat build up is likely, which could be sufficient to
become a hazard.
•Carry out regular checks of the supply cord to ensure no damage is evident
•Do not operate this appliance with a damaged cord, plug or after the appliance malfunctions
or has been dropped or damaged in any manner. Return to a qualified electrical person for
examination, electrical service or repair.
•Do not twist, kink or wrap the cord around the appliance, as this may cause the insulation to
weaken and split. Always ensure that all cord has been removed from any cord storage area
and is unrolled before use.
•It is recommended that this heater is plugged directly into the wall socket. Power boards are
not rated to supply power to high wattage appliances.
•A correctly specified, undamaged extension cord may be used with this heater provided it is
used in a safe manner.
•Do not remove plug from power socket until the appliance has been switched off.
•Do not remove plug from power socket by pulling cord; always grip plug.
•Do not place cord under carpet or cover with rugs or furniture. Arrange the cord so it cannot
be tripped over.
•Don’t place appliance on bedding or on thick & long carpet where the openings may get
blocked.
•Switch off and use handle provided when moving
•Do not place appliance close to radiant heat source.
•Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may
cause an electric shock, fire or damage to the appliance.
•Do not sit on the appliance.
•Do not use abrasive cleaning products on this appliance. Clean with a damp cloth (not wet)
rinsed in hot soapy water only. Always remove plug from the mains supply before cleaning.
•Do not operate in areas where petrol, paint or other flammable liquids are used or stored.
•The appliance must not be immersed in any liquids.
•There are no user serviceable parts installed in the unit.
•Do not place the unit in wardrobes or other enclosed spaces as this may cause fire hazards.
•This unit is not supposed to be used in or around locations where foodstuffs, works of art or
delicate articles of science, etc are stored.
•When the appliance has been unpacked, check it for transport damage and ensure all parts
have been delivered. If parts are missing or the appliance has been damaged, contact the
Customer Services Team.
•If your appliance does not work, or is not working properly, contact the place of purchase or
the Customer Services Team.
General Care and Safety Guide

Components
CONTROL PANEL
HEAT OUTLET
AIR INLET
CASTOR WHEELS X 4
CASTOR WHEEL BRACKETS X 2
MAIN POWER SWITCH
WALL MOUNTING
BRACKET

Assembly and Installation
Before using this appliance, it must either be wall mounted or have the castor plates
and castors fitted. The screw pack to attach the feet to your appliance will be taped to
either one of the feet for your appliance, or taped to the plug.
FREE STANDING
1. Ensure the appliance is unplugged and power switches are off.
2. Carefully turn the Main Body upside-down on a scratch-free and stable surface. Be careful
to prevent damage to the cosmetic finish or your floor surfacing.
3. Firmly press Castor Wheels onto the posts on the Castor Wheel Bracket until they click into
place. Some force may be required.
4. Align the screw hole on the Castor Wheel Bracket with the screw hole on the base of the
appliance.
5. Attach Castor Wheel Bracket with the one way screws provided and ensure the bracket sits
firmly in place (do not over tighten).
6. Return heater to the upright position.

Assembly and Installation
NOTE: Your Goldair Panel Heater should be installed with at least 150mm
clearance from the floor and any other surrounding parts including other
appliances, side walls, ceilings, shelves and soft furnishings.
WALL MOUNTED HEATERS ARE ONLY TO BE MOUNTED ON WALLS THAT
COMPLY WITH CURRENT AS/NZS SPECIFICATIONS & BUILDING REGULATIONS
Locking Screws
WALL MOUNTED
1. Make sure the heater is unplugged and power
switches are off.
2. Position the panel heater within one metre of
a wall socket. Do not mount in front of or
below the wall socket. Ensure there is at least
150mm clearance from the floor and sides of
the heater.
3. Detach the mounting bracket from the back of
the panel appliance by unscrewing the two
locking screws (located on the top of the
mounting bracket).
4. Position the mounting bracket on the wall and
mark the hole positions with a pen or pencil
and check they are horizontal with a spirit
level. Ensure the two bottom mount holes are
at least 180mm from the floor and drill holes
as required.
5. Secure the mounting bracket to the wall with
the mounting screws. (For masonry walls use
the plastic sheaths).
6. Slot the back of the appliance onto the
mounting bracket locating the bottom plugs
first and secure with two locking screws.
7. Plug appliance into a standard 240 volt AC
electrical outlet.
Note: Do not run the power cord behind the
heater.

Operating Your Heater
Always choose a safe location for the appliance, keeping in mind the safety precautions outlined.
Ensure all packaging has been removed from the unit before use. This appliance requires no
installation, it should be used solely as a portable appliance.
WARNING:In order to avoid overheating or fire, do not cover the heater.
WARNING: Keep all objects at least 1 metre from the front and 150mm from
the sides of the appliance.
WARNING: Do not use this heater with a programmer, separate timer, remote-
control system or any other device that switches the heater on automatically, since
a fire risk exists if the heater is covered or positioned incorrectly.
WARNING: Never leave this heater unattended when in use.
If mounted on castors, ensure heater is on a flat, stable, heat-resistant surface.
WALL MOUNTED HEATERS ARE ONLY TO BE MOUNTED ON WALLS THAT COMPLY
WITH CURRENT AS/NZS SPECIFICATIONS & BUILDING REGULATIONS
Once the heater is in a safe operating position and all switches are in the off
position, insert the power plug into the mains outlet.
CAUTION: Ensure the power cord is not tight because if pulled it may partially
pull the plug from the socket. A partially inserted plug will overheat the plug and
socket and could result in fire.

Operating your Appliance
1. LED display
2. On/Off button
3. Mode setting button
4. Up button
5. Down button
6. Power setting button
7. Power indicator lights
8. Comfort indicator light
9. Economy indicator light
10. Anti-frost indicator light
11. Timer indicator light
12. Auto indicator light
13. User indicator light
14. WiFi button
8910 45
11 112 13 7632
14

Operating your Appliance
Press the button. A beep will sound indicating the heater is now on and the setting will be “AUTO”
mode. The current temperature will be displayed on the screen.
To turn the heater off, press the button for at least 2 seconds until the heater switches off.
AUTO Mode
In “AUTO” mode you can set either Comfort or Economy settings as shown below. The default temperature
setting is 25oC. Set your desired temperature by pressing the UP or DOWN buttons. The screen
will return to the current temperature after a few seconds but the set temperature will be retained unless
changed by you.
Comfort mode can be set from 5 –35oC
Economy mode can be set from 5 - 31oC (this is pre-set so there is always a 4oC difference between
Comfort and Economy settings)
You may want to set the economy temperature to a much lower level than the comfort temperature and set
the heater to economy when going to bed so that the room it is in stays warm but not as hot as you would
have it if you were in the room.
The heater will automatically set the best heat setting to reach the temperature you have set and will adjust
the heat setting to maintain the temperature you have set. The blue lights will show which heat setting is
currently in use.
USER mode
Press the button to change from AUTO to USER mode. The power setting will go to high (all blue lights
illuminated). You can select the power setting you want. There are 5 levels. The blue lights will decrease
with each push. When it reaches the bottom light (lowest heat setting) the heater will then go back into
AUTO mode.
In “USER” mode you can set either Comfort or Economy settings as shown below. The default temperature
setting is 25oC. Set your desired temperature by pressing the UP or DOWN buttons. The screen
will return to the current temperature after a few seconds but the set temperature will be retained unless
changed by you.
Comfort mode can be set from 5 –35oC
Economy mode can be set from 5 - 31oC (this is pre-set so there is always a 4oC difference between
Comfort and Economy settings)
You may want to set the economy temperature to a much lower level than the comfort temperature and
set the heater to economy when going to bed so that the room it is in stays warm but not as hot as you
would have it if you were in the room.
You can set the heat setting to any of the 5 levels to heat the room. It is best to set it at the highest setting to
initially heat up the room and then set to a lower level to maintain the setting. When the room reaches the
set temperature, the element will turn off and not turn on again until the room temperature drops lower
than the set temperature.
Check that the heater main power switch is in the OFF position before plugging into the mains supply.
Turn the main power switch which is on the right hand side of the appliance just below the control panel to
the “I” position to turn the heater on.The heater will beep once and will be stand by mode.