Goldair PLATINUM GPCW100 User manual

CAUTION: In order to avoid a hazard due to inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is regularly
switched on and off by the utility.
•This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities or lack of experience and
knowledge, unless they are supervised or have been given instruction
concerning the use of the appliance by a person responsible for their safety.
•Children should be supervised to ensure that they do not play with the
appliance.
•If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
WARNING: You must not cover this heater. Covering this heater presents
fire risk and will activate the safety fuse; permanently disabling the unit.
WARNING: Do not use this heater in small rooms when they are occupied
by persons not capable of leaving the room on their own, unless constant
supervision is provided.
WARNING: To reduce the risk of fire, keep textiles, curtains, or any
flammable material a minimum distance of 1 metre from the air outlet.
General Care and Safety Guide
•Use only the voltage specified on the rating label of the appliance.
•The heater must not be located immediately below a socket outlet.
•Keep all objects at least 1 metre from the front, sides and rear of the appliance.
•This appliance is intended for household use only and not for commercial or industrial use.
•Indoor use only.
•Use this appliance only as described in this manual. Any other use is not recommended by
the manufacturer and may cause fire, electric shock or injury.
•Do not use the heater if it has been dropped or damaged.
•The common cause of overheating is deposits of dust or fluff in the appliance. Ensure these
deposits are removed regularly by unplugging the appliance and vacuum cleaning the air
vents and grills.
•Always unplug appliance when not in use.
•When the appliance has been unpacked, check it for transport damage and ensure all parts
have been delivered. If parts are missing or the appliance has been damaged, contact the
Customer Services Team.
•Do not use if there are visible signs of damage to the heater.
YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE
INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL.

•Never use the appliance to dry clothes.
•Do not connect the appliance to mains supply until completely assembled and adjusted.
•Ensure hands are dry before handling the plug or main unit.
•Ensure heater is on a flat, stable, heat-resistant surface.
•Do not operate with cord set coiled up as a heat build up is likely, which could be sufficient to
become a hazard.
•Carry out regular checks of the supply cord to ensure no damage is evident
•Do not operate this appliance with a damaged cord, plug or after the appliance malfunctions
or has been dropped or damaged in any manner. Return to a qualified electrical person for
examination, electrical service or repair.
•Do not twist, kink or wrap the cord around the appliance, as this may cause the insulation to
weaken and split. Always ensure that all cord has been removed from any cord storage area
and is unrolled before use.
•It is recommended that this heater is plugged directly into the wall socket. Power boards are
not rated to supply power to high wattage appliances.
•A correctly specified, undamaged extension cord may be used with this heater provided it is
used in a safe manner.
•Do not remove plug from power socket until the appliance has been switched off.
•Do not remove plug from power socket by pulling cord; always grip plug.
•Do not place cord under carpet or cover with rugs or furniture. Arrange the cord so it cannot
be tripped over.
•Don’t place appliance on bedding or on thick & long carpet where the openings may get
blocked.
•Switch off and use handle provided when moving
•Do not place appliance close to radiant heat source.
•Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may
cause an electric shock, fire or damage to the appliance.
•Do not sit on the appliance.
•Do not use abrasive cleaning products on this appliance. Clean with a damp cloth (not wet)
rinsed in hot soapy water only. Always remove plug from the mains supply before cleaning.
•Do not operate in areas where petrol, paint or other flammable liquids are used or stored.
•Do not use this appliance in the immediate surrounds of a bath, a shower, or a swimming
pool or other liquids.
•The appliance must not be immersed in any liquids.
•There are no user serviceable parts installed in the unit.
•Do not place the unit in wardrobes or other enclosed spaces as this may cause fire hazards.
•This unit is not supposed to be used in or around locations where foodstuffs, works of art or
delicate articles of science, etc. are stored.
•If your appliance does not work, or is not working properly, contact the place of purchase or
the Customer Services Team.
General Care and Safety Guide

The remote control supplied with this heater uses a CR2025 coin type battery (Included).
DANGER IF SWALLOWED
Keep batteries out of reach of children. Swallowing may lead to serious injury or death in as
little as 2 hours due to internal burns.
If swallowed, go straight to a hospital emergency room.
Dispose of used batteries immediately.
YOUR SAFETY IS IMPORTANT TO US. PLEASE ENSURE YOU TAKE NOTE OF THE
INSTRUCTIONS AND WARNINGS OUTLINED IN THIS MANUAL.
General Care and Safety Guide
WARNING!
DANGER IF SWALLOWED
Keep batteries out of reach of
children. Swallowing may lead to
serious injury or death in as little
as 2 hours due to internal burns.
If swallowed, go straight to a
hospital emergency room.
Dispose of used batteries
immediately.

Components
SCREWS:
2 X EXPANDING SCREW PIPES
2 X SCREWS
MAIN BODY X 1
REMOTE X 1
NOTE: Before using this appliance, it must be wall mounted. The screw
pack to mount the appliance to the wall will be taped to the plug.
NOTE: Your Goldair Ceramic Wall Heater should be installed with at least
1.8m clearance from the floor at least 300mm clearance form the ceiling and
200mm clearance from any other surrounding parts including other
appliances, side walls, shelves and soft furnishings.
NOTE:Do not run the power cord behind the heater.
WALL MOUNTED HEATERS ARE ONLY TO BE MOUNTED ON WALLS THAT
COMPLY WITH CURRENT AS/NZS SPECIFICATIONS & BUILDING REGULATIONS
Installing your Appliance

TOOLS REQUIRED
✓Drill
✓Hammer
✓Phillips head screwdriver
✓Spirit Level
LOCATION
The appliance should be placed with a minimum distance
of 1 metre between the unit and flammable objects such
as curtains, paintings or other materials that may pose fire
risk.
Installation of the appliance on the wall MUST BE 1.8m
above the floor.
Installation of the appliance on the wall MUST BE 20cm
away from closest side wall.
Installation of the appliance on the wall MUST BE 30cm
from the ceiling.
WARNING: Do not mount directly under or
over an electrical power socket; it is
recommended to install the appliance to the
side of the power socket.
The appliance is designed to be installed 1.8m
above the floor. As the cord length is 1.5m, an
electrician may be required to install a power
socket nearer to the appliance.
INSTALLATION
1. Drill two holes on the wall allowing 1.8metres
between floor and bottom of appliance and 20cm
from side wall to side of appliance.
2. Measure the distance between the mounting holes
on the back of the appliance and then mark the wall
at the measured distance. Ensure that the marks you
make are level.
3. Be sure to make the hole diameter the same as the
expanding screw pipe.
4. Place the expanding screw pipe into the hole in the
wall and then fix two screws on the expanding pipe.
5. Keep the tips of the screws out approximately 10mm,
and hang the appliance.
6. Ensure that the screws are held in firmly enough to
hold the weight of the appliance.
7. Slide the appliance across to the right and then down,
locking the appliance mounting bracket to the screws
in the wall.
Installing your Appliance

Operating Your Heater
Always choose a safe location for the appliance, keeping in mind the safety precautions
outlined. Ensure all packaging has been removed from the unit before use.
WARNING: In order to avoid overheating or fire, do not cover the heater.
WARNING: Keep all objects at least 1 metre from the front, sides and rear of
the appliance.
WARNING: Do not use this heater with a programmer, separate timer,
remote-control system or any other device that switches the heater on
automatically, since a fire risk exists if the heater is covered or positioned
incorrectly.
WARNING:Never leave this heater unattended.
Ensure heater is on a flat, stable, heat-resistant surface.
Once the heater is in a safe operating position and all switches are in the off
position, insert the power plug into the mains outlet.
CAUTION: Ensure the power cord is not tight because if pulled it may
partially pull the plug from the socket. A partially inserted plug will overheat
the plug and socket and could result in fire.
HEATER CONTROL PANEL
•Turn the Power Switch at the side of the appliance to the “I” position.
•Press the Power Button (ON/OFF) on the remote control to turn the appliance on, You
will hear a beep. The unit will start in Fan Only mode and begin to blow out room
temperature air. For best results, aim the remote directly at the remote sensor on the
front panel of the appliance. The remote has a 3 metre range of operation.
•The LED will display the current room temperature
1.
4.
3.
2.
TOUCH CONTROL PANEL
1. Timer Indicator 3. Temperature/Time Indicator
2. High/Low Heat Mode 4. Fan Only Mode

•Press the Power Button again to switch from Fan Only mode to Low Heat mode.
•You will hear a beep, and 1 High/Low Heat mode bar will illuminate on the control panel.
•Press the Power Button again to switch from Low Heat mode to High Heat mode.
•You will hear a beep, and 2 High/Low Heat mode bars will illuminate on the control panel.
•If you press the Power Button a fourth time, you will hear a beep, and the louvre will operate automatically.
•Pressing the Power Button again will turn the appliance OFF.
NOTE: The appliance will continue to operate for an additional 30 seconds in the Fan mode after the unit has
been switched off. This is normal. This will help cool the internal components down and prolong the life of the
unit.
To switch between the operating modes press the MODE button.
Press the “˄” button to increase the temperature.
Press the “˅” button to decrease the temperature.
Temperature range: 5 to 35 degrees.
Operating Your Heater
Always choose a safe location for the appliance, keeping in mind the safety precautions
outlined. Ensure all packaging has been removed from the unit before use.
REMOTE CONTROL
1. Power Button (ON/OFF)
2. Timer Button
3. Mode Selection Button
4. Increase Time/Temperature
5. Decrease Time/Temperature
1.
2.
5.
4.
3.

TIMER
Press the TIMER button to use timer function.
Press the “˄” button to increase the length of time before the unit switches off.
Press the “˅” button to decrease the length of time before the unit switches off.
Timer range: 1 to 24 hours in 1 hour increments.
After the desired set time has displayed on the control panel, the set time will flash before the control panel
goes back to display the current room temperature. The Timer icon will remain displayed on the control panel.
To switch the Timer off, press the TIMER button again.
Press the POWER button to turn the device OFF.
NOTE: If the device is operating, pressing the POWER button for the first time activates the louvres’ vertical
movement mode, pressing it for the second time turns this mode off, and pressing the button for the third time
turns the appliance off.
Operating Your Heater
REMOTE CONTROL
1. Power Button (ON/OFF)
2. Timer Button
3. Mode Selection Button
4. Increase Time/Temperature
5. Decrease Time/Temperature
1.
2.
5.
4.
3.
1.
4.
3.
2.
TOUCH CONTROL PANEL
1. Timer Indicator 3. Temperature/Time Indicator
2. High/Low Heat Mode 4. Fan Only Mode

SUPPORT AND TECHNICAL ADVICE
Goldair –New Zealand
Monday –Friday 8am-5pm
Phone [phone]
Phone [phone]
[email protected]
Goldair –Australia
Monday –Friday 8am-5pm
Phone [phone]
Phone [phone]
[email protected]
TECHNICAL SPECIFICATION
Model No:GPCW100
Supply: 220-240VAC 50Hz
Wattage: 2000W
Operating Your Heater
SAFETY DEVICE
•Resettable Thermal Link - this will automatically disconnect the power to the
appliance at a pre-set overheat temperature. After cooling down it will reset and
power on again. If this occurs, investigate what is causing the appliance to overheat.
•For example, if the louvres become covered by an obstacle such as a curtain. If this
occurs, disconnect the appliance from the mains, wait for about 30 minutes to let it
cool down and remove the obstacle.
•After 30 minutes, turn on the appliance to the desired mode. It should start
normally. If the appliance does not work correctly, please contact your nearest
service centre.
CAUTION: Do not attempt to dismantle the appliance. There are no user
serviceable parts. For service or repair, contact an authorised electrical service
technician.
CAUTION: The heater generates heat during use. Proper precautions must
be taken to prevent the risk of burns, scalds, fires or other damage to persons.
CARE AND CLEANING
•The heater requires regular cleaning to ensure trouble free operation:
•Unplug the heater from the mains supply before cleaning.
•Ensure that the heater has been allowed to cool down completely before cleaning.
•The common cause of overheating is deposits of dust or fluff in the appliance. Ensure
these deposits are removed regularly by unplugging the appliance and vacuum
cleaning the air vents and grills.
•Use a damp cloth (not wet) to wipe the exterior of the heater to remove dust and
dirt.
•Never use solutions such as petrol, thinners or polishing agents.
•Ensure the heater is dry before plugging back into the mains supply.
PROOF OF PURCHASE
To receive warranty retain receipt as proof of purchase.

Thank you for purchasing this Goldair Platinum product. Your product is warranted against faults and manufacture when used in
normal domestic use for a period of three years. In non-domestic use Goldair limits the voluntary warranty to three months.
Goldair undertake to repair or replace this product at no charge if found to be defective due to a manufacturing fault during the
warranty period.
This warranty excludes damage caused by misuse, neglect, shipping accident, incorrect installation, or work carried out by anyone
other than a qualified electrical service technician.
PLEASE KEEP YOUR RECEIPT AS THIS WILL HELP VERIFY YOUR WARRANTY.
The benefits given to you by this warranty are in addition to other rights and remedies available to you under law in relation to the
goods or services to which this warranty relates.
In Australia, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a
major failure.
In New Zealand this warranty is additional to the conditions and guarantees of the Consumers Guarantee Act (1993).
Three Year Warranty
Goldair Three Year Warranty (IMPORTANT: Please complete and retain this warranty card)
Name
Address
Place Of Purchase Date Of Purchase
Name Of Product Model Number
Attach a copy of the purchase receipt to this warranty card
Due to continual design improvements, the product illustrated in this User Manual may differ slightly from the actual product.
Goldair –New Zealand
CDB Goldair
PO Box 100-707
N.S.M.C
Auckland
Phone [phone]
Phone [phone]
www.goldair.co.nz
Goldair –Australia
CDB Goldair Australia Pty
PO Box 574
South Morang
Victoria, 3752
Phone [phone]
Phone 1300 GOLDAIR (1300 465 324)
www.goldair.com.au