Golight GOBEE 2151 User manual

IMPORTANT SAFETY INFORMATION
* This symbol is to alert you to important operating or servicing
instructions that appear in your instructions. Always follow
basic safety precautions when using this product to reduce the
risk of injury, fire or electric shock.
*This light is for off-road and utility use only. It is not designed
for road use as a driving light.
*The Gobee™ compiles with Part. 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) The light and
remote may not cause harmful interface, and (2) this light and
remote must accept any interference, including interference that
may cause undesired operation
FCC RULE Part. 15.21—Changes or modifications made by the
user not expressly approved by Golight, Inc. for compliance
could void the users authority to operate the equipment.
For safe and efficient operation of your Golight® Gobee™,
observe these guidelines:
Using your Gobee™ in icing conditions could damage the gear
motors.
Your Golight® Gobee™ is a radio transmitter and receiver oper-
ating at 433 MHZ. Whenever the light is on the internally
mounted antenna sends out and receives radio frequency (RF)
energy.
Modern electronic equipment, i.e. Personal medical
devices such as pacemakers, hearing aids, etc. are shielded from
RF energy. However, RF energy may effect some electronic
equipment.
Vehicle electronic systems may be effected by RF
energy. Check with your vehicle manufacturer reprehensive to
be sure that your Gobee™ will not effect the electronic system of
your vehicle
* Notice : The changes or modifications not expressly approved
by the party responsible for compliance could void the user’s
authority to operate the equipment.
* IMPORTANT NOTE: To comply with the FCC RF exposure
compliance requirements, no change to the antenna or the device
is permitted. Any change to the antenna or the device could result
in the device exceeding the RF exposure requirements and void
user’s authority to operate the device.
GOBEE™
Model 2151
Congratulations
You are now the owner of one of the finest remote
control searchlightsavailable today. Thank you
for letting Golight® assist you inyour lighting
applica-tion needs. We’re proud ofour products
and the technology that we have developed to
ensure our customers the most durable, versatile
and powerful searchlights in the industry.
Please read these instructions before using your new
Golight® Gobee™
The Golight® Gobee™ 2151is designed to be used
in your existing 2 or 3 prong bow socket. This
searchlight with directional flexibility is controlled
by a wireless remote, which gives the operator a full
360° horizontal rotation and a 90° vertical tilt with
fingertip control.
The Gobee™ Includes:
Gobee™ Searchlight
- Mounted on 12” stanchion with 12 volt
NavDC igatio Lighn ts.
Programmable Remote Control w/ battery
Lined Nylon Storage Bag
INSTALLATION:
EXISTING BOW MOUNT SOCKET
1) Carefully engage stanchion into base socket. As
it slides into socket, make sure the alignment
screw at rear of stanchion slides into notch at
rear of socket. Push stanchion down until it en-
gages with electrical connector at bottom of
socket. Lock unit in place by sliding lock collar
into the top of the socket and rotate clockwise.
Check to make sure stanchion is secure in the
socket .
2) This light has been designed to function in a 2 or
3 pin bow socket. There is a rocker switch on
the bottom of the spotlight assembly that is used
to cycle between 2 and 3 pin wiring configura-
tions. The red/green navigation light will turn on
when the switch is in the correct position for
your boats wiring configuration.
NOTE: The boat’s bow socket is typically on a
“switched” circuit. Please make sure this circuit
is powered on when trying to use the light.

BULB REPLACEMENT
The Golight® Gobee™ utilizes a H-3 55 watt bulb.
TROUBLESHOOTING YOUR GOBEE™
Power requirements: This product requires a mini-
mum voltage of 12V and requires at least 5.5—6
amps to function. 7 amp fuse recommended.
If the power receptacle is wired correctly and the
light will still not activate with the remote, the boat
wire may not be the recommended gauge. Golight
Inc. recommends a minimum of 14 gauge wire; 16
gauge may or may not be sufficient depending on
the total length of wire.
BATTERY INSTALLATION AND REMOVAL
FOR TRANSMITTER
Remove battery cover by unscrewing phillips head
screw. With battery compartment now exposed,
insert battery with “+” side up. To remove battery,
gently grasp outer edge of battery and lift it up.
Replace battery cover and tighten Phillips head
screw.
PROGRAMMABLE REMOTE
INSTRUCTIONS
The Golight® Gobee™ is controlled with a
programmable remote with 16 different channels.
This feature allows you the freedom to change the
channel selection, and the receiver relearns the new
selection.
PROGRAMMING THE TRANSMITTER
This light has been pre-programmed at the factory,
and it is not necessary to re-program the transmitter,
unless you experience outside interference.
1. IMPORTANT: Remove from base socket.
2. Remove battery cover from remote control
3. Set the 4 dip switches to a selection of your
choice. There are 2 positions on each; use a
small screwdriver and select a position for each
dip switch.
4. Replace battery cover
5. Depress the on/off button and keep it held
down.
6. While holding the on/off button down, reinstall
the power to the unit (replace Gobee™ into
base socket)
7. Keep your finger on the on/off button for 5-6
seconds, and then release. The light should
now be reprogrammed.
OPERATION OF GOLIGHT® GOBEE™
1. Using the remote control, turn on the light by
depressing the on/off button.
2. With the 4 way arrows on the remote control,
rotate your light to the desired location. De-
pending on the conditions, the wireless remote
may be used up to 15 feet from the Gobee™.