golmar VESTA7 GB2 User manual

Code 50121960 TVESTA G 2 EN7 B REV.0 12 7
VESTA G 2 M7 ONITORB
USER MANUAL
C m ra/a e
Door panel Light Intercom About Settings
TECHNOLOGY

INTRODUCTION
First and foremost we would like to thank you for purchasing this product.
Our commitment to achieving the satisfaction of customers like you is manifested through our ISO-9001 certification
and the manufacture of products like the one you have just purchased.
Its advanced technology and strict quality control will ensure that customers and users enjoy the numerous features
that this device offers. To get the most out of them and ensure proper operation from day one, we recommend that you
read this instruction manual.
CONTENTS
2
SAFETY PRECAUTIONS
-Avoid overtightening the screws of the monitor's wall mounting connector.
-Always disconnect the power supply before making modifications to the device.
-The fitting and handling of these devices must be carried out by .authorised personnel
-All of the wiring must run at least 40cm away from any other wiring.
-Install the monitor in a dry protected location free from the risk of dripping or splashing water.
-Do not place in humid, dusty or smoky locations, or near sources of heat.
-Before connecting the system to the mains, check the connections between the door panel, power supply, distributors
and monitors.
-Always follow the instructions contained in this manual.
Introduction................................................................................................................................................................... .2.
Contents....................................................................................................................................................................... .2. .
Safety precautions.......................................................................................................................................... ..2.............. .
Characteristics.............................................................................................................................................................. .3.
System operation.......................................................................................................................................... .3................. .
Description of the monitor........................................................................................................................................... .......
................................................................................................................................................................. .4. .
Description
................................................................................................................................ . 4......... .Function and menu buttons
............................................................................................................................................... 4.....Connection terminals
............................................................................................................................... . 4.............. .Configuration DIP switch
........................................................................................................... 5...................Setting the monitor's address codes
Installing the monitor in a wall mounting connector......................................................................................................... 6..
Installing the monitor in an embedding box.................................................................................................................... . 7. .
Operation........................................................................................................................................................... ...............
.......................................................... 8..
Description and communication with hearing aids (Vesta7 GB2/H monitor only)
1.1 ........................................................................................................................ 8.Receiving a call from the door panel
1.2 ......................................................................................................... .9..................... .Call not answered (missed call)
1.3 ............................................................................................................................ .9.Ending a call from the door pane
1.4 ....................................................................................................................... 9Answering a call from the door panel
Monitor screen and volume settings menu (brightness, colour, contrast and communication volume).......................... 10...
User direct access functions..................................................................................................................... .11.................... .
1. ............................................................................................................ . 11-12.. .
Displaying door panel/camera images
2. ......................................................................................................................................12Activating the outdoor light
3. ............................................................................................................................. 13..Activating 'Do not disturb' mode
4. ........................................................................................................... .13-14.................Intercom within an apartment
User menu............................................................................................................................................................. ...........
.................................................................................................................................................. 15..
Accessing the menu
1. ................................................................................................................. . 16.. .Displaying door panel/camera images
2. ......................................................................................................................................17.Activating the outdoor light
3. ................................................................................................................... .17-18....... .Intercom between apartments
4. ................................................................................................................................................... . 18. .Exiting the menu
5. ....................................................................................................... ..19-20...... .About (information and installer setup)
6. ............................ .20-22....................... .Settings (ringtone, ringtone volume, default settings and language selection)
Cleaning the monitor................................................................................................................................................. .22... .
Notes............................................................................................................................................................................23
VESTA7 G 2 MONITORB

CHARACTERISTICS
-Hands-free monitor.
-7” TFT colour screen.
-Monitor with simple installation (non-polarised 2 wire BUS).
-The VESTA7 GB2/H monitor interacts with hearing aids equipped with T-mode, making conversation between the
door panel and apartment easier.
-Capacitive function buttons to access and select menu functions:
User menu:
-Displaying the door panel image.
-Displaying the camera image (DQ-CAM-GB2 module required).
-Activating the outdoor light.
-Intercom between apartments.
-About: Information and access to installer setup.
-Settings: Ringtone, ringtone volume, default settings (restore) and language.
Installer setup:
-Monitor as master or slave 1, slave 2 or slave 3. Up to 4 monitors per apartment.
-Indicating the number of door panels (up to 4 access panels).
-Indicating the number of cameras (up to 4 CCTV cameras, DQ-CAM-GB2 module required).
-Enabling the menu to be viewed when the Bus is busy.
-Activating intercom between apartments.
Screen and volume settings menu: (during auto switch-on or communication).
- .Brightness
-Colour.
-Contrast.
-Monitor speaker volume (communication).
-Start/stop communication button and, in standby mode, it displays the image from the door panel.
-Door release button 1 / in standby, it activates the outdoor light.
-Door release button 2 / in standby, it activates/deactivates the 'do not disturb' function.
-Intercom within apartment button.
-Menu access button.
-Monitor status LEDs.
-Different ringtones to identify the origin of the call (door panel, intercom or apartment door).
-DIP switches for setting the monitor address (call code) and end of line.
-Input for call from the apartment door.
-SAR-12/24 call repeater output (12Vdc/50mAmaximum).
SYSTEM OPERATION
-To make a call, the visitor must press the button of the apartment; an audible sound indicates that the call is being
made and LED will turn on. If vocal synthesis is enabled, a 'Call is in progress' message appears indicating that a
call is being made. At this moment, the apartment's monitors receive the call. If another apartment is called by
mistake, press the button for the correct apartment and the first call will be cancelled.
-The ring tone lasts for 40 seconds. Without alerting the visitor, their image appears on the master monitor during this
time. To view the picture on a slave monitor this function must first be activated in the monitor. :House kit application
the image appears on the monitor (with code 0 “apartment 1” or monitor with code 16 if the call is in “apartment 2”)
when receiving the call without the visitor being alerted.
If the call is not answered within 40 seconds, LED will turn off and the channel will be freed.
-To establish communication, press button on any monitor in the apartment. Door panel LED will turn on.
If the monitor is a VESTA7 GB2/H with icon on the front, make sure that the hearing aid is 20 cm away from the
monitor to ensure maximum audio quality during communication with the door panel.
-Communication will last for one and a half minutes or until button or is pressed again. When communication
has finished, LEDs and will turn off and the channel will be freed. If vocal synthesis is activated, a 'Communication
is finished' message will indicate that the call is over.
-To open door 1 or 2, press the corresponding button / during the call or communication processes: one press
will activate the lock release for five seconds and LED will also turn on for five seconds. If vocal synthesis is enabled,
a 'Door Opened!' message will be indicated on the door panel.
-Descriptions of the function pusg buttons can be found on p. 4.
3
VESTA7 G 2 MONITORB

DESCRIPTION OF THE MONITOR
Connection terminals and DIP switch:
( ):WHITE HZ+
( ):GREEN HZ-
Connection terminals:
L1, L2: Bus connection (non-polarised).
HZ+, HZ-: Door bell connection.
CALL REPEATER, GND: Call repeater connection (SAR-12/24).
(12Vdc/50mAmaximum).
Configuration DIP switch:
DIP6: Sets the end of line. Set to ON in monitors where the bus
cable terminates. Set to OFF only in intermediate monitors.
DIP1 to DIP5: To set the monitor address (addresses 0 to 31).
The switches set to OFF have a zero value.
The values of the switches set to ON are shown in the table below.
The monitor code is the sum of the values of the switches set to
ON.
123
ON DIP
456
L1
L2
(R ):ED CALL REPEATER
( ):BLACK GND
( ):YELLOW DO NOT USE
Menu entry and user settings button. On menu screen: Display door panel image.
On menu screen: Intercom function between
apartments.
Menu buttons:
4
123
ON DIP
4 5 6
Example: 0 + 0+4 + 0 +16 = 20
Switch number: 1 2 3 4 5
1 2 4 8 16
Value when ON:
Value chart
Menu screen exit and selection button.
Menu entry and selection button.
VESTA7 G 2 MONITORB
a. 7” TFT colour screen.
b. Microphone.
c. Start/stop communication button.
In standby: Display door panel image.
d. Door release button 1. In standby: Activate out light..
e. Door release button 2. In standby: 'do not disturb' mode,
if the mode is activated, the icon illuminates.
f...End call/communication button.
In standby, intercom within apartment function.
In auto spy/auto switch-on: Select other door panel(s),
camera(s) in descending mode and in carousel (if any).
g. ( )In standby: Enter menu. continued
In auto spy/auto switch-on: Select other door
panel(s), camera(s) in ascending mode and in
carousel (if any).
In call/communication: select camera(s) in ascending
mode and in carousel (if any).
h. In standby: enter menu.
Video activated: screen and communication
volume settings.
i. Vertical wiring entry.
j. Connector fixings.
k. Configuration DIP switch.
l. Connector.
m.Bus connection terminals.
n. Communication with hearing aids (Vesta7 GB2/H only)
Set the hearing aid switch to T-mode, see p. 8.
l
m
j
k
b
cfg
a
de
1 2 3
ON DIP
4 5 6
h
i
j
i
On menu screen: Activate outdoor light.
123
ON DIP
456
n

5
DESCRIPTION OF THE MONITOR
VESTA7 G 2 MONITORB
Setting the monitor's address codes (addresses 0 to 31):
DIP6: Sets the end of line. Set to ON in monitors where the video cable terminates. Set to OFF only in intermediate
monitors.
1 2 3
ON DIP
4 5 6
Co 0 / 32de
123
ON DIP
4 5 6
Co 01de
123
ON DIP
4 5 6
Co 02de
123
ON DIP
4 5 6
Co 03de
123
ON DIP
4 5 6
Co 04de
123
ON DIP
4 5 6
Co 05de
123
ON DIP
4 5 6
Co 06de
123
ON DIP
4 5 6
Co 07de
1 2 3
ON DIP
4 5 6
Co 08de
123
ON DIP
4 5 6
Co 09de
123
ON DIP
4 5 6
Co 10de
123
ON DIP
4 5 6
Co 11de
123
ON DIP
4 5 6
Co 12de
123
ON DIP
4 5 6
Co 13de
123
ON DIP
4 5 6
Co 14de
123
ON DIP
4 5 6
Co 15de
123
ON DIP
4 5 6
Co 16de
123
ON DIP
4 5 6
Co 17de
123
ON DIP
4 5 6
Co 18de
123
ON DIP
4 5 6
Co 19de
123
ON DIP
4 5 6
Co 20de
123
ON DIP
4 5 6
Co 21de
123
ON DIP
4 5 6
Co 22de
123
ON DIP
4 5 6
Co 23de
123
ON DIP
4 5 6
Co 24de
123
ON DIP
4 5 6
Co 25de
123
ON DIP
4 5 6
Co 26de
123
ON DIP
4 5 6
Co 27de
123
ON DIP
4 5 6
Co 28de
123
ON DIP
4 5 6
Co 29de
123
ON DIP
4 5 6
Co 30de
123
ON DIP
4 5 6
Co 31de
DIP1 to DIP5: To set the monitor address (addresses 0 to 31).
123
ON DIP
4 5 6
Dip6 ONto Dip6 OFFto
123
ON DIP
4 5 6
( )
**
( )
** Important:
-In door panel systems with call pushbuttons, the first address on the monitor is 'Code 0'.
-In coded panel systems (N3301/GB2), 'Code 0' is 'Code 32', which means that when a call is made to a monitor with
'Code 0' (DIP 1 to DIP 5 set to OFF), needs to be entered on the N3301/GB2 numeric keypad.
-In the software (Address Manager GB2), 'Code 0' is also shown as 'Code 32'.
23

INSTALLING THE MONITOR IN A WALL MOUNTING CONNECTOR
The top of the connector must be positioned at a height of 1.60m. The minimum distance between the sides of the
connector and the closest object must be 5cm.
Positioning the wall mounting connector:
Fix the monitor's wall mounting connector to the wall by drilling two 6mm diameter holes and using the screws and plugs
supplied with the monitor.
Fixing the monitor's wall mounting connector to the wall:
Positioning the monitor:
1 2 3
Avoid dusty or smoky environments or locations near sources of heat.
6
Connect the cables to the monitor (see p. 4), position the monitor in front of the wall mounting connector, ensuring that
the holes in the base of the monitor line up with those on the connector , and then move the monitor
downwards until the monitor is securely fixed to the connector .
Remember to remove the protective covering from the front of the monitor once installation is complete.
1
23
1 6. 0m
VESTA7 G 2 MONITORB
x4 30

INSTALLING THE MONITOR IN AN EMBEDDING BOX
Make a hole in the wall to position the top of the universal embedding box at a height of 1.60 m from the ground. The
minimum distance between the sides of the embedding box and the closest object must be 5cm.
Positioning the embedding box:
1 6. 0m
Pass the cable through the hole made in the embedding box. Embed the box and ensure that it is level and flush.
Fix the wall mounting connector of the monitor to the embedding box with the screws supplied.
Positioning the embedding box and fitting the wall mounting connector:
Avoid dusty or smoky environments or locations near sources of heat.
Screws supplied with
the embedding box.
7
VESTA7 G 2 MONITORB
Positioning the monitor:
1 2 3
Connect the cables to the monitor (see p. 4), position the monitor in front of the wall mounting connector, ensuring
that the holes in the base of the monitor line up with those on the connector , and then move the monitor
downwards until the monitor is securely fixed to the connector .
Remember to remove the protective covering from the front of the monitor once installation is complete.
1
23

OPERATION
When a call is received, the monitor(s) will play a melody, the LEDs will illuminate (the LED of button will blink
rapidly) and the image from the door panel will be displayed on the master monitor without the visitor knowing. If the
call is not answered within 40 seconds the monitor returns to standby mode.
1.1 Receiving a call from the door panel:
Monitor description when receiving a call and during communication:
To open door 1, press the door release button during the call: one press will activate the lock release for 5
seconds.
8
Continued overleaf
DS-1
VESTA7 G 2 MONITORB
00:30
01
Start/stop communication.
Call: LED blinks rapidly.
Communication: LED blinks slowly.
Door panel that made the call/
CCTV camera selected.
Elapsed call/communication time.
In call.
Screen settings: brightness, colour,
contrast and monitor volume.
Select CCTV camera(s) image.
(DQ-CAM-GB2 module required).
End call/communication.
Activate lock release 2.
Activate lock release 1.
In communication.
In call/communication LEDs illuminated.
00:30
01
To open door 2, press the door release button during the call: one press will activate the lock release for 5
seconds.
Communication with hearing aid.
Note: Set the hearing aid switch to T-mode.
(Vesta7 GB2/H only).
T
Communication with hearing aid (Vesta7 GB2/H monitor only):
Make sure that the hearing aid is 20 cm away from the
monitor to ensure maximum audio quality during
communication with the door panel.

OPERATION
When a call is received, the monitor(s) will play a melody, the LEDs will illuminate (the LED of button will blink
rapidly) and the image from the door panel will be displayed on the master monitor without the visitor knowing. To end
the call, press button .
To open door 1 or 2, press the corresponding button / during the call process: one press will activate lock
release 1 or 2 for five seconds.
1.3 Ending a call from the door panel:
Continued from previous page.
1.2 Call not answered (missed call):
To open door 1, press the door release button
during the call: one press will activate the lock
release for 5 seconds.
9
1.4 Answering a call from the door panel:
When a call is received, the monitor(s) will play a melody, the LEDs will illuminate (the LED of button will blink
rapidly) and the image from the door panel will be displayed on the master monitor without the visitor knowing. To
answer the call, press button (the LED of button will blink slowly). If the monitor is a VESTA GB2/H with
icon on the front, make sure that the hearing aid is 20 cm away from the monitor to ensure maximum audio quality
during communication with the door panel.
Communication will last for one and a half minutes or until button or is pressed again.
To open door 1 or 2, press the corresponding button / during the call or communication processes: one press
will activate lock release 1 or 2 for five seconds.
Start/stop communication.
VESTA7 G 2 MONITORB
00:30
DS-1
00:30
DS-1
00:30
01
When a call is received, the monitor(s) will play a melody, the LEDs will illuminate (the LED of button will blink
rapidly) and the image from the door panel will be displayed on the master monitor without the visitor knowing. If the
call is not answered within 40 seconds the monitor returns to standby mode.
To open door 2, press the door release button
during the call: one press will activate the lock
release for 5 seconds.
To open door 1, press the door release button
during the call: one press will activate the lock
release for 5 seconds.
To open door 2, press the door release button
during the call: one press will activate the lock
release for 5 seconds.
00:30
DS-1
00:30
DS-1
00:30
01
DS-1
00:30
DS-1
00:30
01
End call.

SCREEN AND VOLUME SETTINGS MENU
10
To adjust brightness, the monitor must be in communication or auto switch-on mode. Then press button to
display option . Using menu buttons and , select the required brightness level. Press button to change the
following option or press to exit the settings menu.
To adjust the colour, the monitor must be in communication or auto switch-on mode. Then press button repeatedly
until option is displayed on the screen. Using menu buttons and , select the required colour level. Press
button to change the following option or press to exit the settings menu.
To adjust the contrast, the monitor must be in communication or auto switch-on mode. Then press button repeatedly
until option is displayed on the screen. Using menu buttons and , select the required contrast level. Press
button to change the following option or press to exit the settings menu.
To adjust the communication volume, the monitor must be in communication or auto switch-on mode. Then press
button repeatedly until option is displayed on the screen. Using menu buttons and , select the required
volume level. Press button to return to option or press to exit the settings menu.
VESTA7 G 2 MONITORB
00:01
01
5
+
-
-
00:01
01
5
+
-
-
00:01
01
5
+
-
-
00:01
01
6
+
-
-

USER DIRECT ACCESS FUNCTIONS
Description of buttons with user direct access functions:
VESTA7 G 2 MONITORB 11
Display door panel image.
Activate/deactivate 'Do not disturb' mode function.
Activate intercom function within apartment.
Activate outdoor light.
1. Displaying door panel/camera images:
1.1 To display the image from one of the installed door panels/cameras, press button while the monitor is in
standby. The following screen will display the image from the door panel with address 1, indicating the selected door
panel '01' and the elapsed connection time.
Monitor in standby
00:01
01
Door panel selected
Continued overleaf

To establish audio and video communication with the selected door panel, press button . The screen will
display symbol . Communication will last for one and a half minutes or until button is pressed again.
During door panel selection, door 1 and 2 can be opened by pressing the corresponding button / during the
image display or communication processes: one press will activate lock release 1 or 2 for five seconds.
Then, using menu buttons and , select the required door panel/camera (DQ-CAM-GB2 module required) in
descending and ascending mode respectively (carousel mode).
The connection will last for 30 seconds or until option is pressed twice if a door panel is selected or once if a camera
is selected.
During door panel selection, door 1 and 2 can be opened by pressing the corresponding button / : one press will
activate lock release 1 or 2 for five seconds.
Continued overleaf
00:01
01
00:01
01
Door panel selected
00:01
01
Camera selected
Continued from previous page.
USER DIRECT ACCESS FUNCTIONS
VESTA7 G 2 MONITORB 12
2. Activating the outdoor light:
2.1 To activate the outdoor light, press button while the monitor is in standby. The outdoor light (SAR-GB2
module required) activates for 1 minute. See the “TSAR-GB2 ML”user manual for how to set other light activation
times.
Monitor in standby

3.1 To activate 'Do not disturb' mode, press button / on the master monitor while in standby. The status LED
of button / of the master and secondary monitors in the apartment will illuminate indicating that the function is
activated. The monitors in the apartment will not receive door panel or intercom calls.
Continued overleaf
Continued from previous page.
USER DIRECT ACCESS FUNCTIONS
VESTA7 G 2 MONITORB 13
Monitor in standby
3Activating 'Do not disturb' mode:
3.2 To deactivate 'Do not disturb' mode, press button / on the master monitor while in standby. The status
LED of button / of the master and secondary monitors in the apartment will turn offindicating that the function
is deactivated.
4.1 To activate the intercom within an apartment, press button on the monitor while in standby.
The following call screen will be displayed, the status LED of button will blink rapidly and a long audible tone will
confirm that the call is being made or short tones will indicate that a monitor in the apartment is already communicating
with the door panel and the call will not be made. If a call is being made, press button to cancel the call.
Monitor in standby
4Intercom within an apartment:
Making an intercom call
01

Continued from previous page.
USER DIRECT ACCESS FUNCTIONS
VESTA7 G 2 MONITORB 14
If during the intercom process a call is received from the door panel of another apartment, the intercom process will be
cancelled; the monitor in the apartment will emit a melody to indicate that the call is being made and the image will
appear on the master monitor. To establish communication with the door panel, press button on the monitor. If
there are slave monitors in the apartment, press button on any of them.
If during the intercom process a call is received from another apartment, the intercom process will be cancelled; the
monitor in the apartment will emit a melody to indicate that the call is being made and the address of the apartment
making the intercom call will be displayed (see 'Intercom between apartments' on page 17-18).
The ringtones vary depending on where the call is being made from, enabling the user to identify its origin (door panel,
intercom or apartment door).
On the other monitors in the apartment, the status LED of button will blink rapidly and a melody will indicate that an
intercom call is being made. Press button to accept the call and establish communication, the status LED of
button will blink slowly, or press button to cancel it. If the call is accepted, communication will last for one and a half
minutes or until button is pressed again.
Receiving an intercom call
01
In communication
01

USER MENU
To access the menu, the monitor must be in standby. Then press menu button or to display the options screen of
the main menu.
15
Continued overleaf
Main menu screen
Description of the menu buttons:
VESTA7 G 2 MONITORB
Menu entry and user settings button. Display door panel image.
Intercom function between apartments.
Menu screen exit and selection button.
Menu entry and selection button.
Activate outdoor light.
C m ra/a e
Door panel Light Intercom About Settings
C m ra/a e
Door panel Light Intercom About Settings
Monitor in standby

To establish audio and video communication with the selected door panel, press button . The screen will
display symbol . Communication will last for one and a half minutes or until button is pressed again.
During door panel selection, door 1 and 2 can be opened by pressing the corresponding button / during the image
display or communication processes: one press will activate lock release 1 or 2 for five seconds.
The following screen will display the image from the door panel with address 1, indicating the selected door panel '01' and
the elapsed connection time. Then, using menu buttons and , select the required door panel/camera (DQ-CAM-GB2
module required) in descending and ascending mode respectively (carousel mode).
The connection will last for 30 seconds or until option is pressed twice if a door panel is selected or once if a camera is
selected.
During door panel selection, door 1 and 2 can be opened by pressing the corresponding button / : one press
will activate lock release 1 or 2 for five seconds.
USER MENU
16
1. Displaying door panel/camera images:
To display the image from one of the installed door panels/cameras, press button .
Continued overleaf
Continued from previous page.
VESTA7 G 2 MONITORB
Main menu screen
C m ra/a e
Door panel Light Intercom About Settings
00:01
01
00:01
01
Door panel selected
00:01
01
Camera selected
Start/stop communication.
To open door 1, press the door release button
during the call: one press will activate the lock
release for 5 seconds.
To open door 2, press the door release button
during the call: one press will activate the lock
release for 5 seconds.

USER MENU
17
Continued from previous page.
VESTA7 G 2 MONITORB
2. Activating the outdoor light:
To activate the outdoor light, press button . The outdoor light (SAR-GB2 module required) will activate for 1
minute. See the “TSAR-GB2 ML”user manual for how to set other light activation times.
Main menu screen
C m ra/a e
Door panel Light Intercom About Settings
To access the intercom function within an apartment, press button / . The following selection screen will be
displayed. Use buttons and to select the apartment to call.
IMPORTANT: Activate function codes and on the monitor (see 'Installer setup' on pages 19-20).[9015] [8017]
3. Intercom between apartments:
Main menu screen
C m ra/a e
Door panel Light Intercom About Settings
Apartment selection screen
[01]
[02]
[00]
[03]
Then press button / to make the call. The following call screen will be displayed indicating the address of the
apartment to call. The status LED of button will blink rapidly and a long audible tone will confirm that the call is
being made or a series of short audible tones will indicate that the unit called is in communication with the door panel or
on an intercom call with another apartment, and the call will not be made. If a call is being made, press option to
cancel the call.
Apartment selection screen
[01]
[02]
[00]
[03]
Making an intercom call
01
Continued overleaf

To exit the menu, press button .
USER MENU
18
Continued overleaf
Continued from previous page.
VESTA7 G 2 MONITORB
On the monitor(s) of the apartment called, the status LED of button will blink rapidly, a melody will indicate that an
intercom call is being made and the address of the apartment making the call will be shown. Press button to
accept the call and establish communication, the status LED of button will blink slowly, or press button to cancel
it. If the call is accepted, communication will last for one and a half minutes or until button is pressed again.
Receiving an intercom call
00
In communication
00
If during the intercom process a call is received from the door panel of another apartment, the intercom process will be
cancelled; the monitor in the apartment will emit a melody to indicate that the call is being made and the image will
appear on the master monitor. To establish communication with the door panel, press button on the monitor. If
there are slave monitors in the apartment, press button on any of them.
The ringtones vary depending on where the call is being made from, enabling the user to identify its origin (door panel,
intercom or apartment door).
4. Exiting the menu:
Main menu screen
C m ra/a e
Door panel Light Intercom About Settings
Monitor in standby

USER MENU
19
Continued from previous page.
Continued overleaf
VESTA7 G 2 MONITORB
5. About (information and installer setup):
Press button . The following selection and information screen will be displayed.
Main menu screen
C m ra/a e
Door panel Light Intercom About Settings
To access the installer setup, on the monitor's selection and information screen, press button for 3 seconds. The
following setup screen will be displayed.
Selection and information screen
00.00
00.01.00
AUTO
Installer setup screen
[ 0000 ]
Selection and information screen
00.00
00.01.00
AUTO
+
-
Use buttons and to enter the first function code number and then press button to enter the next function code
number; repeat the previous steps until the complete function code number is entered. Confirm the function code
entered by pressing button . To return to the previous screen, press option . (See installer function codes on
page 19).
Function codes (installer):
[8000]: Master monitor (default setting). [8001] to [8003]: Slave monitor 1 to 3.
[8016]: Menu not activated if BUS is busy (default setting). [8017]: Menu activated if BUS is busy.
[9015]: Intercom calls enabled. [9016]: Intercom disabled (default setting).
Each apartment must only have one master unit:Any other units in the apartment must be configured as slaves.
It is recommended to activate function code [8017]: If there is more than one monitor in the apartment and an intercom call needs to be made.
It is recommended to activate function codes [9015] and [8017]: To make an intercom call between apartments.
*
*
*
( )
1
( )
2
( )
Selection and information screen
00.00
00.01.00
AUTO
Installer setup screen
[ 8000 ]
+
-
( )
1
( )
1( )
2

USER MENU
20
Continued from previous page.
Continued overleaf
VESTA7 G 2 MONITORB
Press button to go to the main menu screen.
Main menu screen
C m ra/a e
Door panel Light Intercom About Settings
Selection and information screen
00.00
00.01.00
AUTO
6. Settings (ringtone, ringtone volume, default settings and language selection):
To access the monitor settings, press button . The settings screen will be displayed.
Main menu screen
C m ra/a e
Door panel Light Intercom About Settings
6.1 To change the door panel ringtone, use buttons and .
Then press option to change the intercom ringtone.
Settings screen
+
-
12
Intercom ringtone settings
+
-
03
+
-
12
Ringtone settings