golmar G2+ User manual

G2+ 2-wire installation
USER MANUAL
Kit Soul
Art 4 monitorLite
TECHNOLOGY
Cód. 50122625 TS5110 ART LITE EN4 REV.0120

SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE 2
CONTENTS
One apartment with one access panel and one monitor ..................................................................................23
Configuration switches.....................................................................................................................................9
Connection of a lock release...........................................................................................................................25
One apartment with two access panels and one monitor.................................................................................23
Setting the audio level ......................................................................................................................................7
Description ......................................................................................................................................................8
Installation .......................................................................................................................................................9
Installation .......................................................................................................................................................6
Contents ....................................................................................................................................................................2
Art 4 /G2+ monitor ...................................................................................................................................... to 2LITE 8 2
Main menu .....................................................................................................................................................10
Intercom menu...............................................................................................................................................22
Wiring diagrams............................................................................................................................................... to23 26
Description ......................................................................................................................................................4
Cross sections and distances.........................................................................................................................23
FA-G2+/ power supplyLITE ........................................................................................................................................4
Recommendations.....................................................................................................................................................3
Soul panel 4.3- /LITE .............................................................................................................................................5 to 7
Description ......................................................................................................................................................5
Installation terminals ........................................................................................................................................6
Configuration switches.....................................................................................................................................7
Installation terminals ........................................................................................................................................9
Settings menu........................................................................................................................................1 to 11 4
System operation .......................................................................................................................................................3
Door panel call screen....................................................................................................................................15
Image and communication settings........................................................................................................ to17 19
Installation .......................................................................................................................................................4
Timed 'do not disturb' menu....................................................................................................................20 to 21
Communication screen ..................................................................................................................................16
One apartment with up to two access panels and up to four monitors in cascade .............................................24
One apartment with up to two access panels and up to four monitors in distribution .........................................24
Connection of an external camera ..................................................................................................................26
Cleaning the door panel............................................................................................................................................29
Connection for an apartment door button........................................................................................................26
Compliance..............................................................................................................................................................30
Connection of an auxiliary device at the relay output .......................................................................................25
Cleaning the monitor ................................................................................................................................................29
Connection of an output button.......................................................................................................................26
Special codes ..................................................................................................................................................27 to 28

3
SYSTEM OPERATION
RECOMMENDATIONS
- The installation and handling of these devices must be carried out by authorised personnel.
- The wiring must run at least 40cm away from any other wiring.
- Preferably use a Golmar cable (2x1mm²).RAP-GTWIN/HF
- before making modifications to the device.Always disconnect the power supply
-Always follow the instructions contained in this manual.
- Check all connections before starting the device.
To make a call, the visitor needs to press the door panel button: an audible tone indicates that the call is being made
and LED on the door panel illuminates.At this moment, the apartment's monitor(s) receive(s) the call.
Detailed operation of the monitor is described on pp. 8 to 22.
Upon receiving the call, the image will appear on the screen of the master monitor (and slave 1, if it exists) without the
visitor knowing and icon displayed on the screen will blink green. To view the image from slave monitors 2 or 3,
press one of the buttons of the monitor to display the image. If the call is not answered within 45 seconds, door panel
LED will turn off and the system will become free.
To open door or activate auxiliary output of the door panel, press the button below the corresponding icon
displayed on the screen. A single press activates the lock release or auxiliary output for 3 seconds and LED on
the door panel illuminates.
,
In systems with two access doors, the other door panel automatically disconnects; if another visitor attempts to call, a
number of telephone tones will indicate that the system is busy and LED on the door panel will illuminate.
To establish communication, press the button below the off-the-hook icon shown on the screen. Door panel
wLED ill illuminate. Communication will last for 90 seconds or until the button below on-the-hook icon shown
on the screen is pressed. When communication has ended, door panel LED will turn off and the system will
become free.
12
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE

4
FA-G2+/ POWER SUPPLYLITE
Description
Installation
Install the power supply in a dry, protected and ventilated location. Make sure that the vents are not obstructed.
Use a DIN 46277 rail for fastening ( elements).4
Note that current regulations stipulate that the power supply must be protected by a circuit breaker.
Connect the wires to the installation terminals following the instructions in the diagrams.
The fitting and handling of the power supply must be carried out by authorised personnel in the absence of
electrical current.
To prevent electric shock, do not remove the protective cover without first disconnecting the power supply. Replace
it once all connections have been made.
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
C
D. Current input connection terminals.
E. Detail of the current input terminals without
protective cover.
A. Monitor Bus connection terminals.
B. Door panel Bus connection terminals.
C. Protective cover for the current input.
NL
12240141 V01
OUTPUT
M
GOLMAR S.A.
C/ Silici, 13
08940 - SPAIN
MADE IN CHINA
BUS 30V 2V 0.5A±
INPUT ~100-240V
0.8A 50-60Hz
FA-G2+/LITE
PL
BUS BUS
N L
BUS(M) BUS(PL)
DIN rail.
Fastening tab on the DIN rail.
DIN rail.
B
D
E
A

5
SOUL PANEL 4.3- /LITE
Description
A
B
C
F
E
D
J
I
G
J
G
H H
B
C
D
L
M M
K M
Q
O
O
P
I
N
T
K
R
S
T. .No function
Lock release activated.
H. Colour camera.
B. System status indicator lights.
A. System status icons:
F. .Nameplate label
M. Wall fixing hole (x3). Do not overtighten the
fixing screws.
System busy.
G. Speaker grill.
O. Installation terminals.
P. Cable grommet.
Communication established.
R. Configuration switches.
L. .Illumination module
Q. connector.Illumination module
K. Front fixing screw.
C. Ambient lighting sensor.
N. gasket.Illumination module
S. Volume control potentiometer.
Call in progress.
J. Microphone hole.
D. Night viewing lighting.
E. Protective polycarbonate.
I. Call button(s).
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE

6
Installation
4. Drill three 6mm holes at the indicated points (M), see p. 5. Insert the plugs supplied and fix the door panel to the
wall using the screws supplied.
3. Present the door panel to the wall, positioning the top at 1.65m. Pass the installation cables through the cable
grommet.
5. Connect the cables to the removable terminals following the instructions in the installation diagrams.
Before replacing the and closing the door panel, perform the necessary settings (illumination module address door
panel illumination module, audio level setting, etc.), as indicated throughout this manual. Make sure that the
gasket is properly fitted.
2. Remove the screws that secure the proximity reader.
1. Remove the metal front piece of the door panel by loosening the bottom screw with the Allen key supplied. On
the back of the front piece, you will find the button personalisation label.
For correct installation: (locate the top of the door panel at a height of 1.65m).
The door panel has been designed to withstand diverse environmental conditions. It is however advisable to take
extra precautions to prolong its service life, such as locating it in a covered area.
For optimum image quality, avoid direct contact from light sources (sunshine, street lights, etc.).
Installation terminals (O)
For ease of installation, the installation terminals are removable and supplied in a separate bag. Once the
terminals are wired, place them in position.
BUS BUS CV- CV+ AP+
C NA GND CCTV AP-
ON
1 2 3 4
IMPORTANT: Installation with 2 access door panels and
AP button on both door panels, one of the door panels
must connect the AC lock release (instead of DC lock
release). SAR-12/24 required,
see pages 25 to 26.
relay a TF-104 transformer&
AP AP+, -: remote activation button connection. Note: For correct
operation, the monitor's address 1 must be connected to
the Bus.
GND CCTV, : input for external analogue camera.
CV CV-, +: lock release output 12Vdc (maximum 270mA).
BUS BUS, : communications bus (non-polarised).
C, : potential-free relay output (maximum 6A/24V).NA
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
SOUL PANEL 4.3- /LITE

7
Configuration switches (R)
All switches are factory set to OFF.
Configuration changes should be made with the equipment turned off. If they are performed with the equipment
turned on, disconnect it for 10 seconds after any modification.
Switch 1.
Defines the door panel address.
Switch 2, must be OFF.
OFF-OFF
OFF OFF-
O -OFFN
Door panel 1 Door panel 2
Apartment 1
Switches and must be OFF.3 4
Setting the audio level
If the audio volume on the door panel after starting up the device is not adequate, use the volume control
potentiometer (S). This setting affects the communication and confirmation tone audio level.
BUS BUS CV- CV+ AP+
C NA GND CCTV AP-
ON
1 2 3 4
ON
12 3 4
ON
12 3 4
ON
1 2 3 4
S
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
SOUL PANEL 4.3- /LITE

8
ART 4 /G2+ MONITORLITE
Description
*
The function of each button is shown on the monitor
screen with an icon located just above each button
(see pp. 10 to 22).
C. LEDMonitor status :
B. Function buttons, access and selection of menu
functions.
- With the special code '0441' (Doctor mode) already
entered (see pp. 27 to 28), press the button for 1 sec.
to activate/ deactivate the function.
Red ON: “Do not disturb” Mode a tivated.c
Press to access 'Doctor mode' function (standby monitor):
A. Speaker.
Yellow ON: Standby without notification.
- The push button led will blink in white color if the
function 'Doctor mode' is activated and it will turn off if
the function is deactivated. J. Installation terminals.
D. 4.3" TFT colour screen.
Above this raised dot is the 'Start/ nd communication'
button.
E
Above these raised dots is the 'Door opening' button.
In call :/communication
F. Microphone.
G. Raised dots for the visually impaired people.
H. Wall mounting connector fixing (x4).
I. Configuration switches.
E. Golmar use.
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
A
D
B
CFE
G
H
I
J
H
H
H
SA
GND
HZ
HZ
ON
1 2 3 4 5 6 7 8
BUS
BUS
12210435 V02Product Version:
MONITOR 4.3” ART 4 LITE/G2+
GOLMAR S.A. C/ Silici, 13 08940-SPAIN
WARNING To prevent fire or electric shock, do not expose this device to rain or moisture
To prevent electric shock, do not remove cover.
CAUTION
No user serviceable parts inside. Refer servicing to qualified service personnel
MADE IN CHINA
128
codes
SA
OF F = 0
ON = 1
DIP 1 to 7
DIP 8
Moni tor
address
EOL
resis tor
GND
HZ
HZ
BUS
BUS
128
codes

9
Installation
Avoid dusty or smoky environments or locations near sources of heat.
For proper installation, use the template supplied with the product.
1. Position the top of the template at a height of 1.65m.
2. If you are going to use an embedding box to pass the wiring through, make sure that it is in line with the holes
corresponding to the box model chosen and fix the connector. If you prefer to fix the connector directly to the
wall, make four 6mm holes at the points indicated (A), insert the wall plugs supplied and screw in the connector.
3. Pass the installation wires through the middle hole and connect them to the removable terminals as shown in the
wiring diagrams. Before connecting the removable terminals to the monitor, configure the switch as indicated
below.
4. Connect the removable terminals to the monitor and place the monitor in front of the connector, making sure the
fixings line up. Move the monitor downwards to secure it.
Installation terminals (J)
For ease of installation, the installation terminals are removable and supplied in a separate bag. Once the
terminals are wired, place them in position.
SA GND, : Auxiliary call repeater output (max 50mA/12V), relay SAR-
12/24.
HZ HZ, : Apartment front door button input:
Connect only on the master monitor. The signal received is then
transmitted to the slave monitors in the same apartment through the BUS.
BUS, BUS: Communication BUS (non-polarised).
Configuration switches (I)
Switches 1 to 7.
These assign the address of the corresponding monitor to its call button on the door panel. Switches to must
remain in the OFF position.
2 7
Note: ART4 LITE/G2+ monitor with V.02 and next.
Apartment 1
Not : ART4 LITE/G2+ V.02e monitor with and next, (ver p. 27 a 28 ).to define the monitor as master or slave
Switches 6 and 7. Only ART4 LITE/G2+ monitor with V.01.IMPORTANT:
These define whether the monitor is master or slave. Each apartment must have one master monitor, and only one.
Switch 8.
This activates the end-of-line resistance in the ON position. Activate it in monitors where the bus cable ends.
Deactivate it only in intermediate monitors.
Not : LITE/ 1 .e ART4 G2+ monitor with V.0 and next
Slave 1 Slave 2 Slave 3Master
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
SA
GND
HZ
HZ
ON
1 2 3 4 5 6 7 8
BUS
BUS
ON
1 2 3 4 5 6 7 8
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Note: HZ push button function mode: When HZ push button is pressed will be call tone and activate the output of
auxiliary call repeater with standby monitor call process m ation process HZ tone with lower audio level
process and "Do not disturb" mode
, , com unic ( ),
intercom .
Switches 1 to 5. ART4 G2+ monitor with V.0IMPORTANT: LITE/ 1:
Switches 2 to 5 must remain in the OFF position.

10
Main menu
If the device is in standby (screen switched off), to access the main menu, press any of the buttons of the monitor.
Then press the button located just below the corresponding icon. The device will return to standby mode after
seconds without activity.
20
Press the button below icon to display the image from the door panel. Note: This enables
the door panel camera to be changed, the audio on the corresponding door panel to be activated
and the door to be opened (see p. ).
master
15
Press the button below icon to access the menu of the intercom between other monitors in the
same apartment (see p. 2 ).2
Press the button below icon to make changes to the system settings (see pp. 1 -1 ).1 4
To 20 to 21set a period of time for 'Do not disturb' mode (see p. ).
Press the button below icon to enable disable the 'Do
not disturb' function: If the monitor is in 'Do not disturb' mode, the status LED will
illuminate (red) and the ringtone on the monitor will not sound when a call
for 3 seconds and for 1 second to
(“HZ”
p g )
see note
a e 9 is received.
Main menu
Disabled Enabled
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE

11
Settings menu
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Settings menu
Returning to the main menu: Press the button
below icon to return to the main menu.
The 'About' screen provides information about the monitor, such as the software version, address and
whether it is master or slave (M, S1, S2 or S3).
It enables the monitor to be restored to factory settings, such as melodies, call volume, etc.
Press the button below icon to return to the settings menu.
It enables updated versions of the manual to be downloaded to a mobile or tablet, for which it is
necessary to have a QR code scanner app installed.
Settings menu ‘About' screen
To restore the monitor to factory settings, press the button below icon to access the factory reset
menu, then press the button below icon to perform this function. Press the button below icon to
return to the 'About' screen.
Press the button below icon to return to the settings menu.
No function.
See pages 12 to 14.
Settings " " mode:automatic door opening
FW
0 /01 M
1.02
Continued overleaf

12
Settings menu
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Continued overleaf
Continued from previous page.
Selecting the melody and call volume: Press the button below icon to access the settings screen.
In order to identify the origin of the calls when you are not in front of the monitor, select different
melodies and the desired call volume. Go to the option to be modified by pressing the buttons
below corresponding icons / , then press the buttons below corresponding icons / to
select the melodies and desired call volume. Press the button below icon to return to the
settings menu. Important: KIT S5110 ART4 LITE.Door panels & have no use with
Option selection screen
105
205 03
01
02
305
405
03
Settings menu
Settings menu
Settings " " mode:automatic door opening with the special
code '0441' (Doctor mode) already entered for automatic door opening
This selection is visible in the settings menu,
in the monitor (see special
codes pp. 27 to 28). Then press the button below icon to access the settings menu.
1
Option selection screen
3
4
07h
24h

13
Settings menu
Continued overleaf
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
If you wish disable the automatic door opening , go to the option with icon by pressing the
button below icon , deselect the option by pressing the button below icon .
.
Press the button
below icon to return to the settings menu (This function is disabled by default. To enable
it, see pp. ).27 to 28
To enable the
.
.
automatic door opening (after 3 seconds of receiving a call from the door panel),
go to the option with icon by pressing the button below corresponding icon and select the
option by pressing the button below icon Press the button below icon to return to the
settings menu
To set a period of time for automatic door opening (after 3 seconds of receiving a call from the
door panel), go to the option with icon by pressing the buttons below corresponding
icon and select the option by pressing the button below icon . Then you can set a period of
time for opening the door , by pressing corresponding buttons
/ , and validate the changes made by pressing the button below icon . Press the button
below icon to return to the settings menu.
(from 1h to 24h) ' ' function mode
(This function is disabled by default. To enable
it, see pp. ).27 to 28
1
1
1
Time period setting screen
07h
Option selection screen
01h
Continued from previous page.
24h24h
24h
24h
24h

14
Settings menu
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Continued from previous page.
Press the button below icon to return to the . automatic door openingmain menu If the ' ' mode is
enable (see pages 12 to 13) the icon will be displayedin the top left of the screen in the main
menu and the button led will blink white color with the monitor in standby .(screen switched off)
Settings menu Main menu

15
Door panel call screen
This screen is displayed when receiving a call or pressing the button below icon of the main menu. During a
call, icon displayed on the screen will blink green (during the call process). In the top of the screen, the
source of the image is displayed (door panel 1, door panel 2, camera 1 or camera 2). The call has a duration of
45 seconds.
right
Press the button below icon / to start or end audio communication with the door
panel displayed respectively. Communication has a maximum duration of 90 seconds.
Once communication has ended, the screen will turn off.
Press the button below icon to change the source of the image as long as the system has more
than one door panel or has an external camera connected and display has been activated
27 28(see pp. - ). It is possible to make the change during display, call and communication
processes.
Press the button below icon to activate the lock release (or device connected to the CV output of
the door panel) for 3 seconds (factory setting, programmable by the installer; see pp. - ).27 28
Press the button below icon to activate the lock release (or device connected to the relay output
of the door panel) for 3 seconds (factory setting, programmable by the installer; see pp. - ).27 28
1
2
1
2
Press the button below icon to access the image and monitor in call volume settings
menu. Select the option to be modified by pressing the buttons below corresponding icons / ,
change to the desired level by pressing the buttons below corresponding icons / and validate
the changes made by pressing the button below icon , (see pp. - ).
by 3 seconds
17 19
2
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
1
12
Press the hidden button below icon to cancel the current call or display and return to the main
menu.

16
Communication screen
This screen is displayed during a communication process. In the top of the screen, the source of the image is
displayed (door panel 1, door panel 2, camera 1 or camera 2).
right
Press the button below icon / to start or end audio communication with the door
panel displayed respectively. Communication has a maximum duration of 90 seconds.
Once communication has ended, the screen will turn off.
Press the button below icon to change the source of the image as long as the system has more
than one door panel or has an external camera connected and display has been activated (see pp.
27 28- ). This enables the door panel camera to be changed, the audio of the corresponding door
panel to be activated and the door to be opened.
Press the button below icon to activate the lock release (or device connected to the CV output of
the door panel) for 3 seconds (factory setting, programmable by the installer; see pp. - ).27 28
Press the button below icon to activate the lock release (or device connected to the relay output of the
door panel) for 3 seconds (factory setting, programmable by the installer; see pp. - ).27 28
1
2
1
2
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
1
12
No function.
Press the button below icon for 3 seconds to access the image and monitor in communication
volume settings menu. Select the option to be modified by pressing the buttons below
corresponding icons / , change to the desired level by pressing the buttons below
corresponding icons / and validate the changes made by pressing the button below icon ,
(see pp. 1 1 ).7 to 9
2

17
Image and communication settings
Continued overleaf
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
During communication process , press the button below icon for 3
seconds to access the image and monitor in communication volume settings menu.
a call process or during a(Screen A) (Screen B)
call/
2
The following brightness control menu will then be displayed. Adjust to the desired level by pressing the buttons
below icons / . To access the contrast control, press the button below icon . To exit the image and
communication settings menu, press the button below icon .
1
4
Press for
3 seconds
1
12
1
12
Call process screen Communication process screen
Press for
3 seconds
Screen A Screen B

18
Image and communication settings
Continued overleaf
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Continued from previous page.
The following contrast control menu will then be displayed. Adjust to the desired level by pressing the buttons
below icons / . To access the colour control, press the button below icon . To exit the image and
communication settings menu, press the button below icon .
The following colour control menu will then be displayed. Adjust to the desired level by pressing the buttons below
icons / . To access the monitor communication volume control, press the button below icon .
To exit the image and communication settings menu, press the button below icon .
call tone /
1
4
1
4

19
Image and communication settings
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Continued from previous page.
The following call tone settings volume during a call process or communication settings volume during
a communication process
(Screen A)
will then be displayed.Adjust to the desired level by pressing the buttons
below icons / . To return to the brightness control (carousel mode), press the button below icon .
(Screen B)
Communication screen
To exit the image and communication settings menu, press the button below icon .call /
Call tone settings volume Communication settings volume
Screen A Screen B
1
2
1
2
1
2
1
12
Communication settings volume
Screen B

20
Period of time for 'do not disturb' mode menú
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
'Do not disturb' mode settings:
below icon to access the
settings screen.
If the device is in standby (screen switched off), to access the main
menu, press any of the buttons of the monitor. Then press the button
Option selection screen
Main menu
To enable the 'Do not disturb' mode (see
note "HZ" page 9),
.
main .
in which the monitor will not sound when receiving calls
go to the option with icon by pressing the button below icon and select
the option by pressing the button below icon Press the button below icon to return to the
menu
If you wish disable the 'Do not disturb' mode, go to the option with icon by pressing the button
below icon , deselect the option by pressing the button below icon .
.
Press the button below
icon to return to the menumain
To set a period of time for in which the monitor will not sound when receiving
calls and
select the option by pressing the button below icon Then you can set a period of time
"Do not disturb" mode
(see note "HZ" page 9), go to the option with icon pressing the button below icon
. (from 1h
to 24h) 'Do not disturb' modefor , by pressing corresponding buttons / , and validate the
changes made by pressing the button below icon . Press the button below icon to return to
main menu.
Continued overleaf
07 h
24h
24h
24h
24h