GPM STRATFORD ROBSTR1 BK User manual

GOLBAL PROCUREMENT AND MARKETING LIMITED
Assembly instruction- Please keep for future reference ROBSTR1 BK
Dimensions No.People Assembly Time OW#
Width: 40 cm
Depth: 48 cm
Height: 180 cm
60 mins
(approx)
thank you
For purchasing this
GPM Limited
product
1
ROBSTR1 OK
ROBSTR1 BK
STRATFORD SINGLE DOOR ROBE
ROBSTR1 WH ROBSTR1 GY
ROBSTR1 OK
ROBSTR1 WH
ROBSTR1 GY
400mm
1800mm
480mm
76mm
If you need help or have damaged or missing parts, please email [e-mail]
Important
PLEASE READ THESE INSTRUCTION FULLY BEFORE STARTING ASSEMBLY.
PLEASE DO NOT THROW THE PACKAGING AWAY UNTIL YOU ARE STATISFIED WITH PURCHASE,
GOODS NEED TO BE RETURNED IN ORIGINAL PACKAGING.

Safety and Care Advice
!
Important-Please read these instructions fully before starting assembly
If you are unhappy with the product and wish to return it,
please following the retailer’s returns procedure.
Components - Panels
Make sure you have enough
space to lay out the parts
before starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close to
its final position (in the same
room) as possible.
Assemble on a soft, level
surface to avoid damaging the
unit or your floor.
We do not recommend the
use of power
drill/drivers for
inserting screw,
as this could
damage the unit.
only use hand screwdrivers.
Dispose of all packaging
carefully and responsibly.
Care and Maintenance
This product should not be
discarded with household
waste.Take to your local
authority waste disposal centre.
From time to time check
that there are no loose
screws on this unit.
Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
2
Check you have all the
components and tools listed
on pages 2,3 and 4.
Remove all fittings from the
plastic bags and separate
them into their groups.
Keep children and animals
away from the work area,
small parts could choke if
swallowed.
1
2
3
4
5
6
7
8

Components - Panels
Please check that you have all the components listed below before constructing your item.
Important-Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please email [e-mail]
If you have damaged or missing components,
email: [e-mail]
Part No Description Qty Thickness
(mm)
1
2
3
4
5
6
7
Right Side Panel
Bottom Panel
Top Panel
15 mm
15 mm
15 mm
15 mm
15 mm
15 mm
3 mm
1
1
1
1
1
1
1
1
3
Left Side panel
15 mm
Lower Front Panel
Back Panel
Door Panel
8
Horizontal Panel

Components - Fixings
Please check that you have all the components listed below before constructing your item.
Important-Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please email [e-mail]
If you have damaged or missing components,
email: [e-mail]
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
0
mm
10
515 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170 175 180
Ruler - Use this to measure your screws (mm)
Tools Required ( Not Provided)
(A) (B) (D)( C )
4
M3.5 X 20mm
X 2
Wall Plug
X 2
Strap
X 1
Bracket
X 2
M4 X 32mm
X 2
HARDWARE
ANTI - TIPPING KITS
Allen Key
X 1
Handle
X 1
Leg Pin
X 4
JCBC M6 X 40mm
X 14
M3.5 X 14mm
X 18
Button Head 18mm
X 2
Nail
X 27
Hinges
X 3 set
Hanger Rod
X 1
(E)
(F) (G) (I)( H)
(J) (K) (M) (N)(L)

Assembly Instructions If you have damaged or missing components,
email: [e-mail]
Step 2Step 1
Step 3
5
Step 4
2
Attach panel , , , and Hanger rod ,
3 4 5 H
to Left & Right panel & , as shown and secure
1 6
with JCBC Screw , tighten with Allen Key .
A I
A
A
A
A
A
A
A
A
A
A
A
3
H
6
1
4
5
2
C
D
7
D
D
D
2b. M
Attach the Anti-Tipping kit bracket
M
at the back of the wardrobe, with
K
Screw , using a Philip head Screw
driver.
2a.
to the back of the wardrobe
Attach Back board ,
7
with Nail , using a small hammer.
C
2c.
the wardrobe using a small hammer.
Attach Leg Pin , to the base of
D
K
8
B
G
F
E
3a. Attach Hinges to Door , with
using a Philip head Screw driver.
G8
Screw on the marked pilot holes,
B
Philip head Screw driver.
3b. Attach door handle E
with Screw using a
F
1st
WALL
Drill
Bit
6mm
2nd
4th
L
M
M
M
J
N
complete
Attach the Anti- Tipping kit onto
wall Following the steps as shown.