Graco Hydra-Clean 2104ES Operation manual

This manual contains IMPORTANT
WWARNINOS
and INSTRUCTIONS
READ
AND RETAINFORREFERENCE
MODEL 800-048 SERIES "A"
2 150 psi (150 bar) OPERATING PRESSURE
2250psi (155 bar) MAXIMUM WORKINGPRESSURE

~NJECTOQIM HAZARD
penetratetheskinandcauseextremelyserious
Fluids under high pressure from spray or leaks can
injury, including the need for amputation.
NEVER point thespray gun at anyone or any part of
the body.
NEVER put hand or fingers over the spray tip.
NEVER try to stop or deflect leaks with your hand or
body.
ALWAYS have the tip guard in place when spraying.
MEDlCAU TREATMENT
If anyfluidappearstopenetrateyourskin. get
EMERGENCY MEDKAL CARE AB ONCE.
DO MOK TREAT AS A SIMPLE GUT.
Tellthedoctorexactlywhatfluidwasinjected. For
treatmentinstructions haveyourdoctorcallthe
RIAJIORIAU POISON CENTER NETWORK
($a2w~-666~
AVOID COMPONENT RUPTURE
Even after you shut off the gasoline engine, there is
high pressure in the pump,hoseand gun until you
release
it by triggering the gun. So before removing
the spray tip or servicing the unit,
always shut off the
unit
and trigger the gun to release pressure.
Be surethatallaccessoryitemsandsystem
NEVER exceedthe pressure rating of any component
components
will withstand the pressure developed.
personalsafety,aswell as thefunctionofthe
in system. NEVER alter or modify equipment -your
equipment, is at stake.
damaged conditions caused by traffic, sharp corners,
Beforeeach use,checkhoseforweak, worn or
pinchingorkinking.Tightenallfluidconnections
securelybeforeeachuse. Replace anydamaged
hose.
Do notusechemicalsoragentswhicharenot
compatible with Buna-N and
PVC or neoprene cover
of hose.
Do not leave a pressurized unit unattended. Shut off
the unit and release pressure before leaving.
FORE
Do not spray flammable liquids. Do not operate the
enginewherecombustiblefumesordustmay be
present.
GENERAL
NEVER runtheunitwiththebeltguardremoved.
Keep clear of moving parts when the unit is running.
Observedetergentmanufacturer'ssafety
precautions. Avoid getting detergent or other liquids
in your eyes. Follow the directions on the container
breathingfumes,etc.Alwayswearfullgogglesto
regardingcontactwith eyes, nose, andskin,
dislodged by the spray. If necessary, wear gloves or
protect your eyes from thespray
as well as any debris
otherprotectiveclothing.Ifantidotesortreatment
are 'recommended, be prepared to use them.
DON'T spray toxic chemicals such as insecticide or
weed killer.
This unit is supplied with an 8-foot power cord made
electriccordisconnectedtotheunitchassisand
up
of three AWGNo. 10 wires. The green wireof the
motor frame. The other three wires are connected to
the starter switch.
Be sure to connect the power cord
to the appropriate
approved plug to
fit your requirements.
The starter switch has a built-in circuit breaker that
circuit
is overloaded.
willshut off thepowertotheunitwheneverthe
Always check tobe sure the switch
is off andthat the
before plugging in the power cord.
hosesandelectriccordareclear
of movingparts
IMPORTANT
:
..
United States Government safety standards have been adopted under the Occupational Safety and Health Act.
These standards
- particularly the General Standards,Part 1910. and the ConstructionStandards,Part 1926 -
Should be consulted in connection with your use of airlessspray equipment.
~ ..
2 801-457
... . .. . . . . ._i.. . . . ~. . .... . .. . .- .~. . ..

INSTALLATION
Check Electrical Service and Plug In
service is 1 phase 220 V, 60 HAC, 30 Amp. WitKthe
Before plugging
in the sprayer, be sure the electrical
ON-OFF switch
in the OFF position, plug the power
extensioncord,
it must have 3 wires of at least 10
supplycordinto
a groundedoutlet.Ifyouusean
gauge (2.5
mm2) and should not be over 100 ft (30.3
m) long.
Install Wheels and Handle
Slide the axle through the frame. Slide the wheels
and washers onto the axle and secure
in place with
cotter pins provided. Install the hubcaps. Attach the
handle
with thefour screws, flatwashers, lock
washers and nuts provided.
l,nstall
Hose and Spray Gun
Connect the spray hose to thespray gun by inserting
thepinattheend of the hose intothequick
disconnect coupler on the gun. Connect the hose to
the fluid outlet
in the same way.
Remove the tape from thecap on top of the pump.
- .. .
$. CleaningAccessories
'.. i For sprayingdetergent or othercleaningsolution,we
' Accessories andinstructionmanual801-192for
recommend using
a chemicalinjectorkit. See
installation and operation.
For removing rust andold paint we recommend using
awater sandblaster.
See Accessoriesand instruction
manual 801.190 for installation and operation.
Connect
To Water Supply
CAUTION
plumbing code regardingcross-connectionto
Beforeattachingtowater supply.checklocal
water supply. Backflow check valve 801-133.
pump
in a direct supply system.
Do notexceed 1 6OoF(7OOC) water temperatureto
fromyourcitywatersupplytotheunit's
3/4 in.
Connectahose with atleasta 3/4 in. (19 mm) ID
garden hose threaded inlet. The supply hose should
not be more than
50 ft. (15 m) long.
NOTE: For adirectsupply system,your water
AT LEAST 5 GPM (19 LITER/MINI.
source at the unit must have aflow rate of
If your operating conditions are different fromabove.
assistance.
contactourCustomerServiceDepartmentfor

OPERATION
Startup 1..
and setup instructions.
Before starting, be sure to read the safety warnings
Turn on the water supply.
Trigger the gun to release anyback pressure.
CAUTION
Never run the cleaning unit dry. Costlydamage
to the pump will result. Always be sure water
supplyiscompletelyturnedonbeforeoperating.
Inspect allconnectionsforany leaks. Tightenif
necessary.
Cleaning
For cleaningtechnique, see theChemicallniector
manual,
801 -1 92.
For abrasivecleaning, see theWaterSandblaster
manual,
801 -1 90.
Follow these precautions when removing and
installing nozzles:
1. Shut off the cleaning unit and trigger thegun
to relieve pressure.Engagethe trigger safety.
2. Keep the nozzle a.nd the tube pointed away
from you and everyone else.
3. Do not put your handover the tip to push the
keep your fingers away from the tip.
nozzle into place. Grasp
it from theside and
4. Do not let anyone else touch the spray'valve
while you are cleaning nozzles.
5. Be sure the slip ring is pushedforward tolock
the nozzle in place beforetriggering thespray
gun.
.
Shutdown and Care Of Unit
When unit is not in use, turn off water supply.
When shutting down for theday or weekend,
shut off
unit, shut off water supply valve, and trigger gun to
release pressure. Wipe off the unit with
a damp rag.
CAUTION
overheatifleftrunningforover 10 minutes
spraying.forlongerpumplife.Thepump
will
as often as necessary, at least daily. Do not operate
Check the filter screen
in the water inlet connection
the unit with the inlet and filter screen removed.
DONOTtrytoadjusttheunloadervalveorchangethe
engine speed.Changingthesesettingsmaycause
excessive pressure, intermittent unloader operation,
wastedfuelandincreasedwearonpartsandwillvoid
the warranty.
PUMP MUSTNOT BE RUN
DRY and must bedrained
of water prior to exposure to freezing temperatures.
Use and store the unit where it
will not be subjected
to freezing temperatures.
If water does freeze in the
solutionmaybepumpedpriortocoldweather
unit, thaw before trying to start. A
50% anti-freeze
storage.
Use only spray tips that are matched to the unit to
avoidexcessivecyclingandwearoftheunloader
valve. See Accessories.
temperaturechangemaycracktheceramic
pourhotwateronafrozenpump.A sudden
plungers.
Do not pump caustic materials.
Before extended storage, flush the pump with light
oil.
Avoiddragginghoseoveranabrasivesurfacesuchas
cement.Thiscausesexcessivewearandshorter
hose life.
Clean the intake line strainer daily
Lubrication and Care
Fill pump crankcase to dot on oil gauge window with
25 02. (0.75 liters) of crankcase oil (part no. 801 -1 44)'
or equivalentSAE 40 weighthydraulicoil with
antiwear and rust inhibitor additives. Change initial
fill after
50 hour running period.Change oil every 3
months or at 500 hour intervals.
WARMING
I NEVER alteradiustment or modifvtheunloader 1
I
valve.
I
Altering or adjusting unloader willnot increase
performance of unit.
4 801-457
.. . . ... , . .. . . . . ._ . . . . . . . ... . .. .. ~ . .
.. . . .. .. . .. I. . .

PROBLEM
Low pressure.
Pump runs extremely rough,
uressure low.
Waterleakage from under
the manifold.
Water in pumpcrankcase.
Frequent or premature
failure of the packing.
Strong surging at the inlet
3nd low pressure on the
jischarge side.
CAUSE
Worn nozzle.
Belt slippage.
Air leak
in inlet plumbing.
Relief valve stuck, partially
valve seat worn.
plugged or improperly adjusted
Inlet suction strainer clogged
o
improper size.
Worn packing. Abrasives in
pumped fluid or severe cavita-
tion. Inadequate water supply.
Fouled or dim/ inlet or discharge
valves.
Worn inlet or discharge valves.
Leaky discharge hose.
Restricted inlet or air entering
the inlet plumbing.
Inlet restrictions and/or air
valve.
leaks. Stuck inlet or discharge
Leaking
H.P. seals.
Worn packing.
condensing into water inside the
May be caused by humid air
crankcase.
Scored plungers.
Over pressure to inlet manifold
Damaged or worn plungers.
Abrasive material
in the fluid
beingpumped.
Excessive pressure and/or tern
perature of fluid being pumped.
Over pressure of pumps.
Running pump dry.
Foreign particles
in the inlet or
discharge valve, or worn inlet
and/or discharge valves.
SOLUTION
Replace with nozzle of proper size.
Tighten or replace; use correct belts and replac
both at same time.
Disassemble, reseal, andreassemble.
Clean. and adjust relief valve; check for worn
and dirty valve seats. Kit available.
Clean.
Use adequate size.Check more
frequently.
Install proper filter. Check flow available to
pump.
Clean inlet and discharge valve assemblies.
Replace worn valves, valve seats and/or
discharge hose.
Proper size inlet plumbing; check for airtight
seal.
Clean out foreign material, replace wornvalve:
Replace seals.
Install new packing.
Change oil at
3 month or 500 hour interval
using Graco Crankcase
Oil (other approved o
every month or 200 hours) P.N. 801-144.
?eplace plungers.
?educe inlet pressure.
3eplace plungers.
nstall proper filtration on pump inlet plumbing
:heck pressures and fluid inlettemperature; bc
jure they are within specified range.
?educe pressure.
10 not run pump without water.
:heck for smooth lap surfaces on inlet and
iischarge valve seats. Discharge valve seats
md inlet valve seats may be lapped on
a very
ine oil stone.

building circuit fuse blown.
Overload switch has opened.
Electric motor stops while Power cord unplugged, or
spraying. building circuit fuse blown.
Overload breaker.has opened.
Extension cord
Tip plugged.
Electric motor runs,
but
Displacement pump frozen or
no output. gear train damage.
SOLUTION
Check, replace.
Unplug power cord'. decrease pressure
Check, replace.
~ ~~~
Unplug poweicord'. relieve pressure-allow
to cool.
DonZ usemorethan
loOftoi 8 ga extension cord.
Remove and clean
Thaw,
'This
unit has an overload breaker built into the switch assembly. If it opens, unplug power cord and let sprayer
cool for
30 to 60 minutes. Also, try to correct the causeof overheating. Always use the lowest pressure setting
needed.
NOTE: A M11 and M30 metricwrenchesare
required for servicing pump.
PUMP
Photo 1 and 2.
Valves
1) Remove the hex plug using an M30 wrench.
2) ExamineO-ringunderplugandreplace if
evidence of cuts or distortion.
3) Removevalveassemblyincluding,retainer.
spring, valve and valve seat from valve cavity.
MOTE: Valve assembly may come apart during
removal.
41 Replacevalve parts with service kit (801-041)
includingretainer,spring, valve,valveseat, o-
ring and back-up-ring.
5) Replace valve cover and torque to 75 ft-lb (100
Nm).
Photo 3.
Pumping Section
2) Separate the manifold from the crankcase.
1) Remove the four {4) hex nuts from the manifold.
NOTE: It maybenecessarytotap manifold
lightly with mallet to loosen.
I 1
Keep manifold properlyaligned with ceramic
plungers when removing toavoid damage to
either Dlunclers or seals.
~ ~~
3) Carefully examine each plunger for any scoring
~~ ~
and replace if necessary.
6 801-457
..
.... ~ ...... ... ~ ..
..

Plungers
Photo 4.
1)Using.an M1 1 wrench,
remove the plunger retainer.
2) Slide out theseal retainerwith
oilwickandrubberbarrier
3). With a slight twisting motion,
slinger.
loosen theplungerfromthe
plunger rod and remove.
MOTE: The studmayremain
withtheretainer
whenremoved.
Disassembleand
screwstudinto
plungerrodfinger
tight.
4) ReplaceO-ring and back up
5) Saturatenewoilwick by
6) Install new plunger.
7) Replace plungerretainerand
torque to
80 in-lb (9 Nm).
8) Installnewoilwickinseal
retainer.
9) Replace barrierslingerover
10) Lubricate each plunger sleeve
new plunger.
andcarefullyslidemanifold
onto crankcase.
ring on plunger retainer.
soaking
in oil.
Photo 5, 6, 7 and 8.
Seals or V-Packings
2) Then remove the low pressure
1)Remove C-ring fromsealcase.
3) Unscrewtheseal case from
seal from the seal case.
themanifoldusingaspecial
key wrench (801
-044).
4) Remove thehighpressure
seal andexamine.Before'
of new high-pressure seal and
replacing, lubricate
ID and OD
press into manifold.
NOTE: A socket andexten-
sionmaybeusedto
pressuresealfrom
manifold.
5) Install newO-ring on seal case
6) Screw seal case into manifold.
and lubricate OD of O-ring.
7) Lubricate ID and OD of low
pressuresealandpressinto
8) Replace C-ringholding low
seal case.
pressureseal in place.
9) Lubricate each plunger sleeve
onto crankcase.
andcarefullyslidemanifold
NOTE: Whenreplacing
enreme caution should
manifold onto plungers,
be exercised to avoid
damage to the seals.
10) Torqueallfour(4)bltsto240ir-lb
(27 Nm).
NOTE: Carefullystudythe
order of respective
partsandnote
positionof seals to
assureproper re-
assembly and opera-
tion.
801-457 7
.. ~. .. ..~ - . , .. ., ,...
. ~.. . . . . .. _. . ..
.. . " .. . . . . .,

8 801-457
- ..,
".. . ... ~, ~ . . .
. .. .. . . -~ .
~.
..
.. .
..

Ref. No. 50 Includesitems 51-66, 79 & 81
fj/7g
62
63
52
64
65
66
56
59
PARTS LIST 8
REF PART
NO. NO.
1
2 801-001
3 800-015
4 800-038
5 800-047
6 801-390
8 801-285
10801-140
9 801-231
11 801-129
12 801-022
13 801-131
15801.394
14 801-221
16 801-379
17 801-448
18 801-446
19 801-292
20 800-039
21 801-088
..
.’ 22 801-298
23 801-302
.DESCRIPTION CITY
HOSE
& GUNASSY. seegun
detailforparts 1
PUMP, REPLACEMENTPARTS,
includeitems 77-90
ANTIVIBRATIONFOOT
1
CHASSIS
2
ELECTRIC MOTOR ASSY
1
BRACKET.spacer
1
BELT. drive 2
1
LABEL.warning 2
LABEL.warning
LABEL, identification
1
.SCREW,machine, hex hd..
1
5/16-18
NC x 1-3/4”
PLATE,serial no.
4
1
CONNECTOR,crimp
HANDLE
2
1
SWITCH, starter 1
CORD. power (8 ft Ig)
STRAIN RELIEF 2
1
SCREW, self tapping.
RAIL STIFFNER ASSY
no. 6-32 NC x 1/2 2
SCREW,machine, hex hd,
1
5/16-18
NCx 1-1/2” 4
5/16-18
NC x 2-1/2”
SCREW,machine. hex hd.
1
SCREW,machine hex tid,
5/16-18 NCx 1” 4
.. .
REF PART
NO.
NO.
24
25
26
27
28
30
29
31
32
33
34
35
36
37
38
40
39
41
42
43
44
45
46
47
48
49
50
52
51
53
54
55
56
58
57
60
59
61
62
63
64
66
65
67
68
69
70
72
71
74
73
75
76
77
78
79
80
81
801 -082
801-081
801-023
801 -015
801
-1 39
801-024
801-025
801-012
801-367
801.241
801-004
801-381
801-135
801
-1 37
801-393
801-235
801-01
8
801-364
801.365
801 -242
801 -243
801-130
801-132
801-388
801-141
800-045
801-417
801-045
801-046
801-048
801 -047
801 -049
801-050
801-059
801-046
801 -412
801-432
801-062
801 -063
801-069
801-068
801-071
801-070
801-090
801-105
801-106
801-416
801-108
801-109
801-110
801
-1 11
801-112
801-113
801-445
801-450
800-044
801
-008
801 -465
DESCRIPTION
..6 x 30 mm
CREW. machine, hex hd.
SCREW,machine. hexhd,
S
r!A
MB x 20 mm
WASHER.
flat. 1/4
WASHER.flat, 5/16
WASHER, lock, 1/4
WASHER. lock, 5/16
NUT,hex. 5/16-18 NC
GROMMET
BUMPER
WHEEL
PULLEY, pump
HUE.pulley
PULLEY, motor
KEY, pulley
(2” lg)
AXLE
WASHER,
flat
BRACKET,tensioner
BELTGUARD.baseplate
BELTGUARD. cover
HUBCAP
PIN,cotter
LABEL,warning
RIVET,drive
LABEL. warning
LABEL. warning
LABEL,starting
UNLOADER,includes
items
51-66. 79. 81
~~
CAGE,valve
SPRING
O-RING
BALL
SEAT
. O-RING
n.m~G
UNLOADER SUE-ASSY.
HOUSSG
CYLINDER
O-RING
PLUG
HOUSING VALVE
SPRING
VALVE
SEAT
QTY
4
2
8
18
4
12
4
9
1
2
1
1
1
1
2
1
1
1
1
.
COUPLER,male quick disconnect. 1
NIPPLE,straight. brass,
1/2 NPT x 3-1/2” 1
TEE, brass, 1/2 NPT
NIPPLE,hex, steel,
1/2 x 3/8 NPT 1
1
NIPPLE,hex, brass, 1/4 x 1/2 NPT 1
PLUG.hex.brass. 3/8 NPT 1
ADAPTER, 1 /2 hose
NUT.brass,adapter
SCREEN,inlet
HOSE, coupled,
1 /2 NPT
17-1 /2” lg
LABEL. caution
O-RING
SLEEVE ASSY
LABEL
#6-32 NC x 5/16
SCREW,buttonhd,
.~ ~
(MBE)
801-457 9
. . . . . . .. . . . . .. .

PARTS LIST (continued)
REF PART D.ESCRlPTlON
NO. NO.
QTY
Items 77-90 are pump internal replacement parts.
See exploded view of pump for details.
77 ~nl-nn CAP
". ".
?E 801.028 . O-RING, cap
. _. ..
79 801-267 . DISCHARGE
80 801-030 . WASHER
81 801-031
. SEAL
82 801-032 . RETAINER
83 801-033 . WASHER
84 801-034 ~ WICK
MANIFOLD
85 801-035 . RING, retaining
86 801-036 . PLUNGER
87 801-037 . STUD
88 801-038 . RING, backup
89 801-039 .
O-RING
90 801-040 .
RETAINER, plunger
. .
1
1
3
1
3
3
3
3
3
3
3
3
3
3
Order parrs by name and number. Always give the model
number andseries letter
of the assemblyfor which you are
ordering.
ELECTRICAL SCHEMATIC
-r
801-042 SEAL KIT
INCLUDES 3 SETS
OF PARTS
77.
-86
90
SERVICE TOOLS
KEY WRFNCH Rnl-nAA
. . - . .. . . -. - - . . - - . - . .
EXTRACTOR TOOL 801-205
10 801-457
.. .. . ..... . , .
.. . . . . . . . -. ,
. .. ...... ~. ~ .. . .
..
..
.. .. ~..~
.. .
~

."
... .
ij Repair Kit 801 -083
Includes items A, B. C, D, E and F
/A) )) L @ PARTSLIST
k21
SERVICE
1. Pressaccesspin(17)fromgunhandleandremove
access plate (4) by sliding plate towards back of
fittings(12and 15) from valvebody (10); Valve
handle. Unscrew both short and long tubes with
body should now slide out
of the handle through
the access plate opening.
2. Remove the cap (14). spring
(5) and ball (A) from
the valve body
(10).
3. Remove the snap ring (e). Then remove the valve
seat
(C) and O-ring (13).
4. Removethe sleeve nut (1 1) andO-ring (E) with the
actuator rod
(F).
5. Afterinstallingthenewseat(C)andball(A),tapthe
seating between the ball and seat.
balllightly
with a hammertoassureaproper
6. Reassemble in reverse order. Use pipe sealant on
pipe threads on both short and long tubes(l2 and
151.
RE
N<
:F PART
). NO.DESCRIPTION an
5
6
7
8
10
11
13
12
14
15
16
17
9
18
19
21
20
22
..
23
24
25
26
27
28
801 -007
800-043
801-250
SPRAY HOSE, 3/8" ID, 50 ft.
SPRAYGUN, (replaceable parts
include items 3-18)
HANDLE
ACCESS PLATE
SPRING
TRIGGER
. NEEDLE
(1 5 m) IQ
. HEX PLUG
. DISCHARGE FllTlNG
. VALVE BODY
. GUIDE SLEEVE
. TUBE
. INLET FllTlNG
. CAP
'801 -090
801 -073
'801 -01
0
"801-011
801-074
801-103
*a01
-091
.
. SAFETY LATCH
. ACCESS PIN
. LATCH PIN
TUBE,
32"
COUPLER, female quick disconnect
GRIP
HOUSING,
nozzle
COUPLER, male quick disconnect
TIP, cleaning; 150
TIP, blasting; 0"
GUARD, tip
NIPPLE, hex; 1/4 x 3/8" npt; brass
COUPLER, male quick disconnect
1
1
1
1
1
1
1
1
1
1
1
1
1
Orderparts byname and series letter of the assembly for
which you are ordering.
*Recommended "tool box" spare parts.
801.457 11
. . .. _.

ACCESSORIES (Must be purchased separately)
CHECK VALVE 801 -1 33 CHEMICALINJECTOR KIT 800-102
Prevent back up of contaminatedwaterintofresh For injecting harsh cleaning chemicals downstream
supply.Installupstreamfrompump. from pump.
WATER SANDBLASTER 800-1 03 ADJUSTABLE SAND SAVER 801-031
For abrasivecleaning of stubborndirtandpaint. For adjustingsandflow.
TECHNICAL DATA
MOTOR: 5 hp, 1phase
220V.
60 Hz, 27.5 Amp
WATER PUMP: 2150 PSI (150bar) max
pressure;
4 G,PM
(15liter/min).
WETTED PARTS: StainlessSteel,Aluminum,
Phenolic Plastic, Ceramic
Liners, Nitrile Rubber.
WEIGHT: 195 Ibs
(88 kg)
OVERALLDIMENSION:Length:
38 in (965mm)
Width:27
in (686mm)
Height:26
in (660 mm)
MAX. WATER TEMPERATURE: 16OoF (70°C)
INLET HOSE CONNECTION: 3/4-in. gardenhose (f)
THE GRACO WARRANTY
GracoInc.warrantsallequipmentmanufacturedbyitandbear~ngitsnametobefreeframdefectsin
material and workmanship under normal use and service. This warranty extends to the original
purchaserforaperiodof12monthsfromthedateofpurchaseandappliesanlywhentheequipment
is installed and operated inaccordance with writtenfactaryrecommendations.This warrantydoes
abrasion. corrosion. negligence, accident. substitution of non-Graco parts. faultyinstallation or
not cover damage or wear which. in the reasonable judgment of Graco. arises from misuse.
tampering.
This warranty is conditioned upon theprepaid returnof the equipment clatmed
to be defective for
examinationby Graco toverify the claimeddefect.If the claimeddefectisverified. Gracowill repair
or replace free of charge. any defective parts. The equipment will be returned IO the original
purchaser transportation prepaid. If inspection
of the equipment does not disclose any defect in
workmanship or material,repairs willbe madeata reasonablechargeandreturntranspartationwill
be charged.
..............
PURPOSEAND OF ANYNON-CONTR
EOUIPMENTNOTCOVERED
BY GRACOWARRANTY. Accessories or components of equipment
soldbvGracothat
are not manufactured byGraco(such aselectricmotors. switches. hose.etc.)are
subject
to the warranty. if any. of their manufacturer.Gracowillprovidepurchaser wcth reasonable
assistance inmaking such claims.
Subsidiary and AffiliateCompanies: Canada: England; Switzerland; France; Germany; Hong Kong: Japan
Factory Branches: Atlanta. Pallas, Detroit, Lo6 Angeles. West Caldweli 1N.J.l
GRACO INC. P.Q. BOX 1441 MORIRIEAPQLIS, MRI 55440-1444
PRINTED IN U.S.A. 801.457 Rev A 7/83
45-10051A
. .~ . ..........
- .. ........
..... ." .....