GrainWood MC0705 User manual

19 ¼"
34 ½"
51 ¾"
Assembly Instructions
MC0705 Brushed Walnut
Finish
Model #
Thank you for choosing Grain Wood Furniture, it is an honor to be in your home!
If you have any questions, feedback, or need replacement parts please contact us at:
grainwoodfurniture.com/help or [email protected]
2-person assembly
PH #2
Made in Brazil
REV - 06/2021 page 1/14
Mid Century
5-Drawer Chest

ŸEnlist help from a friend or family member as most items require two
people for proper assembly.
ŸChoose a spacious, open area near where the piece will be located once
assembled. It is easier to move parts than to relocate the furniture after it
is fully assembled.
ŸDo not throw away packaging material until assembly is complete.
ŸAssemble the item on a soft surface, such as cardboard or an old blanket
in order to protect the finish from possible dents or scratches.
ŸLay out the parts in order and count them twice. In case any parts are
missing or damaged, document the problem with pictures and contact
support so we can make it right.
ŸSolid wood furniture may present imperfections such as wood knots,
minor splits or cracks which are a natural aspect of the material.
Whenever stability of the furniture is not compromised, we recommend
customers perform cosmetic touch-ups with wax crayon fillers sold at all
major hardware stores.
ŸIt is best to use the tools provided in the box, such as a hex key, because
they may be specially sized for the piece of furniture.
ŸWe do not recommend the use of power drills as they can damage your
furniture if not used correctly.
ŸUse a carpenter's square or hardcover book to check angles when
assembling drawers and doors. If they are not at 90 degrees, they will not
close properly.
ŸIf you have any problems, we are here to help. Just go to
grainwoodfurniture.com/help.
ŸSee grainwoodfurniture.com/care-guide for suggestions that will help
your furniture last for years.
Enjoy your 100% solid wood furniture!
PLEASE READ BELOW BEFORE BEGINNING ASSEMBLY
page 2/14

4,0x30 50 + 2
3,5x14 16 + 1
8,0x30 56 + 3
4,0x45 8 + 1
6,0x10 40 + 2
A1
A4
C1
A40
B31
A8 3,0x20 2 + 1
F9 1
F8 2
ANTI-TIPPING RESTRAINT KIT
450mm - 17 3/4"
450mm - 17 3/4"
1/4’’x40
4
B25
5/16"x24x2 4 + 1D41
5
E17
5
E17
M4x25 10 + 1A25
G1 10x10 28
G8 1
H16 10
G14 4
450mm - 17 3/4"
450mm - 17 3/4"
5
E18
5
E18
RIGHT
Side
Drawer
RIGHT
LEFT
Side
Drawer
LEFT
HARDWARE LIST
page 3/14
Before starting assembly
please verify the hardware
set is complete.
For missing hardware please
contact us at
grainwoodfurniture.com/help
WARNING:
CHOKING HAZARD
Small parts, not for children.
To be assembled by an adult.
!ATTENTION

5x
12 09
11
13
10
02
03
01
14
06
07
04
14
15
05
05
05
05
08
page 4/14
Part # Part #
Qty. Qty.
DescriptionDescription
03 1
Right side
02 1
Left side
09
12
14
15
HW
5
5
5
2
1
Drawer right side
Drawer Left side
Drawer back
Back panel
Profile “H”
1
Hardware
10
Top
04 1
01 1
Base
05
06
07
08
11
13
4
1
1
5
5
5
Foot
Stabilizing panel
Rear panel
Drawer front
Drawer bottom
Drawer bottom support
BOX A - 1 of 2 BOX B - 2 of 2

C1 8,0x30 56
1)
2)
B31 6,0x10 20 E17
450mm - 17 3/4
5
RIGHT
Side
450mm - 17 3/4"
5
E18
LEFT
Side
C1
C1
03
C1 C1
C1
C1 C1
C1
C1 C1
C1
C1 C1
C1
C1
C1
C1
C1
C1
C1
C1
C1C1
C1C1
02
06
13
10
09
5x
5x
03
B31
02
B31
B31
B31
B31
B31
B31
B31
B31
B31
B31
B31
B31
B31
B31
B31
B31
B31
B31
B31
E17
E18
E17
E17
E17
E17
E18
E18
E18
E18
E18 B31
03 02
02
03
E17
B31
03
02
E17
E18
B31 B31
!
Tip :
Use a hammer in case dowels
are hard to install by hand.
page 5/14

4)
A1 4,0x30 4
B25 1/4"x40 4D41 5/16"x24 4G8 1
06
03
02
A1
A1
A1
A1
A1
page 6/14
04
G8+B25
05
05
05
05
D41
G8+B25
G8+B25
G8+B25
D41
D41
D41
3)
D41
G8
B25
04
Attention: There are
no predrilled holes
for the A1 screws on
parts 02 and 03.
!

5)
6)
04
A1 4,0x30 6
01
A1
A1
02
06
03
A1
A1
A1
A40 4,0x45 6
A40
A40
A40
A40
A40
A40
page 7/14
Attention: There
are no predrilled
holes for the A1
screws on part 01.
Attention: There are
no predrilled holes
for the A40 screws
on parts 02 and 03.
02
03
03
04
A40
!
!
A1

7)
G1 10x10 4
8)
ü
!
G1
û
!
G1
ü
!G1
G1
G1
G1 10x10 4
G1
G1
G1
G1
G1
G1 G1
G1
14
14
14
14
Make sure back panels are perfectly aligned with
side panels and top and there are NO gaps.
page 8/14
!
ü
G1
!
û
G1

9)
10)
G14 4
G1 10x10 12
15
14
14
14
14
15
G14
G14
G14
G14
G14
07
G1
G1
G1
G1
G1
G1
G1
G1
G1
G1
G1
G1
07
04
!
page 9/14

11)
12)
3,5x14
A4 10
G1
G1
07
A4
A4
A4
A4
A4
A4
A4
07
14
14
14
G1
G1
G1
G1
G1
G1
G1
A4
A4
A4
A4
A4
A4
A4
A4
A4
A4
A4
page 10/14
3,5x14
A4 6G1 10x10 8
A40 4,0x45 2
A40
A40
Attention: There are no
predrilled holes for the A4
and A40 screws on part 07.