GrainWood Shaker SH0501 User manual

18”
63 ¾”
32”
Assembly Instructions
SH0501
SH0502
Cherry
Expresso
Finish
Model #
Thank you for choosing Grain Wood Furniture, it is an honor to be in your home!
If you have any questions, feedback, or need replacement parts please contact us at:
grainwoodfurniture.com/help or [email protected]
2-person assembly
PH #2
Made in Brazil
REV - 06/2021 page 1/14
Shaker Collection
6-Drawer Dresser
SH0504 Walnut

page 2/14
ŸEnlist help from a friend or family member as most items require two
people for proper assembly.
ŸChoose a spacious, open area near where the piece will be located once
assembled. It is easier to move parts than to relocate the furniture after it
is fully assembled.
ŸDo not throw away packaging material until assembly is complete.
ŸAssemble the item on a soft surface, such as cardboard or an old blanket
in order to protect the finish from possible dents or scratches.
ŸLay out the parts in order and count them twice. In case any parts are
missing or damaged, document the problem with pictures and contact
support so we can make it right.
ŸSolid wood furniture may present imperfections such as wood knots,
minor splits or cracks which are a natural aspect of the material.
Whenever stability of the furniture is not compromised, we recommend
customers perform cosmetic touch-ups with wax crayon fillers sold at all
major hardware stores.
ŸIt is best to use the tools provided in the box, such as a hex key, because
they may be specially sized for the piece of furniture.
ŸWe do not recommend the use of power drills as they can damage your
furniture if not used correctly.
ŸUse a carpenter's square or hardcover book to check angles when
assembling drawers and doors. If they are not at 90 degrees, they will not
close properly.
ŸIf you have any problems, we are here to help. Just go to
grainwoodfurniture.com/help.
ŸSee grainwoodfurniture.com/care-guide for suggestions that will help
your furniture last for years.
Enjoy your 100% solid wood furniture!
PLEASE READ BELOW BEFORE BEGINNING ASSEMBLY

G1 10x10 27
H4 12
G11 6
4,0x30 69 + 2
3,5x14 19 + 1
8,0x25 76 + 2
M4x25 12 + 1
1
4,0x25 1
6,0x10 48 + 2
6
6
330mm - 13"
330mm - 13"
RIGHT
Side
Drawer
RIGHT
A1
A4
C2
A25
D21
A18
B31
E13
E13
E14
E14
6
6
330mm - 13"
330mm - 13"
LEFT
Side
Drawer
LEFT
page 3/14
A8 3,0x20 2 + 1
F9 1
F8 2
ANTI-TIPPING RESTRAINT KIT
HARDWARE LIST
Before starting assembly
please verify the hardware
set is complete.
For missing hardware please
contact us at
grainwoodfurniture.com/help
WARNING:
CHOKING HAZARD
Small parts, not for children.
To be assembled by an adult.
!ATTENTION

6x
01
02
03
08
09
10
11
12
13
14
04
04
05
06
06
07
07
15
01 1
Top
03 1
02
Right side
1
04 2
Left side
Upper crosspiece
06
09
10
14
HW
2
6
6
1
1
Rear crosspiece
Drawer right side
Drawer left side
13 6
Drawer bottom support Division
Part # Description Qty. Part # Description Qty.
Hardware
07 2
Back panel
08 6
Drawer front
05 1
Lower crosspiece
11 6
Drawer bottom
12 6
Drawer back
15 1
Profile “H”
page 4/14
BOX A - 1 of 2 BOX B - 2 of 2

03
02
E14
B31
B31
B31
E14
E14 B31
B31
B31
E13
E13
E13
B31
B31
B31
B31
B31
B31
1)
C2 8,0x25 76 D21 1
2)
C2
6x
03
02
14
09
6x
10
C2
C2
C2
C2
C2
C2
C2
C2
C2
D21
C2 C2
6x
13
C2C2
C2C2
05
C2C2
C2C2
2x
04
2x
06
C2C2
C2C2
C2C2
C2C2
D21
B31
E13
B31
330mm - 13"
3
B31 6,0x10 12 E13
330mm - 13"
3E14
RIGHT
Side
LEFT
Side
C2
page 5/14
Tip :
Use a hammer in case dowels
are hard to install by hand.

3)
4)
A1 4,0x30 4
A1
14
06
04
02
A1
A1
A1
A1
E14
B31
B31
B31
E14
E14
E13
E13
E13
180º
14
14
B31
B31
B31
B31
B31 B31
B31
B31
B31
330mm - 13"
3
B31 6,0x10 12 E13
330mm - 13"
3E14
RIGHT
Side
LEFT
Side
B31
E13
B31
A1 04
06
page 6/14
Attention: There are
no predrilled holes
for the A1 screws on
parts 02 and 14.

5)
6)
A1
A1
A1
A1
A1
A1
A1
A1
A1
A1 01
A18
A1 4,0x30 11 A18 1
4,0x25
A18
05
06
03
04
05
A1 4,0x30 6
A1
A1
A1
A1
A1
A1
A1
04
A1
06
page 7/14
Attention: There are
no predrilled holes
for the A1 screws on
part 01.
Attention: There are
no predrilled holes
for the A1 screws on
parts 02, 03 and 14.
Attention: There are no
predrilled holes for the
A18 screws on part 05.

7)
8)
G1 10x10 2
ü
!
G1
û
!
G1
ü
!G1
G1
!
ü
G1
!
G1
û
G1 10x10 3
G1
07
07
page 8/14
Make sure back panels are perfectly aligned with
side panels and top and there are NO gaps.

9)
10)
15
15
07
07
G11 6
G1 10x10 22
G1
page 9/14
07

A4
A4
A4
A4
A4
A4
A4
11)
12)
3,5x14
A4 12
A4
A4
A4
A4
A4
A4
A4
A4
A4
A4
A4
A4
A4
3,5x14
A4 7
A4
page 10/14
Attention: There are no
predrilled holes for the A4
screws on parts 02, 03 and 14.
Attention: There are no
predrilled holes for the A4
screws on parts 06 and 07.
07
06
06

13)
09
10
08
A1
A1
A1
11
12
A1
A1
A1
A1
12
12
13
!
1"
12
13
09
A1
A1 4,0x30 48
6x
page 11/14
Attention: There are no
predrilled holes for the
A1 screws on part 08.

14)
15)
B31
E13
E14
E13
B31
B31
B31
B31
6x
330mm - 13"
330mm - 13"
E13 6
E14 6
B31 6,0x10 24
Drawer
RIGHT
Drawer
LEFT
6x
H4 12
A25 M4x25 12
H4
A25 H4
A25
page 12/14
Flip the assembled drawer
upside down to install glides.

16)
!
page 13/14
Place the labeled drawer on the top position

17)
!
page 14/14
ANTI-TIPPING RESTRAINT KIT
A8 3,0x20 2
F9 1
F8 2
Install against the
furniture
A8
A8
F8
F8
Anchors and screws are not included,
choose best type based on your wall
on the wall
F9
WALLBOARDWALLBOARD
Install both parts F8
Tighten them together
using the safety strap
F8