Grandstream Networks GDS3710 User manual

For Warranty and RMA information, please visit
www.grandstream.com
Grandstream Networks, Inc.
126 Brookline Ave, 3rd Floor
Boston, MA 02215. USA
Tel : [phone] - 9300
Fax: [phone] - 1987
www.grandstream.com In-Wall Mounting Kit
Quick Reference Guide
(GDS3710/3705 NOT Included)

Content
English......................................................1

.1. .2.
EN
PRECAUTIONS
• Please follow local building code and electrical code to
install the device.
• Suggest to install the device with bottom line 45~55 inches
(1.2~1.4 meters) above the ground lever.
• Please avoid dropping or vigorous vibrating of the device.
• Please keep device away from strong electromagnetic
field or explosive atmosphere.
• Do not open or install the device in damp environment.
Avoid using the device in very low or high temperature
environment.
• Recommend to seal the frame or wall gap with silicone or
other sealant after installation to avoid inside water leaking.
• Remove the electrostatic adsorption protective plastic film
after all installations/configurations to avoid lens cover
contamination or scratch.
• Please refer to Grnadstream website for more
updated Online Documents like:
QIG:
www.grandstream.com/sites/default/files/
Resources/GDS3705_QIG.pdf
www.grandstream.com/sites/default/files/
Resources/GDS3710_QIG.pdf
User Manual:
www.grandstream.com/sites/default/files/
Resources/GDS3705_UserManual.pdf
www.grandstream.com/sites/default/files/
Resources/GDS3710_UserManual.pdf
FAQ:
www.grandstream.com/our-products
This guide applies to both GDS3705 and GDS3710,
with GDS3710 in the illustration.
The warranty not apply to defects and failures as a result of improper
installation.
The manufacturer is neither liable for damages caused by theft within an
area that is accessible after the attached electric lock is switched. The
product is not designed as a burglar protection device except when used
in combination with a standard lock.
If the proper mounting instructions not met, water might get in and destroy
the electronics as the internal circuits are under continuous operation.
The manufacturer's warranty shall be void for products damaged in this way.

.4.
.3.
6 x Screws
(Fix Plastic box
on Meta Frame)
6 x Anti-Tamper
Screws
6 x Screws
(Fix the Bracket
into Plastic Box)
6 x Anchor & Screw
Set (Mount the Plastic
Box into Solid Wall)
6 x Nuts
(Fix Plastic Box on
the Meta Frame)
(1) (2)
(5)(4)
(3)
(4)
6 x Nuts
(Fix Plastic Box on
the Meta Frame)
PA3.5*35mm PM3*10mm PM3*12mm
M3 M3 PM3*12mm
1 x Quick
Reference Guide
1 x Anti-Tamper
Hex Key
1 x Metal Frame
(For Stud Mount)
In-Wall Mounting Kit
Quick Reference Guide
(GDS3710 NOT Included)
PACKAGE CONTENTS
1 x Cover Plate
1 x Plastic Box 1 x Drill Template

.5. .6.
(1)
(2)
PA3.5*35mm
PM3*10mm
Step 3: Use provided Anchor/Screw(1) to mount the
Plastic Box inside the hole just digged.
Step 2: Mount the Installation Bracket into the Plastic Box
using supplied Screws(2).
Solid Wall Installation
Please follow below steps to install the device into solid wall.
Step 1: Use provided Drill Template to mark boundary then
drill holes for the 6 mounting screws and the circular
hole for wiring. (driling or dig tools not provided)
Then dig a rectangle hole for the box with depth
around 38~43 mm (or 1.50~1.69 inch), refer to mark
in the template (rotating it to measure if necessary).
42mm(or 1.65 inch)
80mm(or 3.15 inch)
80mm(or 3.15 inch)
38~43 mm (or 1.50~1.69 inch)
18mm(or 0.71 inch)
193.8mm(or 7.63 inch)
99.8mm(or 3.93 inch)

.8..7.
(5)
PM3*12mm
Step 4:
Step 5: Follow GDS37XX QIG and User Manual to connect
wires to the PoE switch or PoE Injector. Connect the
Electrical Lock wiring acoording to its document.
Remove the frame back cover (designed for Surface/
OnWall Installation).
Step 7: Install the Cover Plate and fix it using the Hex Key
with the Anti-Tamper Screws(5) provided.
Step 6: Align the GDS37XX with the bracket, press and push
down the GDS37XX into place.
(Result after installation.
GDS37XX NOT included)

.9. .10.
(1)
(2)
(3)
(4)
PA3.5*35mm
PM3*10mm
PM3*12mm
M3
Step 4: Use provided Screws and Nuts(3)(4) to install the
Plastic Box on the long edge of the Metal Frame.
Choose either set of Nuts(4) with convenience.
or
Step 3: Mount the Installation Bracket into the Plastic Box
using supplied Screws(2).
Step 2: Install the Metal Frame with short edge to the stud
using the set of Anchor/Screw(1) provided.
35mm
(or 1.38 inch)
Stud Installation
Please follow below steps to install the device at the stud of
a new building open wall,or a finished wall.
Step 1: For finished wall, use provided Drill Template to
mark boundary and dig a rectangle hole into the
wall. For open wall, skip and go to next step.
Max: 203.2 mm(or 8 inch)

.11. .12.
(5)
PM3*12mm
Step 5:
Step 6: Follow GDS37XX QIG and User Manual to connect
wires to the PoE switch or PoE Injector. Connect the
Electrical Lock wiring acoording to its document.
Remove the frame back cover (designed for Surface/
OnWall Installation).
Align the GDS37XX with the bracket, press and push
down the GDS37XX into place.
Step 8: Install the Cover Plate and fix it using the Hex Key
with the Anti-Tamper Screws(5) provided.
Step 7:
(Result after installation.
GDS37XX NOT included)

.13. .14.
(2)
PM3*10mm
Step 3: Insert the Plastic Box into the cutted hole properly.
Step 4: Tighten the four clamps alternately in diagonal to
mount the Plastic Box on the wall. Please do NOT
over tighten to avoid damaging the wall or clamp.
Step 2: Mount the Installation Bracket into the Plastic Box
using supplied Screws(2).
Drywall (Hollow Wall) Installation
Please follow below steps to install the device on a drywall or
hollow wall. The thickness of the wall where the clamps can
handle is among 6.2 ~ 24 mm (or 0.24 ~ 0.94 inch)
Step 1: Use provided Drill Template to mark boundary then
cut opening on the dry wall. Do NOT over cut.
(wall cutting tools not provided)
193.8mm(or 7.63 inch)
99.8mm(or 3.93 inch)

.16.
(5)
PM3*12mm
.15.
Step 5:
Step 6: Follow GDS37XX QIG and User Manual to connect
wires to the PoE switch or PoE Injector. Connect the
Electrical Lock wiring acoording to its document.
Remove the frame back cover (designed for Surface/
OnWall Installation).
(Result after installation.
GDS37XX NOT included)
Install the Cover Plate and fix it using the Hex Key
with the Anti-Tamper Screws(5) provided.
Step 8:
Step 7: Align the GDS37XX with the bracket, press and push
down the GDS37XX into place.