Grandstream Networks GDS3710 User manual

Grandstream Networks, Inc.
GDS3710 Input/output Alarms
Configuration Guide

P a g e | 2
GDS3710 Input/output Alarms
Configuration Guide
Table of Contents
INTRODUCTION .............................................................................................................4
GDS3710 WIRING CONNECTION .................................................................................5
Powering GDS3710 .................................................................................................................5
Power and Data PINs ........................................................................................................................... 5
Connecting Alarm IN and Alarm OUT PINs ..............................................................................6
Alarm IN Connection Example.............................................................................................................. 8
Alarm OUT Connection Example.......................................................................................................... 9
GDS3710 ALARM CONFIGURATION ..........................................................................10
Alarm Schedule...................................................................................................................... 11
Alarm Action...........................................................................................................................13
Alarm Phone List....................................................................................................................14
Alarm Events Config ..............................................................................................................14
Motion Detection ................................................................................................................................. 16
Digital Input ......................................................................................................................................... 17
Alarm Output ....................................................................................................................................... 17
Hostage Code ..................................................................................................................................... 17
Tamper Alarm...................................................................................................................................... 18
Keypad Input Error Alarm ................................................................................................................... 18

P a g e | 3
GDS3710 Input/output Alarms
Configuration Guide
Table of Figures
Figure 1: Connection Example ..................................................................................................................... 5
Figure 2: GDS3710 Back Cover 1 ................................................................................................................ 6
Figure 3: Connection Example 2 .................................................................................................................. 6
Figure 4: Back Cover 2 ................................................................................................................................. 7
Figure 5: Alarm Input Example ..................................................................................................................... 8
Figure 6: Alarm Output Example .................................................................................................................. 9
Figure 7: Peripheral Connections for GDS3710 ......................................................................................... 10
Figure 8: Alarm Config Page Settings .........................................................................................................11
Figure 9: Alarm Schedule ........................................................................................................................... 12
Figure 10: Edit Schedule ............................................................................................................................ 12
Figure 11: Alarm Action............................................................................................................................... 13
Figure 12: Edit Alarm Action ....................................................................................................................... 13
Figure 13: Alarm Phone List ....................................................................................................................... 14
Figure 14: Events Page .............................................................................................................................. 15
Figure 15: Region Config............................................................................................................................ 16
Figure 16: Digital Input................................................................................................................................ 17
Table of Tables
Table 1: Alarm Actions ................................................................................................................................ 13
Table 2: Alarm Phone List ........................................................................................................................... 14
Table 3: Motion Detection ........................................................................................................................... 16
Table 4: Digital Input ................................................................................................................................... 17
Table 5: Hostage Code Alarm ..................................................................................................................... 17
Table 6: Tamper Alarm ................................................................................................................................ 18
Table 7: Keypad Input Error Alarm.............................................................................................................. 18

P a g e | 4
GDS3710 Input/output Alarms
Configuration Guide
INTRODUCTION
GDS3710 HD IP Video Door System is a hemispheric IP video door phone and a high-definition IP
surveillance. GDS3710 is ideal for monitoring from wall to wall without blind spots. Powered by an advanced
Image Sensor Processor (ISP) and state of the art image algorithms, it delivers exceptional performance in
all lighting conditions. The GDS3710 IP video door system features industry-leading SIP/VoIP for 2-way
audio and video streaming to smart phones and SIP phones. It contains integrated PoE, LEDs, HD
loudspeaker, RFID card reader, motion detector, lighting control switch, Alarm input/output and more.
This guide explains step by step how to use the GDS3710 Input/Output Alarms and related configuration.

P a g e | 5
GDS3710 Input/output Alarms
Configuration Guide
GDS3710 WIRING CONNECTION
The first step to setup the GDS3710 in an environment is to choose the powering method then and connect
an RJ45 cable so it can interact with the network and start operating. Two ways are possible to power the
GDS3710 using PoE or PSU:
Using PoE as power supply (Suggested)
•Connect the other end of the RJ45 cable to the PoE switch.
•PoE injector can be used if PoE switch is not available.
Using the Power Adapter as power supply (PSU not provided)
•Connect the other end of the RJ45 cable to network switch or router.
•Connect DC 12V power source via related cable to the corrected PIN of the GDS3710.
Powering GDS3710
Below figures provide description of wiring connection of the GDS3710 Back Cover to connect the
GDS3710 with RJ45 cable and PSU and Alarm for door systems.
Power and Data PINs
To power the GDS3710 using PoE, please follow steps below:
1. Cut into the plastic sheath of your RJ45 cable, then unwind and pair the colors like shown
below.
Figure 1: Connection Example
2. Connect each color of the RJ45 to its associate on the Back Cover of the GDS3710.

P a g e | 6
GDS3710 Input/output Alarms
Configuration Guide
Figure 2: GDS3710 Back Cover 1
To power the GDS3710 using PSU, please follow steps below:
1. Use a multimeter to detect the polarity of your Power Supply, then connect the Back Cover
GND to negative pole and 12V to positive pole of the PSU.
2. Cut into the plastic sheath of your RJ45 cable, then unwind and pair the colors like shown
below
Figure 3: Connection Example 2
3. Connect wires OrangeWhite/Orange and GreenWhite/Green of the RJ45 to its associate on
the GDS3710
Note: The Blue and Brown PINs are used for PoE, therefore when using PSU we only need to connect the
data wires, power will be provided to the GDS3710 trough (12V, GND).
Connecting Alarm IN and Alarm OUT PINs
The GDS3710 have two alarm input entries and two alarm output entries and a ground entry as shown in
the following figure.

P a g e | 7
GDS3710 Input/output Alarms
Configuration Guide
Figure 4: Back Cover 2
The following table summarizes the GDS3710 entries and their purpose.
Jack
Pin
Signal
Function
Note
J2
(Basic)
3.81mm
1
TX+
Ethernet
PoE 802.3af
Class 3, 12.95W
Orange / White
Data
2
TX-
Orange
3
RX+
Green / White
4
RX-
Green
5
PoE_SP2
Blue + Blue/White
Please twist these two wires
together and connect to SP1,
SP2 respectively even the
PoE NOT used.
6
PoE_SP1
Brown + Brown/White
7
RS485_B
RS485
8
RS485_A
9
GND
Power Supply
DC 12V, 1A Minimum
10
12V
J3
(Advanced)
3.81mm
1
GND
Alarm GND
2
ALARM1_IN+
Alarm In
Vin<15V
3
ALARM1_IN-
4
ALARM2_IN+
5
ALARM2_IN-
6
NO1
Alarm Out
Relay: 30VDC/2A; 125VAC/0.5A
7
COM1
8
NO2
Electric Lock
For "Fail Secure" (Locked when Power Lost) Strike,
Connecting COM2 & NO2;
For "Fail Safe" (Open when No Power) Magnetic Lock,
Connecting COM2 & NC2.
Relay: 30VDC/2A; 125VAC/0.5A
9
COM2
10
NC2

P a g e | 8
GDS3710 Input/output Alarms
Configuration Guide
J4
(Special)
2.0mm
1
GND
Wiegand Power
GND
Black
Both Input and Output
MUST be connected
2
WG_D1_OUT
Wiegand Output
Signal
Orange
GDS3710 function as Output
of Card Reader, Connect Pin
1, 2, 3
3
WG_D0_OUT
Brown
4
LED
Wiegand Output
LED Signal
Blue
For External Card Reader; Or
GDS3710 as Receiver Only
5
WG_D1_IN
Wiegand Input
Signal
White
For External Card Reader
Connect Pin 1,4,5,6,7,8
6
WG_D0_IN
Green
7
BEEP
Wiegand Output
BEEP Signal
Yellow
For External Reader Only
8
5V
Wiegand Power
Output
Red
For External Card Reader
Only.
12VDC powered External
Card Reader must use own
power source, can NOT use
this Pin.
Note:
Alarm IN and Alarm OUT are just electronic lock, they are either open to block the current or close to let
the current pass through, therefore a 3rd party power supply is needed to power the device connected to
the GDS3710 via Alarm IN or Alarm OUT.
Alarm IN Connection Example
Connect Alarm (IN1+, IN1-) or (IN2+, IN2-) to appropriate wires in order to receive signal from the third
party device as shown below.
Figure 5: Alarm Input Example

P a g e | 9
GDS3710 Input/output Alarms
Configuration Guide
Alarm OUT Connection Example
Connect Alarm (NO1, COM1) to appropriate wires in order to receive signal from the third party device as
shown below.
Figure 6: Alarm Output Example
Note:
Please refer to GDS3710 User Manual for information to detect and access the GDS web GUI.

P a g e | 10
GDS3710 Input/output Alarms
Configuration Guide
GDS3710 ALARM CONFIGURATION
The below diagram illustrates an example of peripheral connections for the GDS3710.
Figure 7: Peripheral Connections for GDS3710

P a g e | 11
GDS3710 Input/output Alarms
Configuration Guide
To configure the Alarm IN/OUT on the GDS3710, access the webGUI, after detecting the GDS3710 IP
address using one of the methods previously mentioned, and log in as admin (the default user/pass for
admin log in is admin/admin).
Navigate to “Alarm Config”, this tab contains four sub sections as shown below.
Figure 8: Alarm Config Page Settings
Alarm Schedule
This page specifies the configuration of Alarm Schedule.
Schedule must be in place before the alarm take the related action.

P a g e | 12
GDS3710 Input/output Alarms
Configuration Guide
Figure 9: Alarm Schedule
GDS3710 supports up to 10 alarm schedules to be configured, with time span specified by users. User can
edit the alarm schedule by clicking button. Usually the 24 hours’ span is 00:00 ~ 23:59, which is 24
hours’ format.
Users can copy the configuration to different date during the schedule programming.
Figure 10: Edit Schedule

P a g e | 13
GDS3710 Input/output Alarms
Configuration Guide
Alarm Action
This page specifies the configuration of Profile used by the Alarm Actions. A Profile is required before the
Alarm Action can take effect.
Figure 11: Alarm Action
User can edit the alarm action by clicking button, the following window will popup.
Figure 12: Edit Alarm Action
Table 1: Alarm Actions
Upload to Alarm Center
When checked, the alarm video will be transferred to Alarm Center.
Voice Alarm to SIP
Phone
If the SIP server or the peer IP device is configured, check this will allow
the event to trigger alarm SIP call to pre-configured number.

P a g e | 14
GDS3710 Input/output Alarms
Configuration Guide
Send Email
When checked, an email will be sent when the events are triggered to the
pre-configured email account.
Sound Alarm
When selected, alarm will be played from the GDS3710 Built-in Speaker.
Alarm Output
An alarm will be sent to the Alarm Output interface if this option is
checked.
Upload JPEG
When checked, snapshots of the moment where the event is triggered will
be uploaded to the FTP server.
Alarm Phone List
This page allows user to configure the Alarm Phone List, which is phone numbers or extensions list that the
GDS3710 will call out when event trigged (e.g.: doorbell pressed).
Figure 13: Alarm Phone List
Table 2: Alarm Phone List
Add
Add new phone number to the alarm list.
Delete
Delete a number from the phone alarm list.
Once the event is triggered (Motion Detection, Door Bell Pressed…) the GDS3710 will call the first number,
once time out is reached and no answer is returned from the first number, the GDS3710 will try the next
number on the list and so on. Once the remote phone answers the call an alarm will be played to notify
users that an event is triggered.
Alarm Events Config
This page allows users to configure GDS3710 events to trigger programmed actions within predefined
schedule.

P a g e | 15
GDS3710 Input/output Alarms
Configuration Guide
Figure 14: Events Page
Alarm can be triggered either by motion detection or by GDS3710 input.

P a g e | 16
GDS3710 Input/output Alarms
Configuration Guide
Motion Detection
Users can select a specific region to trigger the alarm using motion detection.
Figure 15: Region Config
Table 3: Motion Detection
Enable Motion Detection
Click on the check box to enable Motion Detection.
Region Config
Click to enter the Region Config menu.
Quit Config
Click to exit the Region Config menu.
Clear Selected Region
Select a zone on the screen then click on Clear to delete the region.
Sensitivity
Region sensitivity (value between 0-100%).
Select Alarm Schedule
Select the Schedule programmed.
Select Alarm Action Profile
Select the programmed Alarm Action.

P a g e | 17
GDS3710 Input/output Alarms
Configuration Guide
Digital Input
Figure 16: Digital Input
Table 4: Digital Input
Digital Input 1
Select the Input method (alarm Input or Door Open).
Select Alarm Schedule 1
Select the predefined Schedule.
Select Alarm Action Profile 1
Select the predefined Alarm Action.
Digital Input 2
Select the Input method (alarm Input or Door Open).
Select Alarm Schedule 2
Select the predefined Schedule.
Select Alarm Action Profile 2
Select the predefined Alarm Action.
Alarm Output
Alarm Output Duration(s) specifies how long the alarm output will take effect.
The valid range is 5 to 300 seconds.
Hostage Code
Hostage password can be used in a critical situation for instance a kidnaping or an emergency, users need
to enter the following sequence to trigger the actions set for the Hostage Mode: “* HostagePassword #”.
Table 5: Hostage Code Alarm
Enable Hostage Password
Enable/Disable Hostage password mode.
Hostage Code
Set the password for the hostage mode.
Select Alarm Action Profile
Select the Alarm action to be taken when the hostage password is
typed on the GDS3710 keypad.
Note: No sound alarm will be triggered in this mode.

P a g e | 18
GDS3710 Input/output Alarms
Configuration Guide
Tamper Alarm
Tamper alarm is anti-hack from Hardware level. When this option is checked, if the GDS3710 is removed
from the installation board, it will generate the alarm actions configured. There is an embedded mechanism
on the GDS3710 that allow it to sense when the it is removed.
Table 6: Tamper Alarm
Enable Tamper Alarm
When activating this mode, GDS3710 will keep alarming until the
alarm is dismissed.
Select alarm Action Profile
Select the type of alarms to be taken for the tamper alarm mode.
Keypad Input Error Alarm
Table 7: Keypad Input Error Alarm
Enable Keypad Input Error
Alarm
Enable/Disable the Input Error Alarm, GDS3710 will take alarm actions
every 5 incorrect attempts.
Select Alarm Profile
Select the Alarm action to be taken after 5 incorrect attempts.