Grandstream Networks GDS3710 User manual

Grandstream Networks, Inc.
Connecting GDS3710 with GXP IP Phones
Configuration Guide

Connecting GDS3710 with GXP IP Phones
Configuration Guide
P a g e | 2
Table of Contents
SUPPORTED DEVICES .................................................................................................3
INTRODUCTION.............................................................................................................4
PEERING SCENARIO ....................................................................................................5
GDS3710 Configuration Settings...........................................................................................................5
GXP IP Phones Configuration ...............................................................................................................7
CONNECTION USING SIP SERVER ...........................................................................10
GDS3710 Configuration Settings.........................................................................................................10
GXP IP Phone Configuration Settings .................................................................................................12
OPEN DOOR FEATURE...............................................................................................15
GXP21xx IP Phones ............................................................................................................................15
GXP17xx IP Phones ............................................................................................................................16
GXP16xx IP Phones ............................................................................................................................16
Table of Figures
Figure 1: GXP IP Phones peered with the GDS3710 ...................................................................................5
Figure 2: Door System Settings ....................................................................................................................6
Figure 3: Enable Direct IP Call......................................................................................................................7
Figure 4: GXP2170 Account(x) Settings .......................................................................................................7
Figure 5: Account(x) SIP Settings .................................................................................................................8
Figure 6: GDS3710 Configuration Settings on GXP IP Phone .....................................................................9
Figure 7: GXP2170 Connected to GDS3710 through UCM6XXX ..............................................................10
Figure 8: SIP Basic Settings .......................................................................................................................11
Figure 9: Door System Settings ..................................................................................................................12
Figure 10: General Settings ........................................................................................................................13
Figure 11: GDS Settings .............................................................................................................................14
Figure 12: GDS3710 Video/Audio Call on GXP2170..................................................................................15
Figure 13: GDS3710 Audio Call on GXP1760 (Using SIP Server Scenario)..............................................16
Figure 14: GDS3710 Audio Call on GXP1630 in Peering Scenario............................................................16

Connecting GDS3710 with GXP IP Phones Configuration Guide
P a g e | 3
SUPPORTED DEVICES
Following table shows Grandstream products supporting GDS3710 integration:
Model
Supported
Firmware
Audio
Video (JPEG)
GXP16XX Series
Yes
No
1.0.4.65 or higher
GXP17XX Series
Yes
No
1.0.1.28 or higher
GXP21XX Series
Yes
Yes
1.0.8.49 or higher

Connecting GDS3710 with GXP IP Phones
Configuration Guide
P a g e | 4
INTRODUCTION
GDS3710 HD is an IP video door system with a built-in hemispheric camera and some high-definition video
capabilities. GDS3710 is ideal for monitoring from wall to wall without blind spots. Powered by an advanced
Image Sensor Processor (ISP) and state of the art image algorithms, it delivers exceptional performance in
all lighting conditions. It contains integrated PoE, LEDs, HD loudspeaker, RFID card reader, motion detector,
lighting control switch, Alarm Input/output and more.
The GDS3710 IP video door system features industry-leading SIP/VoIP for 2-way audio and video
streaming to smart phones and SIP phones, allowing to receive calls from GDS3710 on associated SIP
phones when doorbell is pressed, opening door from the SIP phone, initiate calls from the phone to
GDS3710 to get real time Video/Audio stream with GXP21xx IP Phones and only Audio stream with
GXP17xx and GXP16xx IP Phones.
The GDS3710 can be connected with a SIP phone in 2 different ways, either using peering mode (without
a SIP server) or through a SIP server/registrar.
This guide illustrates needed configuration for integrating the GDS3710 with GXP Series for both peering
and using SIP server scenarios.

Connecting GDS3710 with GXP IP Phones Configuration Guide
P a g e | 5
PEERING SCENARIO
In this scenario, we assume that the GDS3710 is installed on a small warehouse at front door and GXP IP
Phone inside to monitor and control the access of the premise. Visitors need to press the doorbell button
on the GDS3710 to initiate a video/audio call or only an audio call (depending on what the GXP Phone
supports), and the related person at the GXP IP Phone side can open the door remotely to allow the visitors
to get in as shown in the figure below.
Figure 1: GXP IP Phones peered with the GDS3710
- The IP address used by the GDS3710 is 192.168.6.135.
- The IP address used by the GXP IP Phone is 192.168.6.62.
GDS3710 Configuration Settings
The GDS3710 needs to be configured with the IP address of the GXP IP Phone, the related SIP port, and
remote PIN for door opening. Please refer to following configuration steps:
1. Access the GDS3710 Web GUI and navigate to “Door System SettingsBasic Settings”.
IP: 192.168.6.62
GDS3710
IP: 192.168.6.135
Front Door
Ethernet PoE connection
Power connection
Ethernet cable
GXP17xx
GXP16xx
GXP21xx

Connecting GDS3710 with GXP IP Phones
Configuration Guide
P a g e | 6
2. Choose the action to be taken when the doorbell is pressed, three options are available:
•Call Doorbell Number: when Doorbell is pressed, a call will be made to the “Number Called
When Door Bell Pressed”
•Control Doorbell Output (Digital Output 1): when Door Bell is pressed electronic lock for
Output 1 is opened.
•Both of Above: When selected, both Call Doorbell Number and Control Doorbell Output
options are enabled. In our case we will choose “Call Doorbell Number”.
3. Under Number Called When Door Bell Pressed field, enter the GXP IP address and port number
which is 192.168.6.62:5060 in our example.
4. Enter the “Remote PIN to Open the Door” in order to open the door via DTMF while in active call
with the GDS3710, the remote PIN used in our example is “123456”.
5. Click button to apply changes.
Figure 2: Door System Settings
6. You need to make sure that the Direct IP Call feature is enabled from the GDS3710 Web GUI under
SIP SettingsSIP Advanced SettingsEnable Direct IP Call.

Connecting GDS3710 with GXP IP Phones Configuration Guide
P a g e | 7
Figure 3: Enable Direct IP Call
GXP IP Phones Configuration
The GXP IP Phone related account needs to be set as “Active”, and the “Local SIP Port” needs to match
the port configured on GDS3710. Please refer to following steps for configuring the GXP IP Phone in order
to interconnect with the GDS3710.
1. Access GXP IP Phone Web GUIAccountGeneral Settings and set “Account Active” to Yes,
then click on button to apply the new changes.
Figure 4: GXP2170 Account(x) Settings
2. Navigate to AccountSIP Settings and verify that the Local SIP Port configured on the GXP IP
Phone is the same as the one on the GDS3710.

Connecting GDS3710 with GXP IP Phones
Configuration Guide
P a g e | 8
Figure 5: Account(x) SIP Settings
3. Navigate to SettingsExternal Service to configure GDS settings as explained on the following:
•Set the Service Type to GDS.
•Select the related account, in our example, the account used is Account 1.
•Specifies the System Identification, to identify the GDS3710, in our example its
“GDS3710_Front_Door”.
•Specifies the System Number which is the GDS3710 number, the system number used in
our example is 192.168.6.135.
•Configures the Access Password for opening the door remotely and it should match the
password configured under “Remote PIN to Open the Door” on the GDS3710 Web GUI
settings. The password used in our example is “123456”.

Connecting GDS3710 with GXP IP Phones Configuration Guide
P a g e | 9
Figure 6: GDS3710 Configuration Settings on GXP IP Phone
4. Press button to apply the new settings.
Notes:
•The GXP21xx/ GXP17xx/ GXP16xx IP Phones support up to 10 GDS3710 items.
•GXP16xx and GXP17xx series support audio only.
•GXP21xx series support audio and video (JPEG) when integrated with GDS3710.

Connecting GDS3710 with GXP IP Phones
Configuration Guide
P a g e | 10
CONNECTION USING SIP SERVER
In this scenario, we assume that the GDS3710 is configured with a SIP account and the GXP IP Phone is
also configured with a SIP account under the same SIP server.
Note: We recommend using Stateless SIP server in this type of installations, Stateful SIP servers may not
work.
Figure 7: GXP2170 Connected to GDS3710 through UCM6XXX
- The IP address used by the GDS3710 is 192.168.6.135 and it’s configured with SIP account 2002.
- The IP address used by the GXP IP Phone is 192.168.6.62 and it is configured with SIP account
2001.
GDS3710 Configuration Settings
As mentioned on the previous diagram, the GDS3710 should be registered with a SIP account in order to
interact with the GXP IP Phone through the SIP server.
The GDS3710 SIP settings are available under the Web GUISIP SettingsSIP Basic Settings.
UCM6xxx
GXP2170
IP: 192.168.6.62
GDS3710
IP: 192.168.6.135
Front Door
SIP Account : 2002
SIP Account : 2001
Ethernet PoE connection
Power connection
Ethernet cable
GXP17xx
GXP16xx
GXP21xx

Connecting GDS3710 with GXP IP Phones Configuration Guide
P a g e | 11
Figure 8: SIP Basic Settings
After configuring the SIP account correctly, user needs to configure the door system settings as detailed on
the following steps:
1. Navigate to Door System SettingsBasic Settings then set the following:
•Doorbell Mode: Call Doorbell Number.
•Number Called When Door Bell Pressed: the GXP IP Phone number which is 2001 in
our example.
•Remote PIN to Open the Door: the remote PIN used in our example is “123456”.
2. Click button to apply changes.
The following figure shows an example of the configuration.

Connecting GDS3710 with GXP IP Phones
Configuration Guide
P a g e | 12
Figure 9: Door System Settings
GXP IP Phone Configuration Settings
A SIP account needs to be registered on the GXP IP Phone side as well to interact with the GDS3710
trough the same SIP server.
The GXP IP Phone SIP settings are available under the Web GUIAccountsAccount(x)General
Settings.

Connecting GDS3710 with GXP IP Phones Configuration Guide
P a g e | 13
Figure 10: General Settings
After configuring the SIP account correctly, users need to configure the door system settings as detailed on
the following steps:
1. Navigate to SettingsExternal Service and set the following:
•Set the Service Type to GDS.
•Select the related account, in our example, the account used is Account 1.
•Specifies the System Identification, to identify the GDS3710, in our example its
“GDS3710_Front_Door”.
•Specifies the System Number which is the GDS3710 number, the system number used in our
example is 2002.
•Configures the Access Password which is the “Remote PIN to Open the Door” configured
on the GDS3710 Web GUI settings. The password used in our example is “123456”.
2. Press button to apply the new settings.

Connecting GDS3710 with GXP IP Phones
Configuration Guide
P a g e | 14
Figure 11: GDS Settings
Notes:
•The GXP21xx/ GXP17xx/ GXP16xx IP Phones support up to 10 GDS3710 items.
•GXP16xx and GXP17xx series support audio only.
•GXP21xx series support audio and video (JPEG) when integrated with GDS3710.

Connecting GDS3710 with GXP IP Phones Configuration Guide
P a g e | 15
OPEN DOOR FEATURE
GXP IP Phones offer a powerful integration with GDS3710 Door System and allow users to remotely open
the door, initiate calls to the GDS3710 and get real time audio/video or only audio stream.
Once someone presses the ring button on the GDS3710, the door system will initiate automatically a call
to the configured destination. In both cases, the users will have the ability to either answer the call, reject it
or press the OpenDoor softkey.
Users can open the door using the following methods:
1. Pressing the “OpenDoor” Softkey without answering the call:
Once the users press the “OpenDoor” softkey, a SIP Message containing the code for “Remote PIN
for Open the Door” will be sent to the GDS3710 to remotely open the door.
2. OpenDoor after answering the call:
•Press the “OpenDoor” Softkey, then a SIP Message containing the code for “Remote PIN for
Open the Door” will be sent to the GDS3710 to remotely open the door.
•Dial the code for “Remote PIN for Open the Door” followed by “#” (for example “123456#”),
and then DTMF codes will be sent to open the door.
Note: Pressing the “Reject” Softkey will reject the call received from the GDS3710.
GXP21xx IP Phones
Figure 12: GDS3710 Video/Audio Call on GXP2170

Connecting GDS3710 with GXP IP Phones
Configuration Guide
P a g e | 16
GXP17xx IP Phones
Figure 13: GDS3710 Audio Call on GXP1760 (Using SIP Server Scenario)
GXP16xx IP Phones
Figure 14: GDS3710 Audio Call on GXP1630 in Peering Scenario