GRAUPNER MZ-8 User manual

P1
mz-8 HoTT
◎GRAUPNER
8th F, 202 Dong, Chunui Techno-Park II, 202,Chunui-
Dong, Wonmi-Gu,
Bucheon-Si, Gyeonggi-do, SOUTH KOREA.
TEL: [phone] FAX : [phone]
E-mail: [e-mail]
FUNCTION
Main function and Channel
Basic 4 Channels and added 6 Channels.
6 Channel is as below.
① LED : ON / OFF
-> CH8 1100us / 1900us
② SPEED : Attitude mode / Rate mode
-> CH5 1100us / 1900us
③ SNAP : Taking pictures
-> CH9 1100us (1500us nothing)
④ RECORD : Film movies
-> CH9 1900us
⑤ FLIP : Use the button on top left of image (360° FLIP)
-> CH10 1100us / 1900us
now channel 10, later channel 7, (Alpha 150 not active
in autopilot mode as soon as GPS is connected it will be
channel 6 coming home function)
⑥ 3D / EASY : Use the button on top right of image
(180° revolution and additional function)
-> CH6 1100us / 1900us
CH6, when AKRO3D is adjusted in the receiver, for
normal flight mode with GPS (Alpha 150) it will be
autopilot function
⑦ 2.4GHz Quad with 6-Axis Gyro
⑧
You can attach camera and video module by
choosing option. You can take a video on the radio
using Photo & Video button.
mz-8
Frequency band
2400MHz ~2483.5 MHz
Modulation
FHSS
Transmission output
about 1mW
Temperature range
-10 … +55 ℃
Antenna
Monopole Antenna
Battery
AA Size x 3 pcs
Operating voltage
3.6 … 4.8V
Output voltage
about 50mA
Dimension
151 x 134 x 63.7 mm
Weight
about 260g (Incl. battery)

P2
Transmitter manual
Operating transmitter
- Power on : Pull Slide switch up
- Power off : Pull Slide switch down
1) Flip Function
If you push Flip button, buzzer will ring with 0.5 seconds
intervals.
To rotate a full 360 degrees, push Flip button and when
buzzer starts ringing, move stick of transmitter to
maximum position quickly.
2) 3D & Easy Function
When you push 3D button, buzzer will ring twice with 1
second intervals.
3D function is for 180 degrees flight. To operate, use
same function with Flip.
3) Attitude Function
When you push Function button, one short sound rings.
This function is attitude control of general quad copters.
4) Rate Function
When you push Function button, two short sound rings.
You can do rotation and normal flight on 3D flight mode
with transmitter. Function is same with 3D helicopter.
Flip Button
Speed Button
Light Button
3D / Easy Button
Power Switch
Status & Function
Led
Camera Record Button
Camera Snep
Button
MZ-8
Trim
Trim

P3
LED Function
< LED arrangement of transmitter >
1) LIGHT ON / OFF Function
Yellow Led
①When the lights are off, LED stay OFF condition.
②When the lights are on, LED stay ON condition.
（default status）
2) SPEED Attitude and Rate Function
Red Led
① Attitude mode : LED stay ON condition.（default
status）
② Rate mode : LED blinks with one second intervals.
3) Camera function （Optional feature）
Green Led
① When power is switched on, stay On condition.
--> Photograph mode （default status）
② When movie button is pressed, LED blinks with one
second intervals.
--> Video mode
4) Binding and Transmitter status function.
Red Led （Status Led）
① Show Power and Binding
② If device is not bound, LED blinks with 0.5 second
intervals.
③ If device is bound, LED stay ON condition.
Status
Discription
Red LED
Green LED
Buzzer
Bind range
Bind status (No
bind)
blinking (1s)
low beep(1)
Bind Success,
on
low beep(2)
RX receive OK
on
Range Test
fast blinking
low beep(2)
/2sec
Error
Low Voltage
fast blinking
High beep(4)
/2sec
Sensor Warring
High beep(3)
/2sec
Rx Voltage,
Temp Error
fast blinking
High beep(2)
/2sec
Receive rate
low, No RX
slow blinking
High beep(1)
/2sec
Factory Error
Low beep(1)
/2sec
Normal
mode
Trim inc/dec
low beep(1)
/click
Trim 0%
High beep(1)
/click
Program
mode
Program mode
start
1 blink
low beep(1)
Program mode
exit
low beep(1)
Servo Reverse
(Normal)
1 blink
(5times)
low beep(1)
Servo Reverse
(Reverse)
2 blink
(5times)
low beep(2)
ATV 100%
High beep(1)
Fail Safe mode
start
2 blink
low beep(2)
Fail safe (trim
dn, hold)
1 blink
(5times)
low beep(1)
Fail safe (trim
up, fail)
2 blink
(5times)
High beep(1)
Stick
Calibration
Calibration
mode start
3 blink
Stick move done
3 blink
(3times)
3 blink
(3times)
low beep(2)
Dead range set
Dead
blink/3sec

P4
Normal Mode
(1) Basic Operation
- When Power on, the last used memory will be bound to
Receiver.
- In case of No Receiver connection, if you press the
button of left stick for 1sec, it will search Receiver.
- if Receiver is not searched, it will be repeated until find
Receiver, and you can bind with new Receiver by
pressing BIND/LED Switch.
(2) BIND mode
In case of no having receiver, which is already saved in
memory, then you can bind with new receiver by
pressing BIND Switch.
If Receive Signal is normal, RED LED will be turned On.
In case of Waiting Receiver or Range warning, RED
LED will be slow blinked.
(3) Range Test mode
Functional switch: Press shortly button of SPEED +
SNAP once.
After Binding with Receiver, if you shortly press this
functional Switch, Range Test mode will operate for
90sec.
While operating Range mode, if you shortly press this
switch, Range test mode will be ended.
At Range mode operation, RED LED will blink quickly
and make buzzer sound.
After 90sec, Beep sound will be occurred one time, and
enter to Main Mode.
(4) Low Battery Voltage warning
RED LED will do fast blinking. ( RED LED indicate State)
At under 3200V, Warning will be announced and at
3300V, warning will be removed.
3Cell Alkaline Battery will be used.
Important Point :
While Binding, Transmitter should always have distance
from the Receiver. At least 1m should have.
Otherwise, it might be connected to Return channel, and
do malfunction.
Program Mode (workable only at Binding condition)
(1) Condition of Basic Operation
Enter to Program mode : Press two Stick Switch
simultaneously for 2sec.
Release Program mode : Press two Stick Switch
simultaneously for a second.
Indication of Program mode : Red Led will be blinked
once per a second interval
.
Program mode : Blink once per a second interval
(2) Saving Data
50pcs of last used Data could be saved.
(3) Adjustment of Servo End Position
In case of Stick Calibration, Default will be 100%. At this
value, Customer can adjust trim as below way.
- 100% --> 1100us ~ 1900us
At Max. or Min. Position of Stick, adjust Trim Switch
Range of Trim is available 0% ~ 100% ~ 150%.
If move to 100% position, High Beep sound will be
occurred once.
- Red Led will be blinked once per a second interval
Program mode : Blink once per a second interval
(4) Servo Reverse Set
This is used when change Servo direction.
All sticks are on neutral position, and move the trim
switch to Max. or Min. Position.
If press Power switch with pressed trim switch to Max. or
Min. position, Normal mode and Reverse mode will be
changed.
- Indication of Servo Receiver mode : Red Led will be
blinked once per a second interval
- Normal mode : Green LED will be blinked once per a
second interval.

P5
-Reverse mode : Green LED will be blinked twice per a
second interval.
Program mode : Blink once per a second interval
Normal mode : Blink once per a second interval
(Repetition 5times)
Reverse mode : Blink twice per a second interval
(Repetition 5times)
(5) Fail Safe Set
Press right stick switch for a second at Program mode.
Press trim button per channels and select Fail pos mode
and Hold it.
Whenever press Trim button, Setting-condition will be
transferred to Receiver.
If press right-stick switch for a second, Fail safe setting
mode will be ended.
- Indication of Fail Safe mode : RED LED will be blinked
twice per a second interval.
- Pos mode : If Trim is UP, it is a Fail safe mode, and
Green LED will be blinked twice per a second interval.
(Repetition 5times)
- Hold mode : If Trim is Down, it is a Hold mode, and
Green LED will be blinked once per a second interval.
(Repetition 5times)
Program mode (Failsafe mode): Blink twice per a
second interval
Hold mode : Blink once per a second interval (Repetition
5times)
Pos mode : Blink twice per a second interval (Repetition
5times)
How to do Stick Calibration
(1) Enter to Stick Calibration Mode
Turn On the Radio, in state of pressing left stick switch.
If enter to Mode, RED LED will blink 3 times.
Stick calibration mode : Blink 3 times per a second
interval
(2) Set Stick Calibration
Move all sticks from side to Side and back to middle
position.
After operated last stick, hold it to middle position for
3Seconds.
If Set is done, Red and Green LED will blink 3Times at
same time.
Stick calibration mode Stick move done
Blink 3 Times per a second interval
※after that, it is moved to Dead Range set mode
automatically.
(3) Dead range set
This is for keep Neutral position, in case of they have no
accurate Neutral value.
Dead range set about Neutral position, is set by trim
switch up and down.
It can be settable from 1 to 6 steps. ( 0, 2, 4, 6, 8, 10% )
※in case of Throttle CH1, there is no spring, Do not set.
( only set for CH2, CH3, CH4 )
Green LED will blink depends on Neutral set steps.
For example, if you set Dead range to 6%, LED will
blink 4times per a second interval.
Dead range mode
Blink 3times per a sec interval.
Dead range set
Blinks depends of setting value (6 steps)
If set is done, press left stick button for 2 sec.

P6
안전규격
(1) KC 인증
Graupner mz-8 Transmitter
KCC인증번호: MSIP-CRM-sjr-16006700
(2) Conformite Europeenne
Product(s): Graupner mz-8 Transmitter,
(3) FCC Information
Graupner mz-8 Transmitter
FCC ID: SNL-16006700
FCC Statement
1. This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party
responsible for compliance could void the user‘s authority to operate
the equipment.
•NOTE
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- _Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
•
◎ Notes on environmental protection
This symbol on the product, user
manual or packaging indicates that this
product must not be disposed of with
other household waste at the end of its
life. It must be handed over
to the applicable collection point for the
recycling of electrical and electronic
equipment.
The materials are recyclable as marked. By recycling,
material reusing or other forms of scrap usage you are
making an important contribution to environmental
protection.
Batteries and accumulators must be removed from the
device and disposed of at an appropriate collection point.
Please inquire if necessary from the local authority for
the appropriate disposal site.