Green Bike City Premium 2020 User manual

MODEL HF 202–48N City Premium 2020
Customer Service:
Green Bike –Electric Motion LLC.
Main Office: 7059 Reseda Blvd, Reseda CA 91335
Phone: [phone]
Email: [email protected]om
Website: GreenBikeElectric.com

Instruction Manual
Green Bike –Electric Motion Congratulate you on your newly purchased!
Joining Greenbike’s Go Green revolution will open your doors to a whole new world of freedom!
Green Bike –Electric Motion gives your money the value it deserve, friendly and professional service and
safety for the rider above all.
Please maintain the product-customer-importer relationship to guarantee a quality experience for the long
term. In this manual you will find all the details required to care and maintain your product.
To ensure safety during riding and to maintain long-term usage experience, please read all instructions
carefully and follow the specified maintenance and usage instructions before using the bike.
Thank you for choosing Green Bike –Electric Motion!

Approved by CPSC
American Standards (CPSC - 16CFR1512) and is intended for urban cycling.
- Do not allow an additional rider on the bike. This bike is designed to carry one person only.
Any damage to the bicycle resulting from an additional rider is not covered under warranty.
- The height of the seat and handlebars should be adjusted for maximum comfort and control.
- The seat post and handlebars have a safety strip, be sure it is not visible when adjusting. If the strip is not
set correctly, excess pressure will be created and will damage the cables.
1-Brake Handles. 2-Grips. 3-Handlebars. 4-Adjustable Stem. 5-Display. 6-Gear Shifter. 7-Front
Brake Cable. 8-Rear Brake Cable. 9-Head light and horn. 10-Front Light. 11-Fender. 12-Tire and
Inner tube. 13-Front Wheel. 14-Frame. 15-Front fork. 16-Front wheel gear (Crank). 17-Chain shield
18-Pedal assist sensor. 19-Shock absorber for seat. 20-Seat Clamp. 21-Lithium battery. 22-Motor
Controller. 23-Pedal. 24-Rear Rack. 25-Rear Light. 26-Rear Brake. 27-Rear Fender. 28-Derailleur.
29-Mechanism protection. 30-Gears. 31-Motor. 32-Seat.

- Be sure that the hinge locks of the seat and handlebars are locked before starting the trip.
- Check the condition of the brakes frequently and adjust when necessary. Braking range on a dry road is
13 feet and on a wet road can reach 50 feet. Keep more distance on a wet road.
- The chain is properly adjusted and should not be altered. The chain must be lubricated to prevent
accelerated weathering.
- At night, the headlight and backlight must be switched on by a switch on the control display.
- Be sure to wear appropriate clothing and do not carry objects or bags in a way that they can be caught in
the wheels or chain. To keep the rider safe - do not bring your legs to close to the chain.
- Do not ride in weather that does not allow safe riding such as rain, puddles, strong winds, snow, etc.
- When stopping, use both brakes. Don’t settle with one brake, Use both brakes together in order to
maintain stability and achieve greater control.
- Do not ride under the influence of alcohol, drugs or substances that affect the rider's alertness.
- When riding, you must hold both handles, do not perform stunts and reckless turns without examining
the area from all sides before proceeding.
- Please follow local and state regulations.
- Do not drop the bike on the ground (due to the sensitivity of the battery, motor and controller). The bike
should be placed on the kickstand carefully.
- Do not jump or climb sidewalks on the road.
- Damage to either the spokes, wheel, or tires resulting from typical cycling injuries and accelerated wear
of the battery (which may result from travel with a curved wheel) are not covered by the warranty.
Folding the Bike
- The bike can be folded for storage at home or in the trunk of the car.
- The folding time is only 10 seconds. You can get a demonstration at the point of purchase or watch a
tutorial video on our site www.GreenBikeElectric.com
Here are the pictures of the bike in a folded position and in an average car trunk:

Before You Start to Ride
Raise the seat as shown in Figure 3 and insert the battery into place and lock it.
Picture 3 Picture 4

LCD-S900 E-bike Intelligent Display manual
1.Overview of S900
1) UART protocol:
Equipped with independent press buttons
2) Speed：
Real-time SPEED，MAX SPEED，Average SPEED
Kmh/mile：
Kmh/MPH according to habit
3) Battery level：
Indicates the battery level in real time
4) Head light control：
Press button to power on/off
5) Back light adjustment：
3-level adjustment
6) Assist level：
From 0 to 5, press button to change assist level, 0-no assist, 5-default value
7) Distance：
ODO/Trip/Driving duration
8) Error code：
Please refer to appendix table 1 for definition
9) 6km mode：
In this mode, it will display “WALK” on the screen
10) Parameter setting：
Set parameters, such as: wheel size, speed limit etc.
2.Presentation of screen

1) Speed：Average SPEED/MAX SPEED/Real-time SPEED
2) Speed unit：Kmh/MPH
3) Battery level: 5 levels, voltage interval could be customized
4) Head light icon indicates when head light and back light are on
5) Error code：“ERROR” and code when there is error
6) Assist level actual assist level 0~5, 0 –no assist, 1- ECO, 2,3-STD，4,5-POWER)
7) Distance Trip/ODO
8) 6km mode
3. Press button definition
LCD-S900 uses independent press button, in total three buttons:
“UP”、“MODE”、“DOWN”。
4.Operation instructions
1) Power ON/OFF
When the power is off, Long press （MODE during 3 seconds screen will display all contents
and start to normal working mode, and controller will be turned on

When the power is on, Long press （MODE during 3 seconds screen will be powered
offhand controller will be turned off。If no any operation both on bike and display during 10 minutes
(time could be set), the display will turn off automatically, in this case, no power consumption for
both display and controller
Figure 1
2) ODO/TRIP
Short press to switch ODO/TRIP，Trip (Single trip distance) →ODO (Accumulated distance)
Figure 2 Figure 3
3) Assist level
Short press or to change assist level default value is level

4) Different Speed display:
Long press and to switch different speed information, real time speed (SPEED）
→ Max speed (MAX SPEED）→Average speed (AVGSPEED）→Driving Time。

5) Head light control
Long press ，turn on/off the head light。
6) 6km mode
When the bike is stopped, long press , will enter 6km/h mode, the speed will be
4.5~7.5km/h according to different road conditions, “WALK” will show up on screen, long press again
or short press ,will quit 6km/h mode. Long press or short press could be
customized by clients.

5. Parameter setting
When the display is powered on long press and ，will enter parameter setting mode
(Figure 13), in this mode, can change parameter values long press again and will quit
parameter setting mode or no operation during 10s will also quit this mode
In parameter setting mode short press / will change parameter value short press
will save current value and switch to next parameter
1) P01-back light lightness：
Short press / will switch from 1 to 3, Level 3 is lightest. Level 2 is default value.
2) P02-kmh/MPH:

Short press / to Switch Kmh/MPH
3) P03-Working voltage:
Short press / to switch 24V, 36V, 48V, Default value is 36V
4)P04-Auto shutdown time:
Short press / to switch from 0 to 60, it is the time(in minutes) to shut down the
screen automatically if no operation 0 means never shut down, Default value is 10 minutes
5)P05-Number of Assist levels:

Short press / to change level 0->1->2
0：3 assist levels
1：5 assist levels
2：9 assist levels
6)P06-Wheel size selection:
Short press / to switch wheel size in inch，step：0.1 inch
7)P07-Number of magnets for speed sensor:
Short press / to switch from 1 to 100

8)P09-Non-zero speed start:
Short press / to switch from0 to 1. 0：zero speed start, 1:non-zero speed start
9)P10-Driving mode selection:
Short press / to switch from 0->1->2
0：Assist mode (throttle does not work, only assist) ；
1：Electrical driving mode (only throttle works, assist does not work)
2：Both assist and Electrical driving mode (Not available if in zero speed start and electrical driving
mode)

10) P11-assist sensitivity setting:
Short press / to switch from 1 to 24
11) P12-assist starting power setting:
Short press / to switch from 0 to 5:

12) P13-Assist magnetic disc types:
Short press / to switch from 5->8->12，different numbers of magnets
13) P14-Current limit for the controller:
Short press / to switch from 1 to 20A
14) P15-low voltage protection for controller:
Figure 29

15) P16-Reset ODO distance:
Long press during 5 seconds
16) P18-Reset all parameters:
Long press 5 seconds when it displays “SSSS”，all parameters reset to default values
(except for the ODO distance)
6.Specifications
1) Power supply: 24V,36V,48V
2) Rated current: 10mA
3) Max current: 30mA
4) Leakage current after power off: <1uA
5) Current supply to controller:50mA
6) Working Temperature：-18~65℃
7) Storage temperature：-30~80℃

7.Error code definition
When an error appears, S900 will notice users by different codes, please refer to Table 1 for different
codes:
Code
(Decimal)
Signification
0
Normal
6
Low Battery level
7
Motor error
8
Throttle error
9
Controller error
10
UART receive error
11
UART receive error
Table 1
8.Notices
Power on and power off must keep an interval of at least 3 seconds, please don’t press “MODE”
button frequently when it is powered off.
When the temperature is under -10℃, the screen will be a little darker than normal, when the
temperature increases, the screen can go back to normal.

The Electrical System is Now Ready!
• Fold the kickstand from the ground, then sit on the seat. Put one foot on the pedal and the other on the
ground.
• Now, start pedaling and the engine will go into action. There will be a faint rustle of the pass-through.
• To maintain battery life, do not use it until its end. When the battery meter flashes, turn off the power
switch and use the pedal as a regular bicycle. After recharging, you can ride again with the electric motor.
• Back Injury: The rear of the bike is not intended to carry people. Maximum load is up to 25 kg, and the
luggage should be tied with straps and tested during riding.
• Park in a safe place that is not an obstacle to vehicles or pedestrians. Place the bike on the kickstand,
disconnect the power with the main switch and pull the key out of the lock.
• The bike must be locked with a massive lock that make it difficult to steal. It is recommended to take the
battery with you.
• Charging: The battery must be charged only with the charger that supplied with the bike. A lithium
battery is only charged by a charger that designated to lithium batteries and not by other charger. The
battery must be charged with GUANZHOU ELECTRONICS CORPRATION P / N; S12.
Charging with a different charger can damage and void battery warranty.
Do not open the battery or charger for testing or repair! Bring to repair shop for testing!
• Charging takes up to 6 hours, depending on battery status. The battery can be charged both on and off
the bike.
• The charging cable must first be connected to the battery and then to the mains socket.
• When the charge indicator light is red, the battery is charging. When the charge light turns green, the
battery is full and must be disconnected from the power source. When charging, the battery must be in a
proper position so the battery won’t fall or be damaged.
• The charger becomes hot during charging. Keep it away from any flammable materials and keep the
vents unblocked
• Be sure to properly dispose of dead batteries at proper recycling plants and do not throw away in the
trash.
• Before beginning the ride, check that all the indicator lights are working and the battery is locked in
place.
• Check that the electrical contacts of the battery are always clean. Clean with a dry cloth without
moisture.
• Check tire pressure regularly (40 PSI). Poor pressure will cause overuse of the battery and shorten cycling
time.