Green GPM-303 User manual

Display Six digits, 0.4 Inch seven segment LED
User programming 3 Keys & Display
One relay, 1 c/o
Output
Relay contact rating 10 A @ 230 VAC
(Resistive load) / 30 VDC
Power consumption 4.8 VA
Reset : Auto / Manual Auto reset Time 000.1 Sec to 999.9 Sec
Range 999 999 Counts
Count direction Up
SPECIFICATIONS
Supply voltage 230 VAC
Weight 170 grams
Dimension (L x W x D) 96 x 48 x 75
Mechanical life of relay
Electrical life of relay
Ambient temperature
Ambient humidity 35 to 85 % RH
Storage temperature
10 million operation
100000 operation
-10 to 55 c
-25 to 65 c
Operating voltage range + / -10% from the rated voltage
In the pack counter, side clamp and instruction manual
Input NPN (or) PNP Proximity unit (Selectable)
Pulse frequency Low : Less than 30 Hz & High : More than 30 Hz
Special feature Memory Retension
Indications Input Pulse and Relay ON
Set points Two (Count and auto reset time)
GPM - 303
All dimensions are in mm
90
45
75
10
INTRODUCTION
WIRING DIAGRAM
PANEL CUTOUT DIMENSION
MANUFACTURER
PRECAUTION FOR SAFE USE
NOTE:
F
DIMENSIONS
1. Our company shall not be liable for any damages, as described
below, caused to both any users and third parties
a) Damages caused by the result of operation of the product.
b) Damages caused by any defects in the product which are
unpredictable for us.
2. The content in this manual are subject to change without any
notice. If you have any suggestion on the matter,
Please do not hesitate to contact us.
(4) Separate the input signal devices, input signal cables
and the product from the source
of noise or high - tension
cables producing noise
(5) The supplied power voltage and load must be within the
rated and specified ranges.
(6) Do not use where the water or oil splatter on the Timer
(7) Install a switch or circuit breaker that allows the operator
to immediately turn off the power
(1) Use and store the Timer within the specified
ambient temperature and humidity ranges.
(2) Do not use the product in location subject to vibrations
or shocks. Using the product in such location over a long
period may result in damage due to stress.
(3) Do not use the product in locations subject to dust,
corrosive gases, or direct sunlight
Thank you very much for purchasing this GREEN product
GPM-303. Please read the instruction manual carefully for
the full usage of this product
The has passed various quality tests before despatch.COUNTER
Please check however, at the time of arrival, its model code
and its appearance and ensure that all the contents are provided
and there are no faults, damage etc, to the timer. Please also
ensure that the model code ,which is labeled on the timer,
is identical to the one you ordered.
48
96
GPM - 303 PROGRAMMABLE COUNTER
GREEN
SET
I / P PULSE RELAY
GREEN MICROELECTRONICS INDIA PVT. LTD.
green@green .inelectronics www.greenelectronics.in 0422-2590288
PROGRAMMABLE COUNTER
V1.2
1
9
234
10
5
11 12 13
678
14 16
SENSOR MANUAL
RESET
O / P
15
12
LED
GREEN
NPN / PNP
PROXIMITY
+
-
E PN
24 VDC
OUTPUT 100 - 240 VAC, 50HZ
SUPPLY
RELAY
NO
C
NC

SET
Press PARAMETER SELECTION
before Power ON for
OPERATION PROCEDURE :
>
Press
LED BLINKS
Blinking display
increments
Returns after 1Sec.
and release
Press for 3sec
Press SET
Power ON
to shift blinking
position
SET
Relay and Count is reset
Counting Up count
COUNTING =
SET VALUE
Pulse input
No
Yes
(Relay ON)
Reset Type
If
No
Yes
Relay Reset
after Output Time
See Note
Press SET
OPERATION LEVEL
OR
Scaled value will displayed in PV display. Actual value will displayed in PV display.
>
This can be changed by pressing in Operation level
Press
>
PV DISPLAY
SET VALUE SELECTION
SET POINT DISPLAY
Count and relay can be reset in
the following ways and the offset
value will automatically loaded
1.By giving external
reset signal
2.By pressing Set key
for 3Sec in operation
level.(Display enters
set value selection
screen)
NOTE:
F
OPERATION LEVEL
Press
>
If
Press
>
(or)
Choose Relay Reset type
(or)
Press
>
Press
>
Press
>
Press
>
Press SET
Press SET
Press SET
Press
>
If
Press
>
Press
>
Press SET
Press SET
Press SET
PARAMETER SELECTION
HIGH LOW
PNP NPN
AUTO MANUAL
Auto : As soon as count reaches Set Value,the present value display
returns to the reset status.
The output is held ON until Output Time is complete
Manual : The present value continues to increment
and the output is held ON until reset.
OPERATION AFTER COUNT COMPLETION
Input
Frequency
Input
Input
Input
Reset
Input
Output Time
Scaling
Offset
Decimal
Press
>
Press
>
DECIMAL POSITION
Selected the decimal point position
is shown in the PV display
F
Press
>
Press
>
Press
>
>
Press
>
After reset this value will load
VALUE SETTING SIGN SETTING
>
Press Press
>
VALUE SETTING
NOTE: Count X Scale = PV
Press
>
DECIMAL SETTING
Choose for input
frequency < 30 Hz
Choose for input
frequency < 5 KHz
(or)
Choose for
PNP type sensor
Choose for
NPN type sensor
HOLD RESET
Press
>
Set Value : 2000 counts
Output Time : 10Sec
Relay turns ON when 2000 counts is reached.
After 10Sec relay turns OFF
EXAMPLE:
F
(or)
Choose for resetting output time and
relay status during power failure
F
IF AUTO RESET MODE IS SET
Choose for output time and relay status
retention during power failure.
Sec
>
>
Set the time using and
Timer Memory
Press
>
Press SET
Press SET
Press
>