Greenfields Outdoor Fitness GR2005-1-22 User manual

2x4s: approximately four, 8’ to 10’ lengths per unit.
All-Thread: 3/8” to 1/2”, cut in 1’ lengths, two pieces per
embedded pipe.
Nuts & Washers: to fit all-thread, four sets per embedded pipe.
Stakes: metal/wood, approximately six per unit.
Pavers/Cinder Blocks: 1 to 2 per unit.
Tie Wire/C-Clamps
Duplex Wood Nails/Dry Wall Screws
Concrete: 3250 psi or better.
Tools: cordless impact driver, skill saw, pliers, hammer, small
sledge, magnetic level, tape measure, shovels, wheelbarrows,
etc.
Plans/Drawings: schematic drawings and instructions for each
model # to be installed.
The following information for contractors, maintenance personnel and supervisory staff will help
ensure an accurate, safe and problem-free installation.
SUGGESTED MATERIALS
Area should be fenced—recommend 6’
temporary fencing, entire perimeter.
Ground should be thoroughly graded and
“finished grade” accurately established, using
either laser or string-line methods.
Prior to digging, entire site should be “laid-out”
with all footings clearly marked as per plans.
In the U.S. contact “Dig Alert” for clearance to
dig, and follow all local construction regulations
(fencing, dirt removal, etc.)
Dig footings, closely following given dimensions.
Remove dirt and debris from site, prior to
placing units.
SITE PREP - Before equipment handling
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
1.
2.
3.
4.
5.
6.
Preliminary Instructions:
In-Ground Embedded Footings
Please be advised that the use of decomposed granite surfacing
(DG) is known to accelerate normal wear & tear of footrests.

All units must be fully assembled before installation
All screws must be attached using LocTite
Do not drag units along the ground
If missing parts or damaged items are noticed during
installation, or should any assistance be required, please
contact Greenfields immediately at 888-315-9037 x105.
Brace units at the designated locations using the 2x4s,
secured by c-clamps, all-thread or tie-wire. Use padding to
avoid scratching powder coating.
Suggested safety zone is about 48” - 60” preimeters around
usage area (seats and moving parts). Clearance area may
overlap with a nearby unit, as long as there is enough
clearance to safely mount and dismount each unit.
Make sure all units are plumb and leveled
Adhere to surfacing level (marked on units with blue tape)
Pour concrete
Clear concrete residue from post and other parts
Let concrete dry. It is recommended to wait a minimum of one week after concrete is poured before
equipment is used.
Remove supports
Touch up units using attached guide
Wrap units in black tarps until open to public
At the end of installation, toolbox and all documentation should be submitted to the local
maintenance staff.
ma
ma
ma
ma
a
in
in
in
in
te
te
te
te
te
na
na
na
na
na
nc
nc
nc
e
e
e
st
st
st
a
af
a
af
a
af
f
f
f
f
f
f.
f
f.
BASIC INSTALLATION GUIDELINES
UNITS ARE HEAVY (up to 450 lbs.) When unloading and
handling, please exercise extra care to prevent injury or
damage to the equipment.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Preliminary Instructions:
In-Ground Embedded Footings

If installaon is not taking place immediately,
designate a safe area to store crates.
Check each container label immediately with the
shipping company’s bill of lading to ensure that every
item is present. Use the delivery receipt to record any
missing items.
RECEIVING YOUR EQUIPMENT
Units must be carefully unloaded to ensure
safety of the installers as well as the
equipment itself. Units are heavy and bulky
and will require 2 - 4 people to handle. Make
sure a forkliwith long forks is available.
All units have been inspected before final
packing; however, please review the packing
slip to ensure that all pieces are present. If
anything is missing, call 888-315-9037 x105
immediately. Save all paperwork for future
reference.
INSTRUCTIONS & TIPS FROM
GREENFIELDS OUTDOOR FITNESS
delivery
unloading
Thank you for purchasing a high-quality gym from
Greenfields Outdoor Fitness! You have taken an
important step to improve the health and well-being
of your community.

RECEIVING YOUR EQUIPMENT
Use 2x4 beams to posion units, secured by either
c-clamps or all-thread as shown.
Touch-up paint is provided in the enclosed
toolbox. If missing parts or damaged items
are noced during installaon, or should any
assistance be required, please contact Greenfields
immediately at 888-315-9037 x105.
At the end of installaon, toolbox and all
documentaon should be submied to the local
maintenance staff.
installation

INSTALLATION INSTRUCTIONS
Model:
Name:
During installation, please be sure to also refer to guidelines in Greenelds’ Preliminary Instructions document.
© 2015 Greenelds Outdoor Fitness, Inc.
In order to honor our commitment to quality and safety, Greenelds Outdoor Fitness reserves the right to make changes and revise the design specications without notice.
Questions? Please call
888-315-9037 x105
Dimensions
Greenelds installation instructions:
1. All units MUST be fully assembled,
leveled, and braced in place in the foot-
ing hole before any concrete is poured.
2. A monolithic pour MUST be used for
concrete. (All concrete must be poured
at one time)
3. Concrete requirement: 3250 psi or better.
4. The top of the blue tape attached to the posts on the
equipment is nal top surface level.
5. All screws must be attached using LocTite.
6. It is recommended to wait a minimum of one week
after concrete is poured before equipment is used.
7. The use of Decomposed Granite Surfacing (DG) is known
to accelerate normal wear & tear of footrests.
GR2005-1-22
Pendulum, Abs, & Dip station
This unit ships in 2 separately wrapped components.
2434"
24"
24" 20"
40"
Surface Level
Optional
Surfacing
24"
Ensure distance
between handle-
bars is equal on
both sides.
_
_
Tighten Screws fully
inside backrest and
on main post.
Finished productFinished product

INSTALLATION INSTRUCTIONS
Model:
Name:
© 2015 Greenelds Outdoor Fitness, Inc.
1. Clamp the two center pipes
between two 2X4s, using all-thread, nuts
and washers.
2. Top of boards should be even with
the “nished grade” markings on pipes,
usually done with blue tape.
3. Stand unit in the prepared footing;
use laser or string-line to measure height
of unit.
4. Raise/lower unit so that “nished
grade” marking on pipes is correct height.
Pieces of cinder block may be placed
directly under the pipes and/or wooden
blocks and shims may be placed under
the clamping 2X4s.
5. Stake the clamping 2X4s to the
ground on each side of the unit.
6. With magnetic level, make sure
both pipes are plumb. Then attach a
balancing 2X4 (kicker) to the top portion
of the unit with tie wire and stake the
other end to the ground. If needed for
stability, a second 2X4 may be attached
and staked in a different direction.
7. Place metal pegs/rebar through
prepared holes in embedded pipe.
8. Pour concrete into footings. Use
vibration or thorough shovel mixing to ensure
a good set around embedded pipes, and to
eliminate air pockets.
9. Depending on the type of surface to be
installed, there should be approximately 4”
between the top of the concrete and “nished
grade.”
GR2005-1-22
Pendulum, Abs, & Dip station
GR2005-1-22
Pendulum, Abs, & Dip station

INSTALLATION INSTRUCTIONS
Model:
Name:
During installation, please be sure to also refer to guidelines in Greenelds’ Preliminary Instructions document.
© 2015 Greenelds Outdoor Fitness, Inc.
In order to honor our commitment to quality and safety, Greenelds Outdoor Fitness reserves the right to make changes and revise the design specications without notice.
Questions? Please call
888-315-9037 x105
Dimensions
Greenelds installation instructions:
1. All units MUST be fully assembled,
leveled, and braced in place in the foot-
ing hole before any concrete is poured.
2. A monolithic pour MUST be used for
concrete. (All concrete must be poured
at one time)
3. Concrete requirement: 3250 psi or better.
4. The top of the blue tape attached to the posts on the
equipment is nal top surface level.
5. All screws must be attached using LocTite.
6. It is recommended to wait a minimum of one week
after concrete is poured before equipment is used.
7. The use of Decomposed Granite Surfacing (DG) is known
to accelerate normal wear & tear of footrests.
GR2005-1-26
2-Person Cross Country Ski
This unit ships in 2 separately wrapped components.
24"
24"
24"
Optional
Surfacing
Surface
Level
24"
24"
41"
32"
Ø24"
24"
32"
Greenfields
41"
16"
16"
16"
18"
Distance
between
pedals must
be equal on
both sides of
the unit.
height of pedals
from surface
grade must be
equal on both
sides
Usage and
safety Sign
24"
Sign must face away from unit
24"
Finished productFinished product

INSTALLATION INSTRUCTIONS
Model:
Name:
© 2015 Greenelds Outdoor Fitness, Inc.
1. Stand assembled unit in the four
prepared footings.
2. Slide two 2X4s (approximately 6’long)
under the support bars located on both
sides of the unit. There should be about 2’
extending on each side.
3. Use laser or string-line to measure
height of unit.
4. Raise/lower unit so that “nished
grade” markings on the four legs (done
with blue tape) are correct height. Pieces
of cinder block may be placed directly
under the legs and/or wooden blocks and
shims may be placed under the extending
2X4s.
GR2005-1-26
2-Person Cross Country Ski
5. Use magnetic level to check that both sides
are plumb.
6. Place metal pegs/rebar through prepared
holes in embedded pipe.
7. Pour concrete into footings. Use vibration
or thorough shovel mixing to ensure a good
set around embedded pipe, and to eliminate
air pockets.
8. Depending on the type of surface to be
installed, there should be approximately 4”
between the top of the concrete and “nished
grade.”

INSTALLATION INSTRUCTIONS
Model:
Name:
During installation, please be sure to also refer to guidelines in Greenelds’ Preliminary Instructions document.
© 2015 Greenelds Outdoor Fitness, Inc.
In order to honor our commitment to quality and safety, Greenelds Outdoor Fitness reserves the right to make changes and revise the design specications without notice.
Questions? Please call
888-315-9037 x105
Dimensions
Greenelds installation instructions:
1. All units MUST be fully assembled,
leveled, and braced in place in the foot-
ing hole before any concrete is poured.
2. A monolithic pour MUST be used for
concrete. (All concrete must be poured
at one time)
3. Concrete requirement: 3250 psi or better.
4. The top of the blue tape attached to the posts on the
equipment is nal top surface level.
5. All screws must be attached using LocTite.
6. It is recommended to wait a minimum of one week
after concrete is poured before equipment is used.
7. The use of Decomposed Granite Surfacing (DG) is known
to accelerate normal wear & tear of footrests.
GR2005-1-47-W
2-Person Accessible Vertical Press
This unit ships in 1 separately wrapped component.
24"
Surface
Level
Optional
Surfacing
24"
24"
10"
Stopper Plate
must rest above
final surface level
24"
65"
38"
Finished product
U.S. Pat. No. 9,079,069 B1
Finished product

INSTALLATION INSTRUCTIONS
Model:
Name:
© 2015 Greenelds Outdoor Fitness, Inc.
1. Clamp center pipe between two 2X4s,
using all-thread, nuts and washers.
Top of boards should be even with the
“nished grade” marking on pipe, usually
done with blue tape.
2. Cut two 2X4 blocks at 5”, this should
be the distance between the “nished
grade” marking and the rst chair support
welded to the center pipe. Wedge one
5” block between the clamping 2X4s
and the welded support--do this on both
sides. These blocks keep this heavy unit
from sliding between the clamping 2X4s.
3. Stand unit in the prepared footing; use
laser or string-line to measure height of
unit.
4. Raise/lower unit so that “nished
grade” marking on center pipe is correct
height. Pieces of cinder block may be
placed directly under center pipe and/or
wooden blocks and shims may be placed
under the clamping 2X4s.
5. Stake the clamping 2X4s to the
ground on each side of the unit.
6. With magnetic level, make sure
that the center pipe is exactly plumb.
Then attach a balancing 2X4 (kicker) to
the top portion of the unit with tie wire
and stake the other end to the ground.
GR2005-1-47-W
2-Person Accessible Vertical Press
If needed for stability, a second 2X4 may be
attached and staked in a different direction.
7. Metal stoppers should be wired in
place, directly under both the seat and the
wheelchair weight.
8. Arms must be held at exact angle for
correct operation. On the chair side, place a
10” temporary spacer between the hand grip
and the edge of the back rest.
9. Arm on wheelchair side needs to be at
same angle, so that bar attached to weight is
parallel to the ground. Use 2X4 to prop arm
temporarily.
10. Place metal pegs/rebar through prepared
holes in embedded pipe and stoppers.
11. Pour concrete into footings. Use vibration
or thorough shovel mixing to ensure a good
set around embedded pipe, and to eliminate
air pockets.
12. Depending on the type of surface to be
installed, there should be approximately 4”
between the top of the concrete and “nished
grade.”
U.S. Pat. No. 9,079,069 B1

INSTALLATION INSTRUCTIONS
Model:
Name:
During installation, please be sure to also refer to guidelines in Greenelds’ Preliminary Instructions document.
© 2015 Greenelds Outdoor Fitness, Inc.
In order to honor our commitment to quality and safety, Greenelds Outdoor Fitness reserves the right to make changes and revise the design specications without notice.
Questions? Please call
888-315-9037 x105
Dimensions
Greenelds installation instructions:
1. All units MUST be fully assembled,
leveled, and braced in place in the foot-
ing hole before any concrete is poured.
2. A monolithic pour MUST be used for
concrete. (All concrete must be poured
at one time)
3. Concrete requirement: 3250 psi or better.
4. The top of the blue tape attached to the posts on the
equipment is nal top surface level.
5. All screws must be attached using LocTite.
6. It is recommended to wait a minimum of one week
after concrete is poured before equipment is used.
7. The use of Decomposed Granite Surfacing (DG) is known
to accelerate normal wear & tear of footrests.
GR2005-1-48A-W
2-Person Accessible Chest Press
This unit ships in 1 separately wrapped component.
Stopper Placement
Below Seat
24"
24"
Surface Level
Optional
Surfacing
Min Gap 12"
24"
24"
Use 7"
long 2x4
for proper
spacing Stopper Plate
must rest above
final surface level
65"
Finished product
U.S. Pat. No. 9,079,069 B1

INSTALLATION INSTRUCTIONS
Model:
Name:
© 2015 Greenelds Outdoor Fitness, Inc.
1. Clamp center pipe between two 2X4s,
using all-thread, nuts and washers.
2. Top of boards should be even with the
“nished grade” marking on pipe, usually
done with blue tape.
3. Cut two 2X4 blocks at 5”, this should
be the distance between the “nished
grade” marking and the rst chair support
welded to the center pipe.
Wedge one 5” block between the
clamping 2X4s and the welded support--
do this on both sides. These blocks keep
this heavy unit from sliding between the
clamping 2X4s.
4. Stand unit in the prepared footing; use
laser or string-line to measure height of
unit.
5. Raise/lower unit so that “nished
grade” marking on center pipe is correct
height. Pieces of cinder block may be
placed directly under center pipe and/or
wooden blocks and shims may be placed
under the clamping 2X4s.
6. Stake the clamping 2X4s to the
ground on each side of the unit.
7. With magnetic level, make sure
that the center pipe is exactly plumb.
Then attach a balancing 2X4 (kicker) to
GR2005-1-48A-W
2-Person Accessible Chest Press
the top portion of the unit with tie wire and
stake the other end to the ground. If needed
for stability, a second 2X4 may be attached
and staked in a different direction.
8. Metal stoppers should be wired in
place, directly under both the seat and the
wheelchair weight.
9. Arms must be held at exact angle for
correct operation. On the chair side, place a
10” temporary spacer between the hand grip
and the edge of the back rest.
10. Arm on wheelchair side needs to be at
same angle, so that bar attached to weight is
parallel to the ground. Use 2X4 to prop arm
temporarily.
11. Place metal pegs/rebar through prepared
holes in embedded pipe and stoppers.
12. Pour concrete into footings. Use vibration
or thorough shovel mixing to ensure a good
set around embedded pipe, and to eliminate
air pockets.
13. Depending on the type of surface to be
installed, there should be approximately 4”
between the top of the concrete and “nished
grade.”
U.S. Pat. No. 9,079,069 B1

INSTALLATION INSTRUCTIONS
Model:
Name:
During installation, please be sure to also refer to guidelines in Greenelds’ Preliminary Instructions document.
© 2015 Greenelds Outdoor Fitness, Inc.
In order to honor our commitment to quality and safety, Greenelds Outdoor Fitness reserves the right to make changes and revise the design specications without notice.
Questions? Please call
888-315-9037 x105
Dimensions
Greenelds installation instructions:
1. All units MUST be fully assembled,
leveled, and braced in place in the foot-
ing hole before any concrete is poured.
2. A monolithic pour MUST be used for
concrete. (All concrete must be poured
at one time)
3. Concrete requirement: 3250 psi or better.
4. The top of the blue tape attached to the posts on the
equipment is nal top surface level.
5. All screws must be attached using LocTite.
6. It is recommended to wait a minimum of one week
after concrete is poured before equipment is used.
7. The use of Decomposed Granite Surfacing (DG) is known
to accelerate normal wear & tear of footrests.
GR2005-1-48-W
2-Person Accessible Lat Pull
Stopper Placement
Below Seat
24"
24"
Surface Level
Optional
Surfacing
24"
Arms should be level
Stopper Plate
must rest above
final surface level
Use rope to hold
seat and arms
at correct
position
65"
24"
65"
Finished product
U.S. Pat. No. 9,079,069 B1
This unit ships in 1 separately wrapped component.

INSTALLATION INSTRUCTIONS
Model:
Name:
© 2015 Greenelds Outdoor Fitness, Inc.
1. Clamp center pipe between two 2X4s,
using all-thread, nuts and washers.
2. Top of boards should be even with the
“nished grade” marking on pipe, usually
done with blue tape.
3. Cut two 2X4 blocks at 5”, this should
be the distance between the “nished
grade” marking and the rst chair support
welded to the center pipe.
Wedge one 5” block between the
clamping 2X4s and the welded support--
do this on both sides. These blocks keep
this heavy unit from sliding between the
clamping 2X4s.
4. Stand unit in the prepared footing; use
laser or string-line to measure height of
unit.
5. Raise/lower unit so that “nished
grade” marking on center pipe is correct
height. Pieces of cinder block may be
placed directly under center pipe and/or
wooden blocks and shims may be placed
under the clamping 2X4s.
6. Stake the clamping 2X4s to the
ground on each side of the unit.
7. With magnetic level, make sure
that the center pipe is exactly plumb.
Then attach a balancing 2X4 (kicker) to
GR2005-1-48-W
2-Person Accessible
Lat Pull
the top portion of the unit with tie wire and
stake the other end to the ground. If needed
for stability, a second 2X4 may be attached
and staked in a different direction.
8. Metal stoppers should be wired in
place, directly under both the seat and the
wheelchair weight.
9. Arms must be held at exact angle for
correct operation. On the chair side, place a
10” temporary spacer between the hand grip
and the edge of the back rest.
10. Arm on wheelchair side needs to be at
same angle, so that bar attached to weight is
parallel to the ground. Use 2X4 to prop arm
temporarily.
11. Place metal pegs/rebar through prepared
holes in embedded pipe and stoppers.
12. Pour concrete into footings. Use vibration
or thorough shovel mixing to ensure a good
set around embedded pipe, and to eliminate
air pockets.
13. Depending on the type of surface to be
installed, there should be approximately 4”
between the top of the concrete and “nished
grade.”
U.S. Pat. No. 9,079,069 B1

INSTALLATION INSTRUCTIONS
Model:
Name:
During installation, please be sure to also refer to guidelines in Greenelds’ Preliminary Instructions document.
© 2015 Greenelds Outdoor Fitness, Inc.
In order to honor our commitment to quality and safety, Greenelds Outdoor Fitness reserves the right to make changes and revise the design specications without notice.
Questions? Please call
888-315-9037 x105
Dimensions
Greenelds installation instructions:
1. All units MUST be fully assembled,
leveled, and braced in place in the foot-
ing hole before any concrete is poured.
2. A monolithic pour MUST be used for
concrete. (All concrete must be poured
at one time)
3. Concrete requirement: 3250 psi or better.
4. The top of the blue tape attached to the posts on the
equipment is nal top surface level.
5. All screws must be attached using LocTite.
6. It is recommended to wait a minimum of one week
after concrete is poured before equipment is used.
7. The use of Decomposed Granite Surfacing (DG) is known
to accelerate normal wear & tear of footrests.
GR2005-1-71
3-Person Static Combo
This unit ships in 4 separately wrapped components.
24"
24"
24"
24"
20"
20" 20"
62"52"
Optional Top
Surfacing
Surface
Level
24"
24"
24" 20"
4" under
concrete
84"
Recommended Height
Finished product

INSTALLATION INSTRUCTIONS
Model:
Name:
© 2015 Greenelds Outdoor Fitness, Inc.
1. Clamp two pipes of assembled unit
between two 2X4s, using all-thread, nuts
and washers.
2. Top of boards should be even with
the “nished grade” markings on pipes,
usually done with blue tape.
3. Stand unit in the prepared footing;
use laser or string-line to measure height
of unit.
4. Raise/lower unit so that “nished
grade” marking on pipes is correct height.
Pieces of cinder block may be placed
directly under the pipes and/or wooden
blocks and shims may be placed under
the clamping 2X4s.
5. Stake the clamping 2X4s to the
ground on each side of the unit.
GR2005-1-71
3-Person Static Combo
6. With magnetic level, make sure
both pipes are plumb. Then attach a
balancing 2X4 (kicker) to the top portion
of the unit with tie wire and stake the
other end to the ground. If needed for
stability, a second 2X4 may be attached
and staked in a different direction.
7. Place metal pegs/rebar through
prepared holes in embedded pipe.
8. Pour concrete into footings. Use
vibration or thorough shovel mixing to ensure
a good set around embedded pipes, and to
eliminate air pockets.
9. Depending on the type of surface to be
installed, there should be approximately 4”
between the top of the concrete and “nished
grade.”

INSTALLATION INSTRUCTIONS
Model:
Name:
During installation, please be sure to also refer to guidelines in Greenelds’ Preliminary Instructions document.
© 2015 Greenelds Outdoor Fitness, Inc.
In order to honor our commitment to quality and safety, Greenelds Outdoor Fitness reserves the right to make changes and revise the design specications without notice.
Questions? Please call
888-315-9037 x105
Dimensions
Greenelds installation instructions:
1. All units MUST be fully assembled,
leveled, and braced in place in the foot-
ing hole before any concrete is poured.
2. A monolithic pour MUST be used for
concrete. (All concrete must be poured
at one time)
3. Concrete requirement: 3250 psi or better.
4. The top of the blue tape attached to the posts on the
equipment is nal top surface level.
5. All screws must be attached using LocTite.
6. It is recommended to wait a minimum of one week
after concrete is poured before equipment is used.
7. The use of Decomposed Granite Surfacing (DG) is known
to accelerate normal wear & tear of footrests.
GR2005-1-104
4-Person Leg Press
This unit ships in 3 separately wrapped components.
30"
36"
82"
36"
36"
Finished product

INSTALLATION INSTRUCTIONS
Model:
Name:
© 2015 Greenelds Outdoor Fitness, Inc.
1. Clamp center pipe between two
2X4s, using all-thread, nuts and washers.
2. Top of boards should be even with
the “nished grade” marking on pipe,
usually done with blue tape.
3. Stand unit in the prepared footing;
use laser or string-line to measure height
of unit.
4. Raise/lower unit so that “nished
grade” marking on center pipe is correct
height. Pieces of cinder block may be
placed directly under center pipe and/or
wooden blocks and shims may be placed
under the clamping 2X4s.
5. Stake the clamping 2X4s to the
ground on each side of the unit.
GR2005-1-104
4-Person Leg Press
6. With magnetic level, make sure
that the center pipe is exactly plumb.
Then attach a balancing 2X4 (kicker) to
the top portion of the unit with tie wire
and stake the other end to the ground.
If needed for stability, a second 2X4 may
be attached and staked in a different
direction.
7. Place metal pegs/rebar through
prepared holes in embedded pipe.
8. Pour concrete into footings. Use
vibration or thorough shovel mixing to ensure
a good set around embedded pipe, and to
eliminate air pockets.
9. Depending on the type of surface to be
installed, there should be approximately 4”
between the top of the concrete and “nished
grade.”

INSTALLATION INSTRUCTIONS
Model:
Name:
During installation, please be sure to also refer to guidelines in Greenelds’ Preliminary Instructions document.
© 2015 Greenelds Outdoor Fitness, Inc.
In order to honor our commitment to quality and safety, Greenelds Outdoor Fitness reserves the right to make changes and revise the design specications without notice.
Questions? Please call
888-315-9037 x105
Dimensions
Greenelds installation instructions:
1. All units MUST be fully assembled,
leveled, and braced in place in the foot-
ing hole before any concrete is poured.
2. A monolithic pour MUST be used for
concrete. (All concrete must be poured
at one time)
3. Concrete requirement: 3250 psi or better.
4. The top of the blue tape attached to the posts on the
equipment is nal top surface level.
5. All screws must be attached using LocTite.
6. It is recommended to wait a minimum of one week
after concrete is poured before equipment is used.
7. The use of Decomposed Granite Surfacing (DG) is known
to accelerate normal wear & tear of footrests.
GR2005-1-105
Custom Announcement Sign
This unit ships in 1 separately wrapped component.
75"
22"
18"
22"
18"
18"
18"
Finished product

INSTALLATION INSTRUCTIONS
Model:
Name:
© 2015 Greenelds Outdoor Fitness, Inc.
1. Clamp the two pipes between two
2X4s, using all-thread, nuts and washers.
2. Top of boards should be even with
the “nished grade” marking on pipe,
usually done with blue tape.
3. Stand unit in the prepared footing;
use laser or string-line to measure height
of unit.
4. Raise/lower unit so that “nished
grade” marking is correct
height.
5. Stake the clamping 2X4s to the
ground on each side of the unit.
GR2005-1-105
Custom Announcement Sign
6. With magnetic level, make sure
that the frame is exactly plumb.
Then attach a balancing 2X4 (kicker) to
the top portion of the unit with tie wire
and stake the other end to the ground.
7. Pour concrete into footings. Use
vibration or thorough shovel mixing to ensure
a good set around embedded pipe, and to
eliminate air pockets.
8. Depending on the type of surface to be
installed, there should be approximately 4”
between the top of the concrete and “nished
grade.”