Greenheck MS-1P User manual

Installation, Operation and Maintenance Manual
Please read and save these instructions for future reference. Read carefully before attempting to assemble,
install, operate or maintain the product described. Protect yourself and others by observing all safety
information. Failure to comply with instructions could result in personal injury and/or property damage!
1
Motor Starter Single Phase
DANGER
Indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury.
This signal word is to limited to the most extreme
situations.
WARNING
Indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury. It
may also be used to alert against unsafe practices.
This is the safety alert symbol. Read and
follow instructions carefully to avoid a
dangerous situation.
This symbol alerts the user to the presence
of “dangerous voltage: inside the product
that might cause harm or electrical shock.
!
!
Precautions and Warnings
To prevent injury and property damage, follow these
instructions. Failure to adhere to installation/operation
procedures and all applicable codes may result in
hazards as indicated by warning codes outlined below:
Safety Instructions
DANGER
Equipment starts automatically. Lockout/tagout
before servicing.
CAUTION
As with all electrical products, read manual
thoroughly. Only qualified, expert personnel should
perform maintenance and installation. Contact the
nearest authorized service facility for examination,
repair, or adjustment. Do not disassemble or repair
unit unless described in this manual; death or
injury to electrical shock or fire hazard may result.
Specifications and manual data subject to change.
Consult factory for additional information.
DANGER
HAZARDOUS VOLTAGE
• Disconnect and lock out all power before installing
or servicing equipment.
• This equipment may require locking out multiple
power sources prior to service.
• Install and wire in accordance with all applicable
local and national electrical and construction codes.
WARNING
FAILURE TO FOLLOW THESE INSTRUCTIONS
MAY RESULT IN DEATH OR SERIOUS INJURY.
!
!
Table of Contents
Installation
Mounting..................................2
Main Power Wiring ..........................2
Low Voltage Wiring..........................2
Wiring Schematic............................3
Operation
Overload Adjustment ........................2
Operation Modes ...........................2
LED Status Indicators........................2
Lockout Options ............................3
Dimensions.................................3
Product Ratings .............................3
Our Commitment ............................4
UL 508
File E258387
®
®
Document 476374
Motor Starter MS-1P
Single Phase Starter

2Motor Starter Single Phase
Main Power Wiring
Wire main power input and output to the appropriate
12AWG wire leads utilizing properly sized wire nuts. Use
only copper conductors rated at least 60°C. Maintain
proper clearances and verify that no possibility of an
electrical short exists between the power conductors or
enclosure. Ensure that wires are not under stress and all
insulation is intact.
Low Voltage Wiring
Automation system control wiring should be run in
a separate conduit. The control terminals accept
26~14AWG wire torqued to 3.5 in-lb.
1Ø AC Input 50/60 Hz
L1 L2
T1 T2
M
Voltage Input
Auto Run
Fault
Output
Status
Output
Dry Input
Auto Run
Normally Open
Input
12-120VAC/DC
Input
1. Overload Adjustment
2. Operation Mode Selector
3. Main Power / Disconnect
4. PWR Power Status LED
5. RUN Run Status LED
6. FLT Fault / Overload LED
HAND RESET
AUTO
PWR
RUN
FLT
1
2
3
4
5
6
Overload Adjustment
Confirm nameplate Full Load Amperage (FLA) to
ensure proper overload protection. Using a flathead
screwdriver, turn the adjustment dial to the desired
amperage setting. The starter is not rated to protect
loads exceeding 16 amps.
Operation Modes
RESET: To reset the starter to normal operation
following a Fault condition, slide the 3-position
switch to RESET and hold for a minimum of 5
seconds (after 180 second cool down period has
elapsed). Once starter has been reset, return switch
to the desired mode.
MANUAL (HAND MODE): In Manual or HAND mode,
the MS-1P will function as a motor disconnect or
“manual motor starter.” Select the ON (ƫ) position on
the main power switch to engage motor.
AUTOMATIC (AUTO MODE): When utilizing the
starter in the AUTO mode, a signal sent via the
terminal inputs (located on rear of unit) determine
motor operation (ON or OFF).
LED Status Indicators
POWER (PWR): Illuminates when voltage is applied
to the input terminals and main power switch is in
the ON (ƫ) position.
RUN: Under a RUN condition, the RUN LED will
remain illuminated if the MS-1P senses current
providing status. The LED will flash when the unit
does not sense current.
FAULT (FLT) - Overload Trip: The MS-1P indicates a
fault condition by flashing the red FAULT LED which
will remain constant in the event of a fault trip. The
LED will also flash if a RESET attempt is made during
the 180 second overload cool down period.
Operation
WARNING
• Do not locate starter in an environment subject to
flammable gases, dusts or materials. Contact arcing
can induce explosion or fire.
• Install starter in UL Type 1 (NEMA-1) appropriate
locations only. Safe mounting requires a dry,
protected environment.
• Do not allow any metal shavings or debris from
installation to enter enclosure.
Installation
Mounting
Mount the starter on a minimum 14 cu-in single gang
junction box. To access mounting holes, slide upper and
lower covers to the open position. (See Figure 1)
Using provided mounting screws (6-32 x 7/8-inch),
attach starter housing to junction box (once appropriate
wiring has been completed).
Figure 1
®

3
Motor Starter Single Phase
Lockout Options
To lockout, slide the lower cover upward to reveal
concealed locking grasp. Insert a standard padlock
to prevent unauthorized access or tampering. If
multiple padlocks are required, an optional padlocking
attachment can be utilized (not included).
See Figures 2A and 2B
Figure 2A Figure 2B
3.29
4.93
2.75
1.43
2.15
HAND RESET
AUTO
All dimensions in inches
Dimensions
Product Ratings
MS-1P
Horsepower 1 Horsepower
115 or 230 VAC
Short Circuit
Protection
Suitable for use on a circuit
capable of delivering not more
than IkRMS Symmetrical
Amperes, 240 volts maximum
when protected by Class J or
Class RK fuses (30 amp max)
or magnetic circuit breaker (40
amp max)
Interrupt Current Ik≤ 5kA RMS Symmetrical
Max Current 16A
Overload I2t Class 10
Reset Manual
®

4476374 • Motor Starter Single Phase, Rev. 1, March 2013 Copyright 2013 © Greenheck Fan Corporation
As a result of our commitment to continuous improvement, Greenheck reserves the right to change specifications
without notice.
Specific Greenheck product warranties are located on greenheck.com within the product area tabs and in the
Library under Warranties.
Greenheck Motor Starter catalogs provide additional
information describing the equipment and specification data.
®
Phone: [phone] • Fax: [phone] • Parts: 800.355.5354 • E-mail: [email protected] • Website: www.greenheck.com
Our Commitment
AMCA Publication 410-96, Safety Practices for Users and
Installers of Industrial and Commercial Fans, provides
additional safety information. This publication can be obtained
from AMCA International, Inc. at www.amca.org.