GreenWorks Tools 2928202 User manual

40V LITHIUM-ION BATTERY CHARGER
2928202
Important!
It is essential that you read the instructions in this manual before
operating this machine.

English (Original instructions)
2
CHARGER
SPECIFICATIONS
40V Charger: 2928202
Input: 220-240V 50-60Hz, 1A
Output: 40V 4A
DO NOT probe the charger with
conductive materials.
DO NOT allow liquid inside the charger.
DO NOT try to use the charger for any
other purpose than what is presented in
this manual.
Do not cover the ventilation slots on
the top of the charger. Do not set the
charger on a soft surface i.e. blanket,
pillow. Keep the ventilation slots of the
charger clear.
Do not allow small metal items or
material such as steel wool, aluminum
foil, or other foreign particles into the
charger cavity.
Unplug the charger before cleaning and
when there is no battery pack in the
charger.
Do not try to connect two chargers
together.
Do not use the charger in the
circumstances that the output Polarity
does not match the load polarity.
For indoor use only.
The cover may under no circumstances
be opened. If the cover is damaged,
then the charger may no longer be used.
Do not recharging non-rechargeable
batteries.
WARNING
To avoid risk of re, electric shock, or
electrocution:
Do not use a damp cloth or detergent
on the battery or battery charger.
Always remove the battery pack before
cleaning, inspecting, or performing any
maintenance on the tool.
CLEANING
Wipe the outside of the charger with a dry,
soft cloth. Do not hose down or wash with
water.
Class II
Double insulation
For indoor use only
Before charging, read the
instructions
F5A Fuse
WARNING
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety.
Children should be supervised to
ensure that they do not play with the
appliance.
Cleaning and user maintenance
should not be made by children without
supervision.
If the supply cord is damaged,it must
be replaced by manufacturer, its
service agent or similarly qualified
persons in order to aviod a hazard.
Use only with Greenworks 40V
rechargeable Li-ion battery.
CHARGING PROCEDURE
NOTE: The battery is not shipped fully
charged. It is recommended to fully charge
before use to ensure that maximum run
time can be achieved. This lithium-ion
battery will not develop a memory and may
be charged at any time.

English (Original instructions)
3
1. Plug the charger into an AC power
outlet.
2. Insert the battery pack (1) into the
charger (2).
1
2
3
This is a diagnostic charger. The Charger
LED Lights (3) will illuminate in specific
order to comunicate the current battery
status. They are as follows:
STAND BY
CHARGING
FULLY CHARGED
HIGH TEMP.
ERROR
LED 1
RED
RED BLINKING
GREEN
GREENRED
BLINKING
RED OFF
BLINKING
RED
BLINKING
GREEN
LED 2
OFF
False Defect Note:
When the battery is inserted into the
charger, LED 1 flashes RED and LED 2
flashes Green, remove the battery from
the charger for 1 minute, then reinsert. If
the status LEDs indicate normal, then the
battery pack is good. If the status LED 1
and LED 2 are still blinking, remove the
battery pack and unplug the charger. Wait
1 minute and plug the charger back in and
reinsert the battery pack. If the status LEDs
indicate normal than the battery pack is
good. If the status LED 1 and LED 2 are still
blinking then the battery pack is defective
and needs to be replaced.
CHECKING THE CHARGER
If the battery pack does not charge properly:
Check the current at the power outlet
with another tool. Make sure that the
outlet is not turned off.
Check that the charger contacts have
not been shorted by debris or foreign
material.
If the surrounding air temperature is not
normal room temperature, move the
charger and battery pack to a location
where the temperature is between 7 ˚C
and 40˚C .
CHARGER MOUNTING
1. This charger can be installed hanging
on a wall using two #8 screws (not
supplied).
2. Locate the placement for the charger to
be wall mounted.
3. If fastening to wood studs use 2 wood
screws (not included).
4. Drill two holes on center 145mm apart
ensuring that they are vertically aligned.
5. If fastening to drywall use wall
anchors(not included) and screws to
secure the charger to the wall.
NOTE: If the battery and the charger won’t
be used for a long time, please remove the
battery from the charger and pull out the
AC power plug.

English (Original instructions)
4
IMPORTANT SAFETY INSTRUCTIONS
1. SAVE THESE INSTRUCTIONS -
DANGER: TO REDUCE RISK OF FIRE
OR ELECTRIC SHOCK CAREFULLY
FOLLOW THESE INSTRUCTIONS.
2. Confirm the voltage available at each
country location before using the
charger.
3. If the shape of the plug does not fit the
power outlet, use an attachment plug
adaptor of the proper configuration for
the power outlet.
CORRECT DISPOSAL OF THIS
PRODUCT:
This marking indicates that this product
should not be disposed with other
household wastes throughout the EU. To
prevent possible harm to the environment
or human health from uncontrolled waste
disposal, recycle it responsibly to promote
the sustainable reuse of material resources.
To return your used device, please use
the return and collection systems or
contact the retailer where the product was
purchased. They can take this product for
environmental safe recycling.
Removal of waste batteries and
accumulators
Li-ion
Member States shall ensure that
manufacturers design appliances in such a
way that waste batteries and accumulators
can be readily removed. Where they
cannot be readily removed by the end-
user. Member States shall ensure that
manufacturers design appliances in such a
way that waste batteries and accumulators
can be readily removed by qualified
professionals that are independent of the
manufacturer. Appliances in which batteries
and accumulators are incorporated shall
be accompanied by instructions on how
those batteries and accumulators can be
safely removed by either the end-user or
by independent qualified professionals.
Where appropriate, the instructions shall
also inform the end-user of the types of
battery or accumulator incorporated into
the appliance.

Greenworks Tools Warranty Policy for DIY machines
PERIOD OF WARRANTY
All new Greenworks Tools machinery is supplied with a 2 year parts and labour warranty from original date of purchase. A 30 day warranty is
available for machines used professionally as Greenworks Tools are designed primarily to be used by DIY consumers.
This warranty is non-transferable.
LIMITATIONS
This warranty applies only to defective parts/components and does not cover repairs due to:
1. Normal wear and tear.
2. Routine tune up or adjustment.
3. Damage caused by improper handling/abuse/misuse or neglect.
4. Overheating due to lack of maintenance.
5. Damage due to ttings/fasteners becoming loose/detached through lack of maintenance.
6. Damage caused by cleaning with water.
7. Machines serviced or repaired by non-authorised Greenworks Tools service centres.
8. Machines incorrectly assembled or adjusted.
9. Damage caused by improper use of the machine.
10. Damage caused by improper winterisation (pressure washers)
11. Items considered as consumable parts are not normally covered by the warranty, including but not limited to:
• Batteries
• Electric cables
• Blade and blade assemblies
• Belts
• Filters
• Chucks and tool holders
12. Certain products may contain components such as engines, transmissions from an alternative manufacturer, these items will be subject to the
appropriate manufacturer’s warranty policy except where Greenworks Tools Europe GmbH agrees to underwrite any claims outside the said
manufacturer’s warranty period.
13. Second hand goods are not covered under this warranty policy.
14. The tting of spares, replacements or extra components which are not supplied or approved by Greenworks Tools Europe GmbH.
Warranty
To claim a warranty on any product under this policy a proof of original
purchase is required. Credit card statement do not qualify as sufcient
proof of purchase. In the rst instance of a warranty event occurring the
consumer should return the product to the original place of purchase with their proof of purchase. The machine will be sent to our central service
facility and an inspection made. If the machine be found to be at fault it will be repaired and sent back to the address of the consumer free of charge.
Machines that retail for less than €100 euros including sales taxes will generally be replaced.
If the central service facility nds that machine is not found to be at fault
then the consumer will be advised they will need to pay for the cost of the repair.
This warranty policy is subject to change from time to time to accommodate the needs of new products. A copy of the latest warranty policy will be
available at www.greenworkstools.eu.
EN

EN
EC DECLARATION OF CONFORMITY
Manufacturer: Changzhou Globe Co., Ltd.
Address: No. 65 Xinggang Rd., Zhonglou Zone, Changzhou, Jiangsu, China
Name and address of the person authorised to compile the technical le:
Name: Peter Söderström
Adress: Hjortronvägen 3, 555 93 Jönköping, Sweden
Herewith we declare that the product
Category ....................................................................................... 40V battery charger
Model ............................................................................................................... 2928202
Serial Number .......................................................................... See product rating label
Year of Construction ................................................................ See product rating label
is in conformity with the relevant provisions of the Low Voltage Directive 2014/35/
EU
is in conformity with the provi ions of the following other EMC directive (2014/30/
EU).
And furthermore, we declare that
the following (parts/clauses of) European harmonised standards have been used
AS/NZS 60335-2-29, AS/NZS 60335-1, EN 62233, EN 55014-1,
EN 55014-2, EN 61000-3-2, EN 61000-3-3
Place, date: Changzhou, 08/11/2017 Signature: Ted Qu Haichao
Quality Director