manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Grifco
  6. •
  7. Keypad
  8. •
  9. Grifco E840G User manual

Grifco E840G User manual

grifco.com.au
grifco.co.nz
WIRELESS KEYPAD – MODEL E840G
WARNING
To prevent possible SERIOUS INJURY or DEATH from a moving door:
•Install Wireless Keypad within sight of the door, out of reach of children at a minimum height of 1.5m, and away
from all moving parts of door.
•ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote
controls.
•Ac vate door ONLY when it can be seen clearly, is properly installed, and there are no obstruc ons to the door travel.
•ALWAYS keep the door in sight un l completely closed. NEVER permit anyone to cross the path of a moving door
•NEVER allow small children near ba eries. If ba ery is swallowed, immediately no fy your doctor.
GRIFCO FRONT PANEL
1. UP - Moves the door upwards
2. DOWN - Moves the door downwards
3. STOP - Stops the door
4. SET -
5. POWER ON - Shows when the unit is
mains powered
6. STATUS - Shows the status of the unit
7. LIMIT ERROR – When lit indicates limits
are not set
PROGRAMMING - eDrive +2.0
To program the E840G Wireless Keypad ensure the radio lock is
removed then perform the following steps:
1. Press and hold the SET bu on on the GRIFCO front panel,
then
2. While holding the SET bu on, press the STOP bu on 5 mes
(the green status light will light then con nue ashing,
indica ng learn mode)
3. Let go of the SET bu on
4. Enter a 4-digit code into the E840G keypad.
5. Press the E840G ENTER key
6. Press STOP bu on on the GRIFCO front panel to exit learn
mode.
7. Install the RADIO LOCK key on the eDrive2 board to prevent
any further wireless entry devices being learned.
E840G Wireless Keypad
ENTER key
KEYPAD

on the main PCB
2. Enter a 4-digit code on
the E840G keypad and
press enter
3. The operator will auto
exit learn mode
PROGRAMMING - S-Drive
Learn Button
Indicator LED
PROGRAMMING - LS-Drive

the operator
2. Enter a 4-digit code on the E840G
keypad and press enter
3. The operator will auto exit learn mode
PROGRAMMING - LR-Drive
“S” Button

2. Enter a 4-digit code of your choice on the Wireless Keypad



INSTALLATION
1. Select a loca on to mount the E840G Wireless Keypad at a minimum height of 1.5m out of
the reach of children
2. Remove ba ery cover and b ery.
3. Mark the top moun ng hole and drill a 3.2mm pilot hole
4. Install the top screw, allowing 3.2mm to protrude above the surface. Posi on the E840G
over the top screw
5. Mark the b m hole and drill a 3.2mm pilot hole. Install the b m screw. Do not over
ghten to avoid cracking the plas c housing.
6. Re-install b ery and replace cover.
OPERATION
The E840G opens the door from the closed posi on when the PIN is entered and ENTER bu n
pressed.
The E840G Keypad will blink for 15 seconds. During this me the E840G can be used to TOGGLE the
ac on of the door between close / stop / open if an obstruc on detec on device is installed, or
stop / open only if no obstruc on detec on device is installed.
When the E840G Keypad stops blinking, the E840G ENTER key can be used to close the door
without entering the PIN. If no obstruc on detec on device is installed, the ENTER key must remain
pressed to complete the door close sequence.
REPLACEMENT PARTS
Ba ery..............................................................................6F22 9V
Keypad Cover ...................................................................41D621-1
Ba ery Cover ...................................................................41D541
WARRANTY
ONE YEAR LIMITED WARRANTY
Chamberlain warrants to the original purchaser of this product that it is free from defect in materials
and/or workmanship for a period of 1 year from the date of purchase.
CHANGE AN EXISTING PIN PROGRAM A TEMPORARY PIN
1. Enter the programmed PIN that you want to change into the E840G keypad.
2. Press the #bu n on the E840G keypad for one second
3. Enter the new 4-digit PIN of your choice into the E840G keypad, then;
4. Press the E840G ENTER key
5. Test the new PIN to ensure it works.
A temporary 4-digit PIN can be programmed to allow access to visitors. Each programmed PIN can
program one temporary PIN. The temporary PIN can be set for a number of hours or a number of
door openings. The temporary PIN can not be the same as any previously programmed PIN.
1. Press any programmed PIN on the E840G keypad
2. Press the *bu n on the E840G keypad for one second.
3. Enter the temporary 4-digit PIN of your choice into the E840G keypad, then
4. Press the E840G ENTER key
5. Then choose between number of hours OR number of openings:
a. Press the number of hours for which the temporary PIN will work (up to 255)
(NOTE: You MUST key in at least THREE digits. For example, type ‘003’ for 3 hours or
3 openings).
b. Press the number of openings for which the temporary PIN will work (up to 255)
then press the #bu n on the E840G keypad.
6. Test the new PIN to ensure it works. (If the temporary PIN was set for a number of openings,
the test will use up ONE opening).
114A4596C

Popular Keypad manuals by other brands

Dahua ARK50C-R user manual

Dahua

Dahua ARK50C-R user manual

Arrowhead LCD Keypad operating guide

Arrowhead

Arrowhead LCD Keypad operating guide

Honeywell ADEMCO 5828 user guide

Honeywell

Honeywell ADEMCO 5828 user guide

IFM ecomatPanel CR1300 operating instructions

IFM

IFM ecomatPanel CR1300 operating instructions

Securitron DK-26W Installation & operating instructions

Securitron

Securitron DK-26W Installation & operating instructions

Topre REALFORCE 103UB quick start guide

Topre

Topre REALFORCE 103UB quick start guide

Aritech CS-175 Series user guide

Aritech

Aritech CS-175 Series user guide

GE NetworX NX-1500E user manual

GE

GE NetworX NX-1500E user manual

SkyLink GBRK Guide manual

SkyLink

SkyLink GBRK Guide manual

Targus Stow-N-Go AKP01US user guide

Targus

Targus Stow-N-Go AKP01US user guide

DSC PC5502Z2 installation manual

DSC

DSC PC5502Z2 installation manual

Sebury K2 manual

Sebury

Sebury K2 manual

DSC LCD5501Z instruction manual

DSC

DSC LCD5501Z instruction manual

GEM GEM DK-100 Specifications

GEM

GEM GEM DK-100 Specifications

Alula Connect+ RE663 quick start guide

Alula

Alula Connect+ RE663 quick start guide

UTC Fire and Security interlogix QS1500 installation instructions

UTC Fire and Security

UTC Fire and Security interlogix QS1500 installation instructions

Invertek Drives OPTIPAD user guide

Invertek Drives

Invertek Drives OPTIPAD user guide

Kensington 72274 Instruction guide

Kensington

Kensington 72274 Instruction guide

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.