Grilla Grills Pro Cart User manual

Pro Cart Assembly Guide
1
1
2
1
2
(A) Handle Grip
(B) Steering Bearing
(C) 1/2” Steering Bolt
(D) 1/2“ Steering Washer
(E) 1/2” Steering Locknut
(F) Clevis Pin/Cotter Pin
(G) 5/8” Wheel Locknut
(H) 5/8” Wheel Bolt
(I) 8”x2.5 Wheel
(J) Locking Plugs
(K) 5/16“ Mounting Bolt
(L) 5/16” Mounting Nut
(M) Wheel Washer
(N) Wheel Caps
(O) Bungee Cord
x1
x1
x1
x1
x1
x1
x2
x4
x4
x27
x42
x42
x4
x4
x1
Hardware Included Tools Needed
(0) Handle
(1) Frame base
(2) Steering Assembly
(3) Top Frame Short
(4) Top Frame Long
(5) Rear Wheel Bracket
(6) Frame Stiffener
(7) Cart Legs
(8) Cover Panels
x1
x1
x1
x2
x2
x2
x2
x4
x8
Using the mounting hardware ( K , L ) mount the
rear wheel brackets ( 5 ) to the base ( 1 ).
Attach the four cart legs ( 7 ) to the
frame base ( 1 ). Each leg gets a cover
panel ( 8 ). All secured with mounting
hardware ( K , L ).
*Make sure Legs are facing Inward
• 5/16”, 1/2“, 1” Open ended Wrench
or an Adjustable Cresent Wrench
of size.
• -IMPORTANT- Your 4 Exisitng
Silverbac Cart screws
7
18
5
5
1

Pro Cart Assembly Guide
3
4
5
2
Next loose fit both top frame short pieces ( 3 )
and remaining cover panels (8)with mounting
hardware ( K , L ).
4Now Slide in both top frame long pieces (4).
Secure with mounting hardware (K,L)as
well.
Tighten up all mounting hardware ( K , L )
after both short & long frame pieces ( 3, 4 )
have been installed.
3
3
8
8
4
4
8
8

6
7
8
3
Turn the cart on one end with the rear
wheel bracket (5)facing up. Mount the
two 8” wheels (I)with 5/8” wheel bolts
(H)and locknut ( G ) and Wheel washer
(M).
On the opposite end install the
steering assembly (2)to the
frame base ( 1 ). Use the steering
hardware ( B , C , D , E ).
With the steering assembly (1)
on, mount the two remaining 8”
wheels ( I ) with the remaining
5/8” wheel bolts ( H ) thread
onto Steering Assembly ( 1 ).
Placing the supplied wheel
washers (M) after the wheel.
Once wheels are in place
install wheel caps (N).
2
Pro Cart Assembly Guide
9
Left (L) and Right (R) Identification
marks are on each wheel inside the
rim.

9
10 4
Mount the frame stiffeners ( 6 ) to the frame base ( 1 )
with the mounting hardware ( K , L ).
Attach the handle grip ( A ) to the handle (0)
and secure with the clevis/cotter pins ( F ).
Make sure to install the handle (0)in the
upright postion.
6
0
6
Pro Cart Assembly Guide

11 5
Mount your silverbac to the cart with the
exisiting screws you used to originally mount
your grill to the stock silverbac cart.
Pro Cart Assembly Guide
Push plugs (J) in open
holes around cart.
Bungie Cord (0)
connects the grease
cup holder to frame
base