Gronomics PB18-24-45 User manual

GRONOMICS®
“MINIMAL ASSEMBLY REQUIRED”
PLANTER BENCH
Parts Check List and Assembly Instructions
STEP I
A) Unpack all of the parts and organize them in ‘like’ stacks. Please read the instructions
in its entirety before beginning assembly.
You should have: Model #PB18-24-45
QUANTITY
PART DESCRIPTION
PART #
BOX 1 of 2
6
4” x 4” x 30” Post w/13” Dovetail Depth
7009
1
4” x 4” x 36” Three Sided Dovetail Corner Post (Left)
7003-Lt
1
4” x 4” x 36” Three Sided Dovetail Corner Post (Right)
7003-Rt
1
21” x 5½” x 1” Side Rail w/Double Cleat (Left)
7004-Lt
1
21” x 5½” x 1” Side Rail w/Double Cleat (Right)
7004-Rt
2
21” x 5½” x 1” Side Rail w/Cleat
7005
4
21” x 5½” x 1” Side Rail
7007
2
14½” x 5½” x 1” Side Rail
1450
4
14½” x 2½” x 1” Narrow Center Side Rail
1451
4
15½” x 5½” x 1” Bottom Board
1550
2
15½” x 4½” x 1” Corner Notched Bottom Board
1551
8
4½” x 4½” x 1½”Post Cap
3100
2
18”x 34”Fabric Liner
2002
BOX 2 of 2
1
Planter Bench (pre-assembled)
7110
3
45” x 5½” x 1” Side Rail (One w/Logo)
4501, 4501L
4
21” x 2½” x 1” Narrow Center Side Rail
7006
6
14½” x 5½” x 1” Side Rail
1450
2
15½” x 4½” x 1” Corner Notched Bottom Board
1551
6
3” Screws
7008

GRONOMICS®
“MINIMAL ASSEMBLY REQUIRED”
Packaged & Inspected by:___________________________________ Date____________________
STEP II
A) Start by standing up the two 4” x 4” x 36” 3-sided
dovetail corner posts with arched dovetail slot facing
toward center.
B) Slide the three 45” x 5½” x 1” side rails into the posts
to make the backrest. Placing the 45” x 5½” x 1” side
rail with logo on top.
C) Stand the six 4” x 4” x 30” posts w/13” dovetail depth
in position.
D) Slide the 21” x 5½” x 1” side rail w/double cleat from
the back center posts into the two front 4” x 4” x 30”
post. With the shorter cleat facing toward the center of
bench. Slide the 21” x 5½” x 1” side rail w/cleat to
connect the outer two 4” x 4” x 30” posts. (see figure 1
and 2)
STEP III
A) Slide the 14½” x 5½ x 1” side rails, followed by the
14½” x 5½ x 1” narrow center side rail and the last
14½” x 5½ x 1” side rails between the posts to
complete the outer planter boxes. (see figure 2)
B) Place the two 15½” x 4½” x 1”corner notched bottom
boards on the end cleats. Make sure the corner cut-out
notches are in the corners.
C) Carefully remove the screw covers that are protecting
the cap screws. Place the cap on the center of the
screw utilizing the pre-drilled hole in bottom of the
cap. Do not over tighten. (see figure 4)
STEP IV
A) Place the planter bench seat in position. To reinforce
the bench use the six screws underneath the bench in
the pre-drilled holes. (see figure 3)
B) Place the two fabric liners on the bottom of the planter
boxes.
NOTE: If you need assistance with parts or have assembly
questions, please contact Customer Service either via email at
[email protected] or phone at 763-753-7374
Recommended Finish: A natural oil non film-forming finish designed for Cedar.
If Cedar is not finished checking may occur and will naturally turn a weathered
gray color. 1-Year Warranty: All Gronomics®products are warranted against
all manufacturing defects of material or craftsmanship for a period of ONE full
year from date of purchase. Warranty does not cover cracking, damage caused
(Figure 1)
(Figure2)
(Figure 3)
(Figure 4)
Pre-drilled holes
21” x 5½” x 1” side rail w/double cleat
Left side
le