GrowSpan Estate Elite 104609 User manual

1
GROWSPAN™ESTATE ELITE GREENHOUSES
Revision date: 01.01.16
104609 11'-8" W x 8'-10" H x 16'-6" L
104611 11'-8" W x 8'-10" H x 24'-8" L
Photo may show a different but similar model.
STK# DIMENSIONS
GrowSpan™
Estate Elite Greenhouses
©2016 GrowSpan
All Rights Reserved. Reproduction
is prohibited without permission.

GROWSPAN™ESTATE ELITE GREENHOUSES
2Revision date: 01.01.16
YOU MUST READ THIS DOCUMENT BEFORE YOU
BEGIN TO ASSEMBLE THE SHELTER.
Thank you for purchasing this GrowSpan™ greenhouse.
When properly assembled and maintained, this product will
provide years of reliable service. These instructions include
helpful hints and important information needed to safely
assemble and properly maintain the greenhouse. Please
read these instructions before you begin.
SAFETY PRECAUTIONS
• Wear eye protection and gloves when handling panels
and frame parts.
• Frame is metal. Use a portable GFCI when working
with power tools and cords.
• Do not climb on the greenhouse or framing during or
after construction.
• Do not occupy the greenhouse during high winds,
tornadoes, or hurricanes.
• Provide adequate ventilation if the structure is
enclosed.
• Do not store hazardous materials in the greenhouse.
• Provide proper ingress and egress to prevent
entrapment.
ANCHORING INSTRUCTIONS
Prior to assembling this greenhouse, please read the
MUST READ document included with the shipment.
WARNING: The anchor assembly is an integral part
of the greenhouse construction. Improper anchoring
may cause greenhouse instability and failure of the
structure. Failing to anchor the greenhouse properly
will void the manufacturer’s warranty and may cause
serious injury and damage.
LOCATION
Choosing the proper location is an important step before
you begin to assemble the structure.
The following suggestions and precautions will help you
determine whether your selected location is the best
location.
• Never erect the structure under power lines.
• Identify whether underground cables and pipes are
present before preparing the site or anchoring the
structure.
• Location should be away from structures that could
cause snow to drift on or around the building.
• Do not position the greenhouse where large loads
such as snow and ice, large tree branches, or other
overhead obstacles could fall.
• Always check local building codes before you begin.
SITE
After choosing a location, proper preparation of the site is
essential. The following site characteristics will help ensure
the integrity of the structure.
• A level site is required. The site must be level to
properly and safely erect and anchor the structure.
• Drainage: Water draining off the structure and from
areas surrounding the site should drain away from the
site to prevent damage to the site, the structure, and
contents of the structure.
WARNING: The individuals assembling this structure
are responsible for designing and furnishing all
temporary bracing, shoring and support needed during
the assembly process.
For safety reasons, those who are not familiar with
recognized construction methods and techniques must
seek the help of a qualified contractor.
ASSEMBLY NOTE
The assembly of this greenhouse is not complex; however,
it does take time and additional assistance. For best
results, read through these instructions before you begin to
get an overview of the entire assembly. Then, follow these
instructions as presented.
Examine all diagrams and photos and verify that you have
selected the proper parts from the correct box or boxes. Do
not mix parts from different boxes. When checking parts,
place the parts back into the same box they were removed
from and continue with the next box.
IMPORTANT! INVENTORY THE PARTS
1. Open one box and use the Bill of Material included in
that box to inventory the contents. See Page 39 for Box
9-4 (104611) or Box 7-4 (104609) for cresting parts.
2. Return all parts and the Bill of Material to the box and
repeat the procedure for all remaining boxes.
3. Call Customer Service at 1.800.245.9881 to report
any missing parts before you begin assembling the
greenhouse.

3
GROWSPAN™ESTATE ELITE GREENHOUSES
Revision date: 01.01.16
ASSEMBLY PROCEDURE
Following the instructions as presented will help ensure
the proper assembly of your greenhouse. Failing to follow
these steps may result in an improperly assembled and
anchored greenhouse and may void all warranty and
protection the owner is entitled.
The steps outlining the assembly process are as follows:
1. Verify that all parts are included in the shipment. Notify
Customer Service for questions or concerns.
2. Read these instructions and all additional
documentation included with the shipment before you
begin assembling the greenhouse.
Use these instructions and the Bill of Material (inside
each box) when assembling the greenhouse.
3. Gather the tools, bracing, ladders (and lifts if
applicable), and assistance needed to assemble the
greenhouse.
4. Re-evaluate the location and site based on the
information and precautions presented in the
documentation included with the shipment.
5. Lay out the site (if this has not been completed).
6. Assemble the base frame (additional purchase
required) and greenhouse components in the order
they are presented in these instructions.
7. Anchor the greenhouse as instructed.
8. Read the greenhouse care and maintenance
information at the end of these instructions.
9. Complete and return all warranty information as
instructed.
REQUIRED TOOLS
The following list identifies the main tools needed to
assemble the shelter. Additional tools and supports may be
needed depending on the structure, location, and
application.
• Tape measure or measuring device
• Metric and standard wrench set (or ratchet and socket
set)
• Phillips screwdriver
• Needle-nose pliers
• Ladders and/or work platforms
• Caulk gun for silicone application
• Utility knife
GREENHOUSE PARTS
All greenhouse sections (e.g., roof, sides, end walls, etc.)
are shipped in individually numbered boxes. The quantity of
boxes may differ depending on the greenhouse.
To prevent mixing the parts while assembling the
greenhouse, select the boxes as instructed and open that
box only and assemble its contents.
OPEN BOXES AS INSTRUCTED TO PREVENT MIXING
OF THE CONTENTS.
NOTE: Some photos and diagrams throughout these
instructions may show a greenhouse with slightly different
dimensions, color, or design. The assembly procedures
are identical regardless of these differences. Notable
differences are addressed.
For a quick overview of this greenhouse, consult the
diagrams in the Quick Start section near the back of these
instructions.
Those not familiar with the assembly of similar structures
and the use of common hand tools must seek the
assistance of someone with such experience.
PART IDENTIFICATION NUMBERS
All main parts include a stamped ID number. Use this
number when selecting the required parts during the
assembly.
1617
1617
NOTE: The locations of the part numbers on the
components may vary. Refer to the Bill of Materials shipped
within each box for a description of each part.
WARNING: Do not allow the polycarbonate panels to
remain in direct sunlight until they are installed. Doing
so will cause the protective film to become difficult if not
impossible to remove.
Consult Page 40 for additional polycarbonate
information. And, Step 10 on that page, for "how to use
vent tape" (additional purchase required) information
before installing any polycarbonate panel.

GROWSPAN™ESTATE ELITE GREENHOUSES
4Revision date: 01.01.16
Ridge Beam
Rafters
OVERVIEW
This section is an overview of the process for assembling
your Elite Greenhouse. See illustration below to identify
main parts of greenhouse.
1. Locate the required parts for each assembly procedure.
2. Preassemble the base frame (additional purchase
required), end walls, and side walls as instructed.
3. Assemble the frame and install the ridge beam, rafters,
vents, and vent panels.
4. Square and anchor the greenhouse.
5. Assemble and attach doors and install door panels.
6. Install all remaining polycarbonate panels.
7. Attach drain pipes and remaining door hardware. Vent
Double Door
Diagonal
Strut
Base Rail
Gutter Rail
Vertical Support:
Side Wall
Drain Pipes
NOTE: Model shown below may differ slightly from the actual Elite
model. No cresting is shown.
ATTENTION: TO AVOID TWISTING OFF OR DAMAGING
THE FASTENERS, DO NOT OVERTIGHTEN.
FOR YOUR CONVENIENCE, ADDITIONAL FASTENERS
CAN BE FOUND IN THE "EXTRA PARTS" BAG OR BOX.
REFER TO THE BILL OF MATERIALS FOR A LIST OF
THE FASTENERS CONTAINED IN THAT BAG OR BOX.
Estate Elite Greenhouses

5
GROWSPAN™ESTATE ELITE GREENHOUSES
Revision date: 01.01.16
BASE FRAME ASSEMBLY (OPTIONAL PURCHASE)
The base frame assembly provides a level, square surface
on which to set the greenhouse frame. It is strongly
recommended that you use this base.
The optional base (additional purchase required) is
assembled and squared, its posts set into the ground.
It is then anchored in place using ground posts or
other approved anchoring methods described in these
instructions.
This base is an optional purchase. Contact your sales
consultant at 1-800-245-9881 to purchase the base.
The following steps describe how to assemble the optional
base frame for the greenhouse.
1. Unpack the base kit to identify the parts.
NOTE: The base is assembled upside down and then
is flipped when it is positioned on the site.
2. Identify the base channel lengths used for the ends
(width) and the sides (length).
3. Select the first frame support post and the required
nuts and bolts and place these at one corner of the
base.
ATTENTION: If you plan to place the base on a
concrete slab or patio, you must remove the "leg"
portion of the frame support posts. Before you
assemble the base as shown below, cut the frame
support posts so they are the same length as the base
channel is wide.
Support
Post
Base
Channels
Cut these only if you plan to place the frame, and
ultimately the greenhouse, on a concrete slab.
4. Insert two bolts through the pre-drilled holes in the post
and one base channel and add the nuts.
NOTE: Do not tighten the bolts at this time.
5. Select the remaining bolts and repeat the previous step
to attach the remaining base channel to the support
post.
Leg portion of
frame support post
IMPORTANT:
Dashed line shows
where to cut when
removing the
leg for use on
concrete only.
Support Post

GROWSPAN™ESTATE ELITE GREENHOUSES
6Revision date: 01.01.16
BASE FRAME ASSEMBLY (CONTINUED)
6. Verify that the post is straight and tighten the bolts
7. Repeat the procedure to attach the remaining support
posts to the base channels.
For strength, position short base sections (if equipped)
diagonally from each other as shown.
8. After the frame is assembled and all bolts are tight, flip
the base over and set it on the site.
9. Continue with the next procedure.
NOTE: If additional legs are present, use the longer
bolts included with the kit to secure the legs to the
frame.
SQUARE THE BASE
Before the support posts of the base are driven into the
ground and before the assembled greenhouse frame is
set on and secured to the base, you must square the base
assembly and anchor the base to the site.
ATTENTION: If you are setting the base and greenhouse
on a patio or concrete slab, set the assembled base on site
and continue with the greenhouse assembly procedures
that follow. Do not square the base at this time.
This base and greenhouse require a level site. Before
setting the base or greenhouse frame (or both) in place,
you must level the site.
The easiest way to square the base is to measure
diagonally from corner to corner.
Complete these steps:
NOTE: The following procedure describes how to square
the base on a prepared site and drive the base support
posts into the ground.
1. Position the assembled base on the site as shown
below.
2. Measure diagonally from corner-to-corner.
Top of
base
NOTE: The frame is square when both measurements
are the same.
3. When the frame is square, tap the support posts into
the ground to set the frame in place and recheck the
measurements.
NOTE: Place a block of wood on top of the base
channel and support post and hammer on the wood to
protect the frame when driving the posts into place.
4. Continue to drive the posts to the desired depth.
NOTE: Use a level (or string a line) to verify that the
base remains level when set into the ground
5. After setting the base on the site, continue with the
greenhouse assembly.
Top of
base
PACKING LIST NOTE (OPTIONAL BASE FRAME ONLY)
Some packing lists included with the optional base kit may show
J-clips as an included item. These J-clips are no longer used and
are not included in the shipped items.
The self-tapping screws are now included and are used instead.
Consult the anchoring instructions within this document for
additional information.

7
GROWSPAN™ESTATE ELITE GREENHOUSES
Revision date: 01.01.16
ASSEMBLE THE END WALL FRAMES
The greenhouse has two end walls: one is the door end
and one is the non-door end.
Photo shows vertical frame member for end walls. The bolt
track is installed to the inside of the greenhouse.
IMPORTANT: To prevent loosing parts, assemble all
frame components on a flat surface. A concrete driveway
or a garage floor works best. As you assemble the frame
sections, the inside of the frame will face up as shown in
the photos that follow.
Complete the following steps to assemble the first end wall
frame. Consult the End Wall Diagrams near the back of
these instructions for part identification before you begin.
Assemble the door end first.
1. Open the package for your greenhouse. (See above
note if needed.) This package includes the parts to
assemble the end wall frames. Consult the End Wall
Diagrams for part identification.
2. Locate the top bracket used to join the upper supports
to each other at the peak of the end wall.
Bolt Track
NOTE: The holes in the top bracket are oblong as
shown.
3. Locate the two upper supports for the end wall.
The upper supports include pre-drilled holes, bolt
tracks, and a beveled end.
4. With the upper supports positioned as shown below,
secure the 1617 bracket to the supports.
View looking down on the assembled upper supports.
Joined upper supports as seen from the inside of the
greenhouse.
1617
1616 1615
1617
To the outside of
the greenhouse
1616
1615
1616 1615
Verify that the slot at the top of each upper support is
fully visible before you tighten the bolts to secure the
1617 angled bracket to the upper supports. See the
photo above.
1616 1615
1617
Slots
Greenhouse Sku Number Open this box:
104609 C/No. 7-1
104611 C/No. 9-1
For the best results and to prevent mixing parts, assemble
each end wall separately as described below. All bolt tracks
in the frame members are installed to the inside of the
greenhouse. All diagrams and individual photos shown in
these end wall instructions show the inside surface of the
frame unless otherwise noted.

GROWSPAN™ESTATE ELITE GREENHOUSES
8Revision date: 01.01.16
5. Locate one (1) 1618 angled bracket and attach it to the
end of one upper support. Do not tighten bolts.
ASSEMBLE THE END WALL FRAMES (CONTINUED)
6. Locate another angled bracket and attach it to the end
of the other upper support. Do not tighten bolts.
8. Slide two (2) bolts into the bolt track and install the
1618 bracket as shown. Do not tighten bolts.
Assembled Upper End Wall Frame
1615
1616
The assembled upper end wall frame is shown above
and includes the top bracket, two (2) angled brackets,
and two (2) upper supports.
7. Select one (1) 1614 lower support and position it as
shown below. Align the slots in each frame member.
Upper Support
1615 1618 Position the
slot in the
upper support
as shown.
1614
Align the
slots.
The dashed line
shows the bolt
track location.
Slide mounting
bolts into this track
to secure bracket.
Nuts will be
removed when the
bracing is installed.
1618
Verify that
the slots are
aligned as
shown.
9. Verify that the four bolts are loose and place the
template into position as shown in the photos below.
ATTENTION: The template is used to set the proper
clearance for the gutter rail. The template slides into
the slots in each frame member.
10. With the template in position, tighten the bolts to secure
the bracket to the upper frame member of the end wall.
See the arrows above.
Template
1614
template

9
GROWSPAN™ESTATE ELITE GREENHOUSES
Revision date: 01.01.16
11. Slightly tighten the lower two bolts and remove the
template. These bolts are loosened in a later step to
install the end wall horizontal and diagonal bracing.
Photo above shows the assembled end wall up to this
point. View shows the inside surface of the frame.
ATTENTION: Seat each lower support tight against the
top surface of the base rail.
14. Verify that each lower-support-to-base-rail connection
is square and tighten the bolts.
15. Refer to the End Frame diagram and select the two (2)
end wall vertical supports shown below.
A
Inside
outside
1616 1615
1614 1614
ATTENTION: ALL
DIAGRAMS AND
PHOTOS SHOW THE
ASSEMBLY FROM THE
INSIDE OR BOLT TRACK
SIDE OF THE FRAME
DURING ASSEMBLY.
12. Repeat the steps to attach the other 1614 lower end
wall support and to set the gutter rail clearance using
the template as previously described.
13. Locate the base rail (1610) for the end wall and attach
it to each of the lower supports as shown below.
1614
1615
Clearance
set using the
template.
1614
1616
ATTENTION: Do
not fully tighten the
lower bolts. These
are loosened and
retightened after the
bracing is installed
in a later procedure.
Vertical Support
Bolt
Track
1611-2 1611-1
ASSEMBLE THE END WALL FRAMES (CONTINUED)
Base Rail
1610
A90°
1614

GROWSPAN™ESTATE ELITE GREENHOUSES
10 Revision date: 01.01.16
16. Slide four (4) bolts into the track of each vertical
support and attach the top of each support to the upper
end wall supports and the bottom of each support to
the base rail. Do not tighten these bolts at this time.
ATTENTION: The remaining two (2) bolts in each
vertical—those between the top and bottom bolts—are
used to secure the short horizontal braces and the
diagonal struts. See the End Frame diagrams if
needed.
ASSEMBLE THE END WALL FRAMES (CONTINUED)
ATTENTION: Do not fully tighten the bolts at this time.
20. Select the 16110 bracket and attach it as shown below
using three (3) of the bolts remaining in the bolt track.
Tighten the bolts to secure the 16110 bracket to the
end wall frame.
21. Repeat the step and attach the remaining 16110
bracket to the remaining vertical frame member.
1612-2
1612-1
NOTE: After
completing this
step, each vertical
from the previous
step should be
attached at the
top and bottom
and five (5) bolts
should remain
between the top
and bottom bolts.
1613
B
Install the beveled end of the frame member at the top
and with the angle of the end wall upper supports.
17. Select the next two (2) vertical supports for the end wall
and insert seven (7) bolts into the bolt track of each
vertical. (Door end frame only.)
Dashed line shows
the beveled top of
the end wall frame
members.
View shows the
end wall from the
outside.
1615
18. Attach each vertical to the upper supports of the frame.
See the circles above. Do not tighten bolts.
Diagonal
Strut (1613)
B
IMPORTANT: At this point, two (2) bolts should remain
in each of the vertical frame members. These bolts are
used in the next steps.
22. Slide one of the two remaining bolts in the frame
member up to the bottom of the 16110 bracket. Repeat
this step for the remaining vertical frame member.
19. Add a diagonal strut to the frame and install the bottom
bolts. See the circles above for bolt location.
1612-2
16110
Photo shows the
installed 16110
bracket as seen
from inside the
frame.
16110
Slide a bolt up to here
in each of the bolt
tracks (Step 22).

11
GROWSPAN™ESTATE ELITE GREENHOUSES
Revision date: 01.01.16
23. Locate the horizontal braces and attach these to the
end wall frame. Do not use the bolt from Step 22.
ASSEMBLE THE END WALL FRAMES (CONTINUED)
ATTENTION: Use a carpenter's square or similar tool
to verify that a 90° angle is maintained at the point
where the horizontal brace is attached to the vertical
frame members of the end wall. See example below.
24. Tighten the bolts to secure the horizontal brace to the
end wall frame.
25. Repeat the steps to install the remaining brace.
NOTE: At this point, one bolt should remain unused in
each of the two frame members. This bolt is used to
secure the door header (1665) to the end wall frame.
Verify that one (1) bolt is present to secure each end of
the 1665 header. If you need to install or reposition a
bolt, loosen the horizontal brace bolts as needed, make
the necessary adjustments, and retighten.
26. Locate the 1665 header and slide five (5) bolts into the
bolt track.
27. Attach a 1665-1 flat bracket to each end of the 1665
header. Do not fully tighten the bolts at this time.
28. Attach the header and flat brackets between the
vertical frame members as shown below.
Bolt
1612-1
1619-1
C
1615
1613
D
1619-1
C
D
C
90° 90°
D
NOTE: Use the final bolt (Step 22) in each of the
vertical frame members to secure each 1665-1 bracket.
Do not tighten these bolts at this time.
29. Locate the 1612-3 vertical frame member and attach it
between the header and the peak of the end wall.
E
1665
1612-2
1612-1
E
1665
16110
1665-1 Bolt from
Step 22
1612-1
NOTE: Consult the photos on the following page for
additional details.
1612-3
F
G

GROWSPAN™ESTATE ELITE GREENHOUSES
12 Revision date: 01.01.16
ASSEMBLE THE END WALL FRAMES (CONTINUED)
30. After completing the frame for the doors, consult
the end wall diagram for the non-door end of the
greenhouse and repeat the procedure to assemble that
end wall frame.
ATTENTION: The remaining end wall frame does not
include an upper door frame member. In addition, the
small horizontal braces of the first end wall frame have
been replaced by a single, longer horizontal brace.
Keep these changes in mind as you complete the
assembly of the remaining end wall frame.
Consult the diagram near the back of these instructions
to view the non-door end wall components.
31. After assembling the end wall frame for the non-door
end, set both end wall frames aside and continue with
the sidewall assembly procedure that follows.
1612-3
1665-1
1665
G
Do not fully tighten the bolts. The header (1665) and
the vertical frame member (1612-3) are adjusted and
secured when the doors are installed later in these
instructions. Bolt should be snug to secure the header.
F
1612-3
Bolts
1616 1615
Space is reserved for customer notes.
EXTRA PARTS PROVIDED FOR GREENHOUSE
ATTENTION: TO AVOID TWISTING OFF OR DAMAGING
THE FASTENERS, DO NOT OVERTIGHTEN.
FOR YOUR CONVENIENCE, ADDITIONAL FASTENERS
AND PLASTIC MOLDING CAN BE FOUND IN THE
"EXTRA PARTS" BAG OR BOX.
REFER TO THE BILL OF MATERIALS FOR A LIST OF
THE FASTENERS AND MOLDING CONTAINED IN THAT
BAG OR BOX.
The plastic profile can be trimmed to the required length if
a piece is misplaced or damaged during installation.
IMPORTANT: Consult the "extra parts" for items you
need before contacting customer service to request a
replacement for damaged or missing parts or fasteners.

13
GROWSPAN™ESTATE ELITE GREENHOUSES
Revision date: 01.01.16
SIDEWALL ASSEMBLY: First Two (2) Sections
After both end wall frames are assembled, locate the next
box (identified below) for your greenhouse and assemble
the first two sections of sidewall framing.
For the best results and to prevent mixing parts, assemble
each side wall separately as described. All bolt tracks
in the frame members are installed to the inside of the
greenhouse. All diagrams and individual photos shown in
these sidewall instructions show the inside surface of the
frame unless otherwise noted.
Required parts for the first two (2) sidewall frames:
Greenhouse Sku Number Open this box:
104609 C/No. 7-2
104611 C/No. 9-2
Part Number Quantity
1631 6
1632-4 2
1630-4 2
1633 4
Square-Head Bolts (short) See frame diagram.
Square-Head Bolts (long) See frame diagram.
Nuts for all bolts Same as bolt quantity.
HINT: For best results, select the parts using the table
above and the sidewall frame diagrams. Position all
parts on a flat surface and arrange them according to the
sidewall diagram. After the parts are in place, take the
required bolts and connect the pieces.
The following steps describe assembling two identical
sidewall frames. Complete these steps:
1. Open the box (indicated above) for your greenhouse
and, using the table above, gather the parts to
assemble the first two (2) sidewall sections.
ATTENTION: PLACE ALL OTHER PARTS BACK
INTO THE BOX UNTIL THEY ARE NEEDED LATER
DURING THE ROOF ASSEMBLY PROCEDURE.
2. Use the following photos and diagrams to layout and
connect the sidewall frame components.
NOTE: It may be necessary to remove or loosen bolts
(used during this procedure) when the sidewall frames
are attached to the end wall frame.
The two side frames should match when the
assembled frames are placed side-by-side with the bolt
tracks together.
3. After assembling the first two (2) sidewall frame
sections, set them aside and continue with the next
procedure to assemble a main frame mid rafter.
Diagrams and Photos for Sidewall Assembly
The circles show where to use the longer, square-head
bolts. The circle marked with an A (below) shows the long
bolt that is slid into the end wall bolt track during the frame
assembly.
ATTENTION: View of the sidewall is from the inside (or bolt
track side) for one side frame and from the outside for the
other side frame. When placed together with the bolt tracks
inward, the frames match and the diagonals will line up.
Gutter Rail 1632-4
The diagonal shown to the
right can be installed now
or when the sidewall frame
is attached to the end wall
frame. Do not fully tighten
this bolt at this time.
1630-4
Base
Rail
Consult the full
sidewall frame
diagrams near
the back of these
instructions
for additional
information.
Toward
the End
Frame
1632-4
1630-4
1633 1633
163116311631
A
This edge will
be attached to
the end wall
with the door
frame.

GROWSPAN™ESTATE ELITE GREENHOUSES
14 Revision date: 01.01.16
ASSEMBLE MAIN FRAME MID RAFTER
The mid rafter (or rafters) for the greenhouse are positioned
between the individual sidewall frame sections. Consult the
tables that follow and the diagrams to assemble the mid
rafter (or rafters) for your greenhouse.
Greenhouse Sku Number Open this box:
104609 C/No. 7-3
104611 C/No. 9-3
For the best results and to prevent mixing or misplacing
parts, remove the necessary parts (identified below) from
the box and assemble the mid rafter as described.
All diagrams and photos shown in this procedure show the
inside (or bolt-track) surface of the mid rafter unless noted.
Select these parts to assemble one (1) mid rafter:
Part Number Quantity
1614 2
1615 1
1616 1
1694 2
1617 1
16100 2
16101 2
16102 2
16103 2
Template See end frame steps.
Hex-Head Bolts 10
Square-Head Bolts (short) See photos.
Nuts for all bolts Same as bolt quantity.
HINT: For best results, position all parts on a flat surface
and arrange them according to the photos. After the parts
are in place, take the required bolts and connect the parts.
The following steps describe assembling one (1) mid rafter:
1. Open the box (indicated above) for your greenhouse
and, using the table, gather the parts to assemble the
mid rafter.
ATTENTION: PLACE ALL OTHER PARTS BACK INTO
THE BOX UNTIL THEY ARE NEEDED.
2. Use the following photos and diagrams to layout and
connect the sidewall frame components.
3. Once the mid rafter is assembled, connect the
assembled sidewall frames to the door end wall and
then attach the mid rafter to the assembled frame.
4. After the frame assemblies are connected, install the
ridge beam as instructed.
Assemble Upper Mid Rafter
1615
1616
1617
Complete these steps to assemble the mid rafter.
1. Using Steps 2-4 of the Assemble the End Wall Frames
procedure (Page 7), connect the upper mid rafter
components.
Assembled Main Frame Mid Rafter
2. Slide four (4) bolts into the bolt track of one upper
support. See the next photo. Two bolts are used to
attach the diagonal bracing in a later procedure.
3. Using two of the bolts (Step 2), attach the 1694 bracket
to the upper and lower support. Photo below shows
the assembly of one side of the mid rafter. Use the
template to set the proper spacing.
ATTENTION: Verify that the notch shown by the arrow
above is positioned as shown.
4. Tighten bolts, remove the template, and repeat the
steps to attach the remaining 1614 lower support.
1616 1615
1614 1614
Mid Rafter Diagonal Bracing
NOTE: The mid rafter is built using the same upper and
lower supports found in the end wall framing.
1614
1694
Position
notch as
shown.
1615
Template

15
GROWSPAN™ESTATE ELITE GREENHOUSES
Revision date: 01.01.16
NOTE: To this point, the mid rafter should resemble the
one in the photo below.
ASSEMBLE THE MID RAFTER (CONTINUED)
1616 1615
1614 1614
It may be necessary to loosen and reposition some
of the brackets during the assembly of the diagonal
bracing of the mid rafter.
5. Add the diagonal brackets as shown in the following
photos to complete the mid rafter assembly.
ATTENTION: The photos that follow show how to
assemble and attach the diagonal bracing for one side
of the mid rafter. Use the hex-head bolts.
16102
16101
1
Hex-Head Bolts
16102
16103
2
NOTE: Do not fully
tighten this mounting
bolt at this time.
Hex-Head Bolt
16102
16100
3
NOTE: Use Hex-Head
Bolts to attach the
brackets.
3
2
1614
1
16103
16100
1615
16101

GROWSPAN™ESTATE ELITE GREENHOUSES
16 Revision date: 01.01.16
6. Place the assembled bracing in position and attach it to
the upper and lower supports as shown below.
After attaching the assembly, slide it up or down in
the track to align the final horizontal brace with the
remaining bolt in the track of the 1614 support.
Use a carpenter's square or similar tool to square the
connection and tighten all bolts to secure the diagonal
brace assembly to the 1614 lower support.
7. Repeat the steps to assemble the bracing for the other
side of the mid rafter to complete this procedure.
8. Once the mid rafter is complete, continue with the next
procedure to assemble the first greenhouse section.
NOTE: Before you attach the lower bracket (2) of the
bracing to the support, slide one bolt into the track to
attach the horizontal bracing (3).
1
Align the bolts with the bolt holes in the bracket and
install the nuts. Do not tighten at this time.
1614
2
3
1614
ASSEMBLE THE MID RAFTER (CONTINUED)
1
2
3
NOTE: The X shows the
position of an additional
bolt slid into the track to
attach the horizontal brace
to the 1614 lower support.
X
ATTENTION: TO AVOID TWISTING OFF OR DAMAGING
THE FASTENERS, DO NOT OVERTIGHTEN.
FOR YOUR CONVENIENCE, ADDITIONAL FASTENERS
CAN BE FOUND IN THE "EXTRA PARTS" BAG OR BOX.
REFER TO THE BILL OF MATERIALS FOR A LIST OF
THE FASTENERS CONTAINED IN THAT BAG OR BOX.

17
GROWSPAN™ESTATE ELITE GREENHOUSES
Revision date: 01.01.16
2. With assistance, lift the end wall and first sidewall
frame into position as shown.
3. Slide a long bolt into the bolt track of the lower support
(1614) of the end wall. Use a piece of tape to keep it
from dropping to the bottom if desired.
4. Slide a short bolt and nut into the bolt track of the upper
support, align the slot in the base rail with the bolt track
in the upper support, and tighten the upper bolt.
ASSEMBLE THE FIRST GREENHOUSE SECTION
The following steps describe how to connect the
greenhouse components you have assembled up to this
point. These steps are repeated as other greenhouse
sections are added.
ATTENTION: For best results, connect the assembled
greenhouse sections on a flat surface as shown.
Required parts to complete these steps:
• Assembled end wall (door end)
• Assembled sidewall frames (2)
• Assembled mid rafter (1)
• Ridge Beam (1650-4) from Box 7-2 (SKU: 104609) or
9-2 (SKU: 104611)
• Square-head bolts from Box 7-2 (SKU: 104609) or 9-2
(104611)
After the above sections are connected, the greenhouse
will appear as shown in this diagram:
Complete the following steps.
1. Position the assembled frame sections as shown below
with the bolt tracks or inside surface facing up.
NOTE: Some frame photos may be of a different
model. The assembly process is the same.
Gutter Rail
Gutter Rail
Base Rail
Inside of the frame.
Gutter Rail
Gutter Rail
Slide a long bolt
into the track.
Dashed line
shows bolt
track.

GROWSPAN™ESTATE ELITE GREENHOUSES
18 Revision date: 01.01.16
ASSEMBLE THE FIRST GREENHOUSE SECTION
(CONTINUED)
5. Detach the diagonal brace of the sidewall frame at the
base rail location (if needed) and slip the upper end of
the brace over the long bolt installed earlier in Step 3.
6. With the upper end of the sidewall diagonal brace in
position, reattach the lower end to the base rail and
tighten both the upper and lower end bolts.
NOTE: View below shows the corner connection from
the outside of the frame.
7. Move to the sidewall base rail, slide a bolt into the bolt
track of the 1614 lower support (if needed), and secure
the support to the base rail.
A. Detach brace from this
connection (if needed).
Brace
Long
Bolt
B. Slide long bolt
into position.
C. Place upper
end of brace on
the long bolt and
add nut.
D. Slide the brace
and bolt up into the
slot of the gutter rail.
1632-4
1632-4
Brace
View (right)
shows the
frame assembly
up to this point.
View shows
the backside or
inside surface.
Side Wall
End
Wall
Inside the Frame
1630-4
1610
End Wall
Base Rail
Sidewall
Base Rail
View (left) shows
the same corner
from the outside.
End Wall
Base Rail
1610
1630-4

19
GROWSPAN™ESTATE ELITE GREENHOUSES
Revision date: 01.01.16
Assembled
Mid Rafter
ASSEMBLE THE FIRST GREENHOUSE SECTION
(CONTINUED)
8. Repeat the steps to secure the remaining sidewall
frame to the end wall frame.
NOTE: Circles indicate where to secure the sidewall
frame to the end wall as describe earlier.
9. Recheck all bolts to verify they are tight.
10. Brace the sidewalls so they stay in position and
continue by attaching the assembled mid rafter.
View shows
the backside or
inside surface.
Side Wall
ATTACH THE ASSEMBLED MID RAFTER
After installing the first two sidewall frames, attach the
assembled mid rafter to the frame as described below.
1. Place the assembled mid rafter in line with the frame as
shown.
ATTENTION: The bolt tracks of the lower 1614
supports must face up to attach the mid rafter to both
sidewall frames.
2. With assistance, lift the mid rafter into position
3. Align the bolt tracks of the rafter with the slots in the
gutter rail of the sidewall frame as shown.
4. Slide a bolt and nut into the bolt track of the mid rafter.
See the circles above. Use tape or slightly tighten the
nut to keep the bolt from sliding out of the track.
Slide bolt and nut
up into the bolt
track. See circles.
1632-4 Gutter Rail
Sidewall Base Rail
1630-4

GROWSPAN™ESTATE ELITE GREENHOUSES
20 Revision date: 01.01.16
Mid Rafter
Door End Wall
Sidewall
ATTACH THE ASSEMBLED MID RAFTER (CONTINUED)
5. Secure the rafter to the side wall using the bolts that
were installed earlier.
Slide bolt and
nut down into the
gutter rail slot.
NOTE: Dashed lines indicate the position of the gutter
rail, which is against the mid rafter bolt tracks.
6. Repeat the steps to attach the other mid rafter support
to the remaining sidewall frame.
Slide bolt
and nut
up into the
gutter rail
slot.
Mid Rafter
Gutter Rail of the
sidewall frame.
Secure
sidewall base
rail to the mid
rafter.
7. Verify that all bolts are tight.
NOTE: The assembled frame up to this point is shown
above.
8. Continue with the installation of the first ridge beam
(1650-4).
INSTALL THE RIDGE BEAM
Depending on the length of the greenhouse the ridge beam
(1650-4) may be shipped in two or three identical sections.
For this procedure, only one section is installed. The
remaining section or sections are installed as the frame
assembly continues.
IMPORTANT: Consult the ridge beam note on the next
page for box location of the ridge beam.
The parts required for this procedure include:
Part Number Quantity
16506 (bracket) 2
Hex-Head Bolts 8
Square-Head Bolts (short) 4
Nuts for square-head bolts 4
NOTE: These parts are found in the following box for the
selected greenhouse:
Greenhouse Sku Number Work from this open box:
104609 C/No. 7-3
104611 C/No. 9-3
Continue with the procedure on the following page to install
the ridge beam (1650-4).