Groz WOD-68 User manual

INSTRUCTION MANUAL S1570, Rev A
Waste Oil Drain
WOD-68
Congratulations on purchase of this World Class Waste Oil Drain!
Used/Waste Oil Drain with wheel mounted tank for gravity
draining of motor, engine, gearbox & differential oils,
transmissions & power steering fluids etc. from all type of
motor vehicles placed on an auto-lift or a pit.
Centrally mounted bowl is height adjustable & can be
optimally positioned allowing oil draining as well as other
operations
CONSTITUENTS
1. Tank fitted with Pressure Regulator & Safety Valve.
Assembled with 2 front swivel castors and discharge
hose
2. Bowl fitted with wire mesh screen
3. Drain Tube
4. Bowl Adjustment Tube Lock & Collar
5. Handle
6. Rear Rubber Wheels (2)
7. Wheel Fitment Kit comprising of 2 washers & 2 Circlips
8. PTFE Tape
2.Circlip Plier*1.HexKey*
TOOLS NEEDED TO ASSEMBLE THE UNIT
Bowl fitted
with wire mesh
Drain Tube
Bowl Adjustment
Tube Lock
Tank Closure Valve
Pressure Regulator
Tank
Front
Wheel
Collar
Rear Wheel
Spout Handle
Top Hose
Clamp
Discharge
Hose
doubles
as a level
indicator
Brass Valve
*not included *not included

ASSEMBLY INSTRUCTIONS
1. Open the Box in which the unit comes safely packed & remove
all parts. Be careful as some parts are small & maybe left un
noticed
2. Slide the 2 Rubber
Wheels onto the
Rear Wheel Shaft
at the bottom of the
tank. Now slide the
steel washer. Use a
circlip plier to install
the circlip. Repeat
the same for the
2nd wheel
3. Assemble the
Handle using a hex
key & position it as
required using the 2
hex bolts
4. The Tank is now ready & fully mobile
5. Take PTFE tape & apply it onto the threaded end of the drain
tube
6. Apply PTFE tape onto the threaded end of the Collar that fits
into the brass ball valve on top of the tank
7. Assemble the Collar
onto the Brass Valve
on top of the tank &
hand tighten
8. Fasten the threaded
end of the Drain Tube
into the bowl & hand
tighten
9. Open the Tank Closure
valve & now slide the
Drain tube fitted with
the Bowl through it
10. Adjust height as
per need & lock it in
place using the bowl
adjustment tube lock

OPERATION
1. Adjust the Bowl Height using the Bowl Adjustment Tube Lock
as required
2. Lock the Drain Tube firmly in place
3. Move the Waste Oil Drain under the drain plug , such that the
center of the bowl is almost exactly under the drain plug
4. Open the drain plug , allowing waste oil to drain under gravity
& get collected into the bowl
5. Bowl is connected to the Tank through the drain tube & waste
oil will start flowing into the tank
6. Waste Oil Level is indicated from the Discharge Hose
which doubles as a Level Indicator
7. Tank can be used for collection up to approx. 55 litres (14.5
gallons). At this point , oil level in the discharge hose will reach
the highest point almost close to the top hose clamp
8. To drain waste oil, loosen the Bowl Adjustment Tube lock &
remove the Drain Tube. It is very important to always raise
drain tube and close tank closure valve before emptying
9. Now Lock the Tank using the Tank Closure Valve
10. Insert the steel discharge spout at the end of the Hose into the
container in which waste oil is to be emptied
11. Take compressed air & connect it to the pressure regulator
fitted onto the tank. This is a tamper proof regulator set at
around 10-15 PSI (0.7-1 BAR). Note that pressure regulator
is fitted with a Safety Valve which will release air pressure in
case air pressure exceeds 20 PSI (1.4 BAR), thus acting as a
safety valve preventing possible damage to the tank
SPECIFICATIONS
WOD-68
Tank Capacity 68 Litres (18 Gallons)
Max. Collection Capacity 55 Litres (14.5 Gallons)
Bowl Capacity 10 Litres (10.5 Quarts)
Bowl Inner Diameter 14” ( 355 mm)
Length of Discharge Hose 2 metre
Maximum Adjustment Height 72” ( 1740 mm)
Minimum Height 34” (1135 mm)
Recommended Air Pressure 8 PSI (0.5 BAR)
Max. Air Pressure 150 PSI ( 10 BAR)
12. Within seconds , waste oil will flow out through the
discharge hose & empty the tank
13. Once waste oil is fully dispensed , disconnect the air
supply
14. Bottom of the Tank has a Drain plug which may
occasionally be opened to remove any sediments
collected at the bottom of the tank

Groz Engineering Tools (P) Ltd.
Groz Net Industries
Village Kherki Daula, National Highway-8
Gurgaon-122001, Haryana, INDIA
TEL [phone]
FAX [phone]
FAX (USA) +1.509.271.7848
FAX (UK) +44.870.121.1854
E-MAIL [email protected]
URL www.groz-tools.com
The Groz name, Groz logo and the mark are
trademarks of Groz Engineering Tools (P) Ltd. India
SPARE PARTS
PART NUMBER DESCRIPTION
CST/SW/WOD/68 Front Wheel castor Assembly (Set of 2)
WHL/WOD/68 Rear Back Rubber Wheels (Set of 2)
HOS/WOD/68 Discharge Hose complete with Steel Discharge Spout
PR/WOD/68 Pressure Regulator complete with Air Nipple & Pressure Relief Valve
• Never leave the unit unattended when operating or evacuating
• Never use near open flame or heat source
• Never use unit for handling volatile fuels & corrosive media
• Use only the nozzle assembly provided