Grundfos ALPHA2 15-55SF SS 115 User manual

GRUNDFOS INSTRUCTIONS
ALPHA2
Variable-speed circulators with AutoADAPT™
Installation and operating instructions
3191277
Listed
Conforms to ANSI/UL Std. 778
Certified to CAN/CSA Std. C22.2 No. 108

2
English (US)
English (US) Installation and operating instructions
Original installation and operating
instructions
These installation and operating instructions
describe Grundfos ALPHA2.
Sections 1-5 give the information necessary to
be able to unpack, install and start up the
product in a safe way.
Sections 6-11 give important information about
the product, as well as information on service,
fault finding and disposal of the product.
CONTENTS
Page
1. Limited warranty
Products manufactured by Grundfos Pumps
Corporation (Grundfos) are warranted to the
original user only to be free of defects in
material and workmanship for a period of 30
months from date of installation, but not more
than 36 months from date of manufacture.
Grundfos' liability under this warranty shall be
limited to repairing or replacing at Grundfos’
option, without charge, F.O.B. Grundfos’ factory
or authorized service station, any product of
Grundfos manufacture. Grundfos will not be
liable for any costs of removal, installation,
transportation, or any other charges that may
arise in connection with a warranty claim.
Products which are sold, but not manufactured
by Grundfos, are subject to the warranty
provided by the manufacturer of said products
and not by Grundfos' warranty.
Grundfos will not be liable for damage or wear to
products caused by abnormal operating
conditions, accident, abuse, misuse,
unauthorized alteration or repair, or if the
product was not installed in accordance with
Grundfos' printed installation and operating
instructions and accepted codes of good
practice. The warranty does not cover normal
wear and tear.
To obtain service under this warranty, the
defective product must be returned to the
distributor or dealer of Grundfos' products from
which it was purchased together with proof of
purchase and installation date, failure date and
supporting installation data. Unless otherwise
provided, the distributor or dealer will contact
Grundfos or an authorized service station for
instructions. Any defective product to be
returned to Grundfos or a service station must
1. Limited warranty 2
2. General information 3
2.1 Symbols used in this document 3
3. Receiving the product 4
3.1 Inspecting the product 4
3.2 Scope of delivery 4
4. Installing the product 4
4.1 Quick installation tips 5
4.2 Mechanical installation 5
4.3 Changing the power head position 6
4.4 Insulating the pump housing 7
4.5 Electrical connection 8
5. Starting up the product 10
5.1 Venting the pump 10
5.2 First startup 10
6. Product introduction 10
6.1 Product description 10
6.2 Applications 10
6.3 Pumped liquids 11
7. Identification 12
7.1 Nameplate 12
7.2 Type key 12
7.3 Approvals 12
8. Control functions 13
8.1 Elements on the control panel 13
8.2 Display 13
8.3 Setting the pump 13
8.4 Selection of control mode by
application 13
8.5 Pump control 14
8.6 Pump performance and operating
mode selection 15
9. Fault finding the product 16
10. Technical data 18
10.1 Operating conditions 18
11. Disposing of the product 19
Prior to installation, read this
document. Installation and operation
must comply with local regulations
and accepted codes of good practice.
This appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or lack
of experience and knowledge if they
have been given supervision or
instruction concerning the use of the
appliance in a safe way and
understand the hazards involved.
Children must not use or play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
Successful operation depends on
careful attention to the procedures
described in this manual. Keep this
manual for future use.

3
English (US)
be sent freight prepaid; documentation
supporting the warranty claim and/or a Return
Material Authorization must be included if so
instructed.
Grundfos will not be liable for any incidental or
consequential damages, losses, or expenses
arising from installation, use, or any other
causes. There are no express or implied
warranties, including merchantability or fitness
for a particular purpose, which extend beyond
those warranties described or referred to above.
Some jurisdictions do not allow the exclusion or
limitation of incidental or consequential
damages and some jurisdictions do not allow
limitations on how long implied warranties may
last. Therefore, the above limitations or
exclusions may not apply to you. This warranty
gives you specific legal rights and you may also
have other rights which vary from jurisdiction to
jurisdiction.
Products which are repaired or replaced by
Grundfos or authorized service center under the
provisions of these limited warranty terms will
continue to be covered by Grundfos warranty
only through the remainder of the original
warranty period set forth by the original
purchase date.
2. General information
2.1 Symbols used in this document
The text accompanying the three hazard
symbols DANGER, WARNING and CAUTION
will be structured in the following way:
Example
DANGER
Indicates a hazardous situation which,
if not avoided, will result in death or
serious personal injury.
WARNING
Indicates a hazardous situation which,
if not avoided, could result in death or
serious personal injury.
CAUTION
Indicates a hazardous situation which,
if not avoided, could result in minor or
moderate personal injury.
SIGNAL WORD
Description of hazard
Consequence of ignoring the warning.
- Action to avoid the hazard.
DANGER
Electric shock
Death or serious personal injury.
- Switch off the power supply before
starting any work on the product.
Make sure that the power supply
cannot be accidentally switched on.
A blue or grey circle with a white
graphical symbol indicates that an
action must be taken to avoid a
hazard.
A red or grey circle with a diagonal
bar, possibly with a black graphical
symbol, indicates that an action must
not be taken or must be stopped.
If these instructions are not observed,
it may result in malfunction or damage
to the equipment.
Notes or instructions that make the
work easier and ensure safe
operation.

4
English (US)
3. Receiving the product
3.1 Inspecting the product
Check that the product received is in
accordance with the order.
Check that the voltage and frequency of the
product match voltage and frequency of the
installation site. See section 7. Identification for
information on the nameplate.
3.2 Scope of delivery
The box contains the following items:
• one Grundfos ALPHA2 pump
• one insulation shell
• one line cord or terminal box
• two gaskets
• installation and operating instructions
• one check valve
• one "Check Valve Installed" sticker.
4. Installing the product
WARNING
Pressurized system
Death or serious personal injury.
- Before dismantling the pump, drain
the system or close the isolating
valve on either side of the pump
before the screws are removed.
The pumped liquid may be scalding
hot and under high pressure.
DANGER
Electric shock
Death or serious personal injury.
- Switch off the power supply before
starting any work on the product.
Make sure that the power supply
cannot be accidentally switched on.
DANGER
Electric shock
Death or serious personal injury.
- This pump has not been
investigated for use in swimming
pool or marine areas.

5
English (US)
4.1 Quick installation tips
1. To ensure proper air venting of your system,
place the pump in "Fixed Speed III" mode
until all air has been removed. Isolating
zones during this process will ensure proper
air removal.
2. For balancing manifold zone(s) applications,
utilizing "Constant Pressure mode 1 or 2"
and only one zone at a time during balancing
will ensure proper flow rate to each zone.
3. Always review your boiler minimum flow rate
requirements if utilizing the pump as a
primary pump. Select one of the fixed speed
modes for boiler primary pump applications.
4. In general, for maximum energy savings and
comfort level, start with the AUTOADAPT™
mode.
5. You may change hydraulic selection while
pumping. No permanent damage will occur.
In fact, Grundfos encourages testing the
various hydraulic modes with your hydronic
system to ensure maximum energy savings
and comfort level.
6. With zone panel control applications, when
there is a call for heat and power has been
sent to the pump, the pump will remember
and restart from the last duty point and
hydraulic mode.
4.2 Mechanical installation
When making pipe connections, follow the
piping manufacturer's recommendations and all
code requirements for the piping material.
• Flush the system of debris before
installation.
• Insert the check valve if required. See fig. 1.
• Refer to the arrows on the pump housing
indicating the direction of the liquid flow
through the pump.
• Install the pump with horizontal motor shaft.
See fig. 2.
• Fit the two gaskets supplied to the pump
ends.
Fig. 1 Check valve installation
Fig. 2 Installation positions
TM04 3422 4408
TM04 3417 4408
UL

6
English (US)
4.3 Changing the power head position
• Make any change to the power head
orientation before filling the system with
liquid. You can turn the power head in steps
of 90 °.
• See fig. 3 for permissible positions.
• Only use orientations C and D for CSA,
enclosure type 2.
Proceed as follows:
1. If liquid is present, drain the liquid from the
pump or isolate the liquid from the pump.
2. Remove the four socket head cap screws.
3. Turn the pump head to the desired position.
See fig. 3.
4. Cross-tighten the screws to: 7 ft-lbs torque.
Fig. 3 Changing the power head position
Fig. 4 Remove the four socket head cap
screws on the power head to
change the power head position
CAUTION
Hot surface
Minor or moderate personal injury.
- Position the pump so that persons
cannot accidentally come into
contact with hot surfaces.
DANGER
Electric shock
Death or serious personal injury.
- Switch off the power supply before
starting any work on the product.
Make sure that the power supply
cannot be accidentally switched on.
WARNING
Pressurized system
Death or serious personal injury.
- Before dismantling the pump, drain
the system or close the isolating
valve on either side of the pump
before you remove the screws. The
pumped liquid may be scalding hot
and under high pressure.
If you change the position of the
power head, fill the system with the
liquid to be pumped or open the
isolating valves.
TM04 3418 1010
TM06 7559 3616
Power head
orientation A
Power head
orientation B
Power head
orientation C
Power head
orientation D

7
English (US)
4.4 Insulating the pump housing
Fig. 5 Insulating the pump housing
You can reduce the heat loss from the pump and
pipes by insulating the pump housing and the
pipes. See figures 5 and 6.
• Insulating shells are supplied with ALPHA2
cast iron flanged versions. See fig. 6.
• For pumps in air-conditioning and cooling
systems (down to +14 °F (-10 °C)), it is
required to apply a silicon sealant to the
internal contours of the shell in order to
eliminate any air gaps and prevent
condensation between the insulating shell
and pump housing. Alternatively, you can
insulate the pump manually in accordance
with standard insulating requirements for
heating and cooling systems.
• The fitting of insulating shells will increase
the pump dimensions.
Fig. 6 Fitting insulating shells to the pump
TM06 7711 3816
Limit the heat loss from the pump
housing and pipes.
Do not insulate the control box or
cover the control panel.
TM06 7589 4716TM06 7588 3516

8
English (US)
4.5 Electrical connection
• The motor is protected by the electronics in
the control box and requires no external
motor protection.
• Check that the supply voltage and frequency
correspond to the values stated on the
pump.
• Only connect the pump to the power supply
with the line cord or through the terminal box
supplied with the pump; see sections
4.5.1 For pump models with line cord and
4.5.2 For pump models with terminal box.
• Do not modify and only use the line cord
supplied.
• The lights on the control panel indicate that
the electrical supply has been switched on.
4.5.1 For pump models with line cord
Follow the procedure as shown in fig. 7.
Fig. 7 Connecting and removing the power
plug for line cord models
DANGER
Electric shock
Death or serious personal injury.
- All electrical work must be carried
out by a qualified electrician in
accordance with the latest edition
of the National Electric Code and
state, local codes and regulations.
DANGER
Electric shock
Death or serious personal injury.
- Switch off the power supply before
starting any work on the product.
Make sure that the power supply
cannot accidentally switched on.
DANGER
Electric shock
Death or serious personal injury.
- This pump has not been
investigated for use in swimming
pool or marine areas.
DANGER
Electric shock
Death or serious personal injury.
- This pump is supplied with a
grounding conductor and
grounding-type attachment plug. To
reduce the risk of electric shock, be
certain that it is connected only to a
properly grounded, grounding-type
receptacle in accordance with the
National Electric Code and any
state, local governing codes and
regulations.
TM04 3420 1010
1
2
3
How to remove the cord plug from the
pump (bottom view):
How to insert the line cord plug onto the
pump (side view):
1. Insert a 1/8 in. flat blade
screwdriver into the slot.
2. Twist the screwdriver.
3. Pull the cord to remove it.

9
English (US)
4.5.2 For pump models with terminal box
1. Loosen the terminal box screw from the
terminal box cover.
2. Utilize either conduit port for the wiring
entrance.
3. Wirethe plug connector as illustrated in the
section Wiring procedure below, steps 3a-
3d. Then complete steps 4-7.
Wiring procedure
4. Slide the terminal box cover over the
terminal box body.
5. Tighten the cross-head screw on the terminal
box to 5 in-lbs.
6. Switch on the power supply.
7. The lights on the control panel will then
indicate that the power supply has been
switched on.
Be sure to connect the ground cable
conductor (green) of the pump to the
ground cable conductor of the power
supply.
Step Action Illustration
3a Strip the ends of the cable conductors as
illustrated.
TM06 8250 4816
3b
Align the end of each of the pump's cable
conductors, including any frayed strands,
with the end of the corresponding cable
conductor from the power supply.
Green conductor: ground
Black conductor: line
White conductor: neutral
TM06 8253 4816
3c
Insert the ends of the cable conductors
into the connector.
Push the cable conductors fully into the
connector.
TM06 8251 4816
3-d Twist the connector until you see two
twists in the cable conductors.
TM06 8252 4816
0.4 in.
(10 mm)
Cable conductor
from the pump
Cable conductor
from the power
supply

10
English (US)
5. Starting up the product
The required minimum inlet pressure must be
available at the pump inlet.
5.1 Venting the pump
The pump is self-venting. It need not be vented
before startup.
Air in the pump may cause noise. This noise
ceases after a few minutes running.
You obtain quick venting of the pump by setting
the pump to speed III for a short period. How
fast the pump is vented depends on the system
size and design.
When you have vented the pump, i.e. when the
noise has ceased, set the pump according to the
recommendations. See section 8.3 Setting the
pump.
You cannot vent the system through the pump.
5.2 First startup
• The light in the control panel shows that the
power supply has been switched on. See
fig. 9.
• Factory setting: AUTOADAPT.
6. Product introduction
6.1 Product description
The ALPHA2 circulator pump incorporates a
permanent-magnet motor and differential-
pressure control enabling continuous
adjustment of the pump performance to the
actual system requirements.
The pump has a user-friendly front-mounted
control panel. See sections 7. Identification and
8. Control functions.
When you install an ALPHA2, it means:
• Easy installation and start-up.
– The pump is easy to install.
Thanks to the AUTOADAPT function
(factory setting), you can start the pump,
in most cases, without making any
settings.
• High degree of comfort.
• Minimum noise from valves, etc.
• Low energy consumption.
– Low energy consumption compared to
conventional circulator pumps.
6.2 Applications
The ALPHA2 circulator pump is designed for the
circulation of water in heating systems, domestic
hot-water systems as well as air-conditioning
and cold-water systems.
Cold-water systems are defined as systems
where the ambient temperature is higher than
the temperature of the pumped liquid.
The pump is the best choice for the following
systems:
• underfloor heating systems
• one-pipe systems
• two-pipe systems.
The pump is suitable for the following:
• systems with constant or variable flows
where you want to optimize the setting of the
pump duty point.
• systems with variable flow-pipe temperature.
• balancing of domestic heating systems.
Do not start the pump until the system
has been filled with liquid and vented.
The pump must not run dry.
DANGER
Explosion hazard
Death or serious personal injury.
- Do not use the pump for transfer of
flammable liquids such as diesel
oil, gasoline, and similar liquids.
DANGER
Electric shock
Death or serious personal injury.
- This pump has not been
investigated for use in swimming
pool or marine areas.

11
English (US)
6.3 Pumped liquids
For information about pressures and
temperatures, see section 10. Technical data.
In heating systems, the water must meet the
requirements of accepted standards on water
quality in heating systems.
The pump is suitable for the following liquids:
• Thin, clean, non-aggressive and non-
explosive liquids, not containing solid
particles or fibers.
• Cooling liquids, not containing mineral oil.
• Domestic hot water
Maximum: 14 °dH
Maximum: 149 °F (65 °C)
Maximum peak: 158 °F (70 °C).
For water with a higher degree of hardness,
contact Grundfos.
• Softened water.
The kinematic viscosity of water is 1 mm2/s (1
cSt) at 68 °F (20 °C). If the pump is used for a
liquid with a higher viscosity, the hydraulic
performance of the pump will be reduced.
Example: 50 % glycol at 68 °F (20 °C) means a
viscosity of approximately 10 mm2/s (10 cSt)
and a reduction of the pump performance by
approximately 15 %.
Do not use additives that can or will disturb the
functionality of the pump.
When selecting a pump, take the viscosity of the
pumped liquid into consideration.
For technical data, see section 10. Technical
data.
6.3.1 Glycol
The pump is designed for pumping clean water,
or up to 50/50 mixtures by weight of glycol and
water.
For glycol usage as well as additional liquid
information, see section 10. Technical data.
To prevent the glycol mixture from degrading,
avoid temperatures exceeding the rated liquid
temperature and minimize the operating time at
high temperatures.
It is important to clean and flush the system
before adding the glycol mixture.
To prevent corrosion or precipitation, check the
glycol mixture and maintain it regularly. If further
dilution of the supplied glycol is required, follow
the glycol supplier's instructions.
CAUTION
Flammable material
Minor or moderate personal injury.
- Do not use the pump for flammable
liquids, such as diesel oil and
petrol.
WARNING
Biological hazard
Death or serious personal injury.
- In domestic hot-water systems, the
temperature of the pumped liquid
must always be above 122 °F (50
°C) due to the risk of legionella.
WARNING
Biological hazard
Death or serious personal injury.
- In domestic hot-water systems, the
pump is permanently connected to
the mains water. Therefore, do not
connect the pump by a hose.
CAUTION
Corrosive substance
Minor or moderate personal injury.
- Do not use the pump for aggressive
liquids, such as acids and
seawater.

12
English (US)
7. Identification
7.1 Nameplate
Fig. 8 Nameplate
7.2 Type key
7.3 Approvals
FCC sections
Section 15.19 (a) 3
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
Section 15.21
Any changes or modifications to this equipment
not expressly approved by the party responsible
for compliance could void the user's authority to
operate this equipment void.
Section 15.105 (b)
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment to an outlet on a
circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
Canadian EMC Standard: ICES-003
This class B digital apparatus complies with
Canadian ICES-003.
TM04 3419 3516
Pos. Description
1 Product number
2 Voltage [V]
3
Rated current [A]:
• Min.: Minimum current [A]
• Max.: Maximum current [A]
4
Input power [W]:
• Min.: Minimum power [W]
• Max.: Maximum power [W]
5 Maximum fluid temperature [°F]
Example ALPHA2 15 -55 - 165
Pump type
Nominal diameter (DN) of inlet
and outlet ports [mm]
Maximum head [dm]
: Cast-iron pump housing
N: Stainless-steel pump housing
Port-to-port length [mm]
This equipment has been tested and
found to comply with the limits for a
class B digital device, pursuant to Part
15 of the FCC Rules.
3191277
Listed

13
English (US)
8. Control functions
8.1 Elements on the control panel
Fig. 9 Control panel
8.2 Display
The display (1) is on when you have switched on
the power supply.
The display shows the actual pump power
consumption in watt (integer) or the actual flow
during operation.
If a fault is indicated, correct the fault and reset
the pump by switching the power supply off and
on.
If the pump impeller is rotated, for example
when filling the pump with water, sufficient
energy can be generated to light up the display
even if the power supply has been switched off.
Light field indicating high and low flow
• The light field blinks for low flow
– If the flow is lower than 1 gpm, the light
field alternately flashes between "0" and
"1" randomly.
• The light field shows HI for high flow
– If the flow is higher than 12 gpm, the light
field shows "HI" on user interface.
8.2.1 Light fields indicating the pump setting
The pump has optional performance settings
which you can select with the push-button. See
fig. 9.
The pump setting is indicated by light fields in
the display. See fig. 10.
Fig. 10 Light fields
For more information about the function of the
settings, see section 9. Fault finding the product.
8.3 Setting the pump
You can change the pump setting by pressing
the push-button.
8.3.1 Factory default setting
The pump's factory default setting is the
AUTOADAPT setting.
8.3.2 Changing from recommended to
alternative pump setting
Heating systems are "slow" systems that cannot
be set to the optimum operation within minutes
or hours.
However, if the recommended pump setting in
some applications does not give the desired
distribution of heat in the rooms of the house,
you can change to an alternative pump setting.
8.4 Selection of control mode by
application
See also sections 8. Control functions and
8.6 Pump performance and operating mode
selection.
TM04 3421 3511
Pos. Description
1Display showing the power
consumption in watt or the flow.
Light field indicating high and low flow
2 Production code:
• 1st and 2nd figures: year
• 3rd and 4th figures: week
3 Light field indicating fixed speed
4 Light field indicating constant pressure
5 Light field indicating AUTOADAPT
6Push-button for selection of pump
setting
TM06 7517 3516
Application Control mode
Floor heating Constant pressure
Two-pipe system AUTOADAPT
Ventilation Speed 1, 2 or 3
Boiler-shunt Speed 1, 2 or 3
One-pipe system Speed 1, 2 or 3 or
constant pressure
Domestic hot water Speed 1, 2 or 3

14
English (US)
8.5 Pump control
See section 8.6 Pump performance and
operating mode selection.
AUTOADAPT, underfloor heating and two-pipe
heating systems
The AUTOADAPT function adjusts the pump
performance to the actual heat demand in the
system. As the performance is adjusted
gradually, we recommend that you leave the
pump in the AUTOADAPT mode at least one
week before changing the pump setting.
If you choose to change back to AUTOADAPT,
the pump remembers its last setpoint in
AUTOADAPT and resumes the automatic
adjustment of the performance.
Constant-pressure control
In this control mode, a constant differential
pressure across the pump is maintained,
irrespective of the flow.
See also sections 8. Control functions and
8.3 Setting the pump.
Constant speed control (III, II, or I)
In this control mode, the pump runs at a
constant speed and consequently on a constant
curve.
• In speed III, the pump is set on the maximum
curve under all operating conditions. You can
quickly vent the pump by setting the pump to
speed III for a short period.
• In speed II, the pump is set on the medium
curve under all operating conditions.
• In speed I, the pump is set on the minimum
curve under all operating conditions.
Manual summer mode
In manual summer mode, the pump is stopped
to save energy and only the electronics are
running. To avoid lime deposit that could block
the pump, the pump is started every 24 hours for
two minutes at a low speed. This is an
alternative to shutting down the pump if there is
a risk of lime deposit.
The display is turned off. If any faults occur
during manual summer mode, the display will
show the faults when the pump is taken out of
manual summer mode.
If any alarms occur during manual summer
mode, no alarms will be shown. When manual
summer mode is deactivated again, only the
actual alarms will be displayed.
• To activate manual summer mode, press and
hold the push-button for three seconds. All
light fields will turn off, and the pump will
stop. The AUTOADAPT light field will flash for
four seconds.
• To deactivate manual summer mode, press
the push-button to return to normal
operation.

15
English (US)
8.6 Pump performance and operating mode selection
The hydraulic performance shown is without check valve.
TM06 7506 3516
AUTOADAPT
Operating range
(maximum to minimum)
Pos. Description
• Push-button for selection of pump setting
• Every time you press the push-button, the circulator setting is changed.
III
High constant speed
• The pump runs at a constant speed and consequently on a constant curve. In speed
III, the pump is set on the maximum curve under all operating conditions. You obtain
quick vent of the pump by setting the pump to speed III for a short period.
II
Medium constant speed
• The pump runs at a constant speed and consequently on a constant curve. In speed II,
the pump is set on the medium curve under all operating conditions.
I
Low constant speed
• The pump runs at a constant speed and consequently on a constant curve. In speed I,
the pump is set on the minimum curve under all operating conditions.
Constant pressure I
• The duty point of the pump will move left and right along the lowest constant-pressure
curve depending on the water demand in the system. The head is kept constant,
irrespective of the water demand.
Constant pressure II
• The duty point of the pump will move left and right along the middle constant-pressure
curve depending on the water demand in the system. The head is kept constant,
irrespective of the water demand.
Constant pressure III
• The duty point of the pump will move left and right along the highest constant-pressure
curve depending on the water demand in the system. The head is kept constant,
irrespective of the water demand.
AUTOADAPT (factory setting)
• This function controls the pump performance automatically within the defined
performance range (shaded area). AUTOADAPT will adjust the pump performance to
system demands over time.
(Hold for
3 sec.)
Manual summer mode
The pump is stopped to save energy, and only the electronics are running. To avoid
liming and blocking of the pump, the pump is started every 24 hours for two minutes at a
low speed.

16
English (US)
9. Fault finding the product
DANGER
Electric shock
Death or serious personal injury.
- Switch off the power supply before
starting any work on the product.
Make sure that the power supply
cannot be accidentally be switched
on.
WARNING
Pressurized system
Death or serious personal injury.
- Before dismantling the pump, drain
the system or close the isolating
valve on either side of the pump
before the screws are removed. The
pumped liquid may be scalding hot
and under high pressure.
Fault Control panel Remedy
1. The pump
does not
run.
Light field is off. a) The pump is not
connected to the
power supply.
Connect the pump to the power
supply.
b) The circuit breaker
has tripped. Cut in the circuit breaker.
c) The pump is
defective. Replace the pump.
Light field is on. a) Supply voltage is too
high.
Check that the power supply falls
within the specified range.
b) The rotor is blocked
by impurities. Remove the impurities.
"___ ___" a) Supply voltage is too
low.
Switch the power off and on.
Check for air, locked rotor and/or
voltage.
Correct the power supply.
2. Noise in
the system
Light field is on. a) There is air in the
system. Install an air eliminator.
b) The flow is too high. Reduce the pump speed.
c) Thermal expansion
of system
components.
Check the mounting brackets for
the pipes.
Secure loose mounting brackets.
3. Noise in
the pump
Light field is on. a) There is air in the
pump.
Let the pump run, as it will vent
over time.
Install an air eliminator.
b) The inlet pressure is
too low.
Increase the inlet pressure.
Check the air volume in the
expansion tank, if this is installed.
(Pressure leaks in the system can
lead to cavitation.)
c) No liquid (dry
running).
Ensure the system has been filled
with liquid and vented.
Open the isolating valves.
d) The pump is
defective.
Replace the pump.

17
English (US)
4. Insufficient
heat
Light field is on. a) The pump
performance is set
too low.
Increase the pump speed or
constant pressure.
b) The thermostat is set
too low or is not
working.
Check to see if the circulator is in
the proper operating mode.
Check the thermostat to ensure
that it is set to the desired
temperature and is working.
Replace the batteries in the
thermostat.
c) Air or gas in the
system.
Vent the air or gas from the system
by allowing the pump to run, as it
will vent over time.
Install an air eliminator.
If necessary rework the piping.
d) The valves are
sticking.
Make sure all valves are in good
working order, i.e. remove lime
deposits.
e) Wrong direction of
flow.
See the direction of flow arrow
marked on the pump.
Reinstall the pump to correct the
direction of flow.
f) The boiler is not
working properly.
Check the water temperature from
the boiler and check the boiler
functions.
Repair the boiler if required.
g) The pump
performance is not
adequate for the
application.
Check for proper sizing of the
circulator and other system
components.
h) The pump
performance is not
adequate for the
application.
Check the T calculation.
Fault Control panel Remedy

18
English (US)
10. Technical data
10.1 Operating conditions
Supply voltage
1 x 115 V, + 10 %/- 10 %, 60 Hz.
Motor protection
The pump requires no external motor protection.
Enclosure class
Indoor use only, IP42.
CSA enclosure type 2.
Insulation class
F.
Relative humidity
Maximum 95 %.
Maximum outlet pressure
150 psi (10.34 bar).
Inlet pressure
Sound pressure level
43 dB (A).
Ambient temperature
32 °F (0 °C) to 104 °F (40 °C).
Liquid temperature
36 °F (2 °C) to 230 °F (110 °C).
To avoid condensation in the control box and
stator, the liquid temperature must always be
higher than the ambient temperature.
Glycol
Maximum glycol concentrations with clean
water:
50 % glycol @ 36 °F (2 °C).
Hydraulic performance change can be expected.
Watt readings
Accuracy: ± 1 watt.
Flow indicator
Provides a relative indication of flow – should
not be used in lieu of a flow meter.
Check valve
Use of a check valve may reduce pump
hydraulic performance (up to - 10 %).
Use a check valve in parallel pumping
applications.
Curve conditions
Test liquid: Airless water.
Curves apply to a density of 983.2 kg/m3 and a
liquid temperature of 140 °F (60 °C).
All curves show average values and should not
be used as guarantee curves. If a specific
minimum performance is required, individual
measurements must be made.
Curves apply to a kinematic viscosity of 0.474
cSt.
Approximate power usage
Liquid
temperature
Minimum
inlet pressure
167 °F (75 °C) 0.75 psi (0.05 bar)
194 °F (90 °C) 4.06 psi (0.28 bar)
230 °F (110 °C) 15.7 psi (1.08 bar)
Ambient
temperature
[°F (°C)]
Liquid temperature
Minimum
[°F (°C)]
Maximum
[°F (°C)]
32 °F
(0 °C)
36 °F
(2 °C)
230 °F
(110 °C)
50 °F
(10 °C)
50 °F
(10 °C)
230 °F
(110 °C)
68 °F
(20 °C)
68 °F
(20 °C)
230 °F
(110 °C)
86 °F
(30 °C)
86 °F
(30 °C)
230 °F
(110 °C)
95 °F
(35 °C)
95 °F
(35 °C)
194 °F
(90 °C)
104 °F
(40 °C)
104 °F
(40 °C)
158 °F
(70 °C)
In domestic hot water systems, keep
the liquid temperature below 149 °F
(65 °C) to eliminate the risk of lime
precipitation.
Speed
setting Minimum Maximum
High
constant
speed
III 39 W 45 W
Medium
constant
speed
II 15 W 30 W
Low
constant
speed
I5 W 8 W
Constant
pressure 8 W 45 W
Constant
pressure 14 W 45 W
Constant
pressure 22 W 45 W
AUTOADAPT 5 W 45 W

19
English (US)
11. Disposing of the product
This product or parts of it must be disposed of in
an environmentally sound way:
1. Use the public or private waste collection
service.
2. If this is not possible, contact the nearest
Grundfos company or service workshop.

20