Grundfos JPA Series User manual

JPA, JPC, JPD PT
Pumps and boosters
Installation and operating instructions
GRUNDFOS INSTRUCTIONS

English (GB)
2
English (GB) Installation and operating instructions
Original installation and operating instructions
These installation and operating instructions
describe Grundfos JPC, JPA and JPD pumps.
Sections 1-3 give the information necessary to be
able to unpack, install and start up the product in a
safe way.
Sections 4-8 give important information about the
product, as well as information on service, fault
finding and disposal of the product.
CONTENTS
Page
1. General information
1.1 Symbols used in this document
The text accompanying the three hazard symbols
DANGER, WARNING and CAUTION is structured in
the following way:
1. General information 2
1.1 Symbols used in this document 2
2. Installing the product 3
2.1 Checking the product prior to installation 3
2.2 Location 3
2.3 Mechanical installation 3
2.4 Electrical connection 5
3. Starting up the product 6
3.1 Priming the pump 6
3.2 Shaft seal run-in 6
4. Product introduction 7
4.1 JPA JPC 7
4.2 JPA PM, JPC PM, JPA PT, JPC PT 7
4.3 JPD PT 7
4.4 Identification 8
5. Servicing the product 9
5.1 Maintaining the product 9
5.2 Spare parts and kits 9
6. Fault finding 10
7. Technical data 11
8. Disposing of the product 12
Read this document and the quick guide
before installing the product. Installation
and operation must comply with local
regulations and accepted codes of good
practice.
This appliance can be used by children
aged from 8 years and above and by
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use
of the appliance in a safe way and
understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not
be made by children without supervision.
Make sure that the system in which the
pump is incorporated is designed for the
maximum pump pressure.
This pump has been evaluated for use with
water only.
DANGER
Indicates a hazardous situation which, if
not avoided, will result in death or serious
personal injury.
WARNING
Indicates a hazardous situation which, if
not avoided, could result in death or
serious personal injury.
CAUTION
Indicates a hazardous situation which, if
not avoided, could result in minor or
moderate personal injury.
SIGNAL WORD
Description of hazard
Consequence of ignoring the warning.
- Action to avoid the hazard.
A blue or grey circle with a white graphical
symbol indicates that an action must be
taken.
A red or grey circle with a diagonal bar,
possibly with a black graphical symbol,
indicates that an action must not be taken
or must be stopped.
Tips and advice that make the work easier.
If these instructions are not observed, it
may result in malfunction or damage to the
equipment.

English (GB)
3
2. Installing the product
2.1 Checking the product prior to
installation
Check that the rotating parts turn freely. Position
numbers refer to fig. 1.
1. Remove the fan cover (13) from the motor.
2. Insert a screwdriver in the notch on the motor
shaft.
3. If the rotor is blocked, turn the screwdriver,
tapping it gently with a hammer.
Fig. 1 Checking the rotating parts
2.2 Location
Install the pump in a well-ventilated location,
protected from rain, snow and direct sunlight. The
ambient temperature must not exceed 35 or 55 °C.
See the nameplate.
Fig. 2 Weather conditions
We recommend that you place the pump as close as
possible to the liquid to be pumped.
2.2.1 Frost protection
If the pump is not used during periods of frost, it
must be drained to avoid damage.
Remove the drain plug to drain the pump. See fig. 3.
Fig. 3 Draining the pump
2.3 Mechanical installation
2.3.1 Positioning the product
Install the pump in horizontal position.
Install the pump so that it is not stressed by the
pipes.
We recommend that you fasten the pump to the
foundation and use pipe hangers, thus ensuring that
vibrations caused by pump operation are absorbed.
See fig. 4.
Fig. 4 Fastening the pump and the pipes
Observe local regulations concerning
limits for manual lifting or handling.
CAUTION
Crushing of feet
Minor or moderate personal injury
- Use safety shoes when handling the
pump.
TM06 4529 2515TM06 4530 2515
TM06 8026 4516TM06 8024 4216
Max. 8 m / 26 ft
0/Off
1/On
ãPIW

English (GB)
4
2.3.2 Pipe connection
If the inlet pipe is longer than 10 m or the suction lift
is greater than 4 m, the diameter of the pipe must be
larger than 1". If a hose is used as inlet pipe, it must
be non-collapsible.
To prevent solids from entering the pump, you can fit
a filter to the inlet pipe. We recommend that you fit a
foot valve on the inlet side.
For suction lifts of over 4 m or for long horizontal
stretches, we recommend that you use an inlet pipe
with a diameter larger than the inlet opening of the
pump.
Fig. 5 Inlet pipe sloping upwards
2.3.3 JPD deep-well installation
A JPD must have the ejector installed in the well.
This means that two pipes are needed for the suction
installation.
Fig. 6 JPD PT installation
The internal diameters of the pipes must
never be smaller than that of the openings
of the pump.
To prevent formation of air pockets, the
inlet pipe must slope slightly upwards
towards the pump. See fig. 5.
TM06 4532 2515
TM06 5436 4615
up to 27m
FP")
Up to 27 m
≥10 cm (4")

English (GB)
5
2.4 Electrical connection
Carry out the electrical connection according to local
regulations.
Check that the supply voltage and frequency
correspond to the values stated on the nameplate
and that it is possible to make a good earth
connection.
Single-phase motors incorporate a thermal switch
and require no additional motor protection.
2.4.1 Wiring diagram
Fig. 7 1-phase pumps
DANGER
Electric shock
Death or serious personal injury
- Before starting any work on the product,
make sure that the power supply has
been switched off and that it cannot be
accidentally switched on.
DANGER
Electric shock
Death or serious personal injury
- The protective earth of the socket outlet
must be connected to the protective
earth of the pump. The plug must
therefore have the same PE connection
system as that of the socket outlet. If
not, use a suitable adapter.
We recommend that you fit the permanent
installation with a residual-current circuit
breaker (RCCB) with a tripping current
less than 30 mA.
DANGER
Electric shock
Death or serious personal injury
- If the pump is used for cleaning or
maintenance of swimming pools,
garden ponds or similar places, make
sure that the pump is supplied through a
residual-current circuit breaker, RCCB,
with a rated residual operating current
of 30 mA.
DANGER
Electric shock
Death or serious personal injury
- Power supply cables without a plug
must be connected to a supply
disconnecting device incorporated in
the fixed wiring according to the local
wiring rules.
DANGER
Electric shock
Death or serious personal injury
- The pump must be earthed.
TM06 3322 5015

English (GB)
6
3. Starting up the product
3.1 Priming the pump
1. Remove the priming plug. See fig. 8.
2. Fill the pump with water.
3. Refit the priming plug and tighten by hand.
The pump can now be started.
Fig. 8 Priming the pump
If there is a suction lift, up to five minutes may pass
from the moment the pump is started until it delivers
water. This period depends on the length and
diameter of the inlet pipe.
3.2 Shaft seal run-in
The seal faces are lubricated by the pumped liquid,
meaning that there may be a certain amount of
leakage from the shaft seal.
When the pump is started up for the first time, or
when a new shaft seal has been installed, a certain
run-in period is required before the leakage is
reduced to an acceptable level. The time required for
this depends on the operating conditions, i.e. every
time the operating conditions change, a new run-in
period will be started.
Under normal conditions, the leaking liquid will
evaporate. As a result, no leakage will be detected.
WARNING
Flammable material
Death or serious personal injury
- Do not use the pump for flammable
liquids, such as diesel oil, petrol or
similar liquids.
CAUTION
Impurities in water
Minor or moderate personal injury
- Flush the system with clean water to
remove all impurities before you start
the pump.
CAUTION
Hot surface
Minor or moderate personal injury
- Do not run pump continuously with a
closed inlet or outlet valve.
WARNING
Corrosive substance
Death or serious personal injury
- Do not use the pump for aggressive
liquids.
CAUTION
Hot or cold liquid
Minor or moderate personal injury
- Make sure that the escaping hot or cold
liquid does not cause injury to persons
or damage to the equipment.
CAUTION
Hot surface
Minor or moderate personal injury
- Use protective gloves if the liquid or
ambient temperature is higher than
40 °C.
DANGER
Electric shock
Death or serious personal injury
- Do not use the pump in swimming
pools, garden ponds or similar places if
there are people in the water.
Do not start the pump until it has been
filled with liquid.
The pump must not be started more than
20 times per hour.
The pump must not run without delivering
water for more than five minutes.
TM06 8025 4516
Do not start the pump until it has been
filled with liquid.

English (GB)
7
4. Product introduction
4.1 JPA JPC
JPA and JPC pumps are horizontal, self-priming
centrifugal pumps.
JPA pumps are made of cast iron, and the JPC
pumps are made of a composite material.
The pumps are designed for pumping water and
other thin, non-aggressive and non-explosive liquids,
not containing solid particles or fibres.
The pumps are especially suited for use in
small-scale agriculture and gardening.
The pumps can be permanently connected to the
water mains or connected to a hose set.
Fig. 9 JPA pumps
Fig. 10 JPC pump
4.2 JPA PM, JPC PM, JPA PT, JPC PT
JPA PM and JPC PM are compact boosters
consisting of a JPA pump and a Grundfos Pressure
Manager (PM 1 version). To reduce the number of
starts and stops, an external tank can be installed.
JPA PT and JPC PT are boosters consisting of a
pump, a pressure switch, a pressure gauge and a
diaphragm tank. The pressure switch automatically
starts the pump according to demand. The
diaphragm tank ensures a constant water pressure
in the water supply.
Fig. 11 JPA PM and PT boosters
Fig. 12 JPC PM and JPC PT
4.3 JPD PT
JPD PT are self-priming centrifugal boosters for
suction lifts up to 27 m. The pump body is made of
cast iron. The high suction lift is achieved by means
of an ejector which can be inserted into wells with a
diameter of down to 10 cm (4"). The boosters are
especially suited for use in small-scale agriculture
and water supply to farmhouses.
Fig. 13 JPD boosters
TM06 5406 4515 TM06 5410 4515 TM06 5411 4515
TM05 5091 3212
TM06 5408 4515 TM06 5409 4515 TM06 6703 2216
TM05 8007 2216
TM06 5413 4515 - TM06 5415 4515

English (GB)
8
4.4 Identification
Fig. 14 Nameplate, JPA
Fig. 15 Nameplate, JPC
Fig. 16 Nameplate, JPD
TM06 7712 4016TM06 7303 3616
DK-8850 Bjerringbro Denmark
Type: JPA 3-42 No: 98946090 P4 15 47
U: 1x230 V~ I1/1: 3,12 A 50Hz P1: 0,72 kW
12,5 μF / 450 V~ Class: F IP: 44 P2: 0,6 HP
Q: 0,4-2,7 m /h H: 38-21 m Hmix: 21 m
Hmax: 42 mn: 2800 min
Made in Hungary by Grundfos
1
17
16
15
14
13
23
4
5
6
18
19
12 11 10 9
3
-1 Serial nr.146783
pmax : 0.8/8 Mpa/bar Tmax: 35ºC
21 7
8
20
DK-8850 Bjerringbro Denmark
Type: JPC 4-47 No:99074057 P4 1.1628
U: 1x220-240 V~ I1/1:3.8A 50Hz P1:0.85
12.5μF / 450 V~ Class:F IP:44 P2:0.8HP
Q: 0.4-3.6 m /h H: 41-20 m Tmax:55ºC
n: 2800 min Made in Hungary by Grundfos
1
17
16
15
14
13
23
4
5
6
7
8
12 11 10 9
3
-1
TM06 7713 4016
Pos. Description
1 Pump type
2 Product number
3 Full-load current
4 Factory and production date
5 Motor input power
6 Pump output power
7 Maximum temperature
8 Country of production
9 Frequency
10 Enclosure class
11 Motor insulation class
12 Head
13 Approvals
14 Speed
15 Maximum flow rate
16 Capacitor data
17 Supply voltage
18 Minimum head
19 Maximum head
20 Serial number
21 Maximum pressure
DK-8850 Bjerringbro Denmark
Type: JPD 4-47 No: 98946103 P51. 1549
U: 1x230 V~ I1/1: 4.22 A 50Hz P1: 0.86 kW
16 μF / 450 V~ Class: F IP: 44 P2: 0.75 HP
Q: 0.12-2.38 m /h H: 35-15 m Hmix: m
Hmax: mn: 2800 min
Made in China by Grundfos
1
17
16
15
14
13
23
4
5
6
18
19
12 11 10 9
3
-1
pmax : 0.6/6 Mpa/bar Tmax: 35ºC
21
7
8
Q&H performed
with Ejector E25
& suction depth 9m
PCS 00084.01 04-6292.2.41
LSPr-002-IDN
NPB 119-116-111053

English (GB)
9
5. Servicing the product
5.1 Maintaining the product
In normal operation, the pump does not require any
specific maintenance.
5.1.1 Safety instructions and requirements
5.2 Spare parts and kits
Service kits are available for the JPA, JPC, JPD
pumps and boosters.
The service kits consist of the following replaceable
parts:
• shaft seal
• hydraulic parts
• capacitor.
DANGER
Electric shock
Death or serious personal injury
- If the power supply cable is damaged, it
must be replaced by the manufacturer,
his service agent or similarly qualified
persons in order to avoid hazard.
Service must only be performed by trained
service staff.

English (GB)
10
6. Fault finding
DANGER
Electric shock
Death or serious personal injury
- Switch off the power supply before
starting any work on the product. Make
sure that the power supply cannot be
accidentally switched on.
Fault Cause Remedy
1. The pump does
not start.
a) Supply failure. Cut in the circuit breaker or replace the fuses.
If the new fuses also blow, check the electric
installation.
b) The pump is blocked by
impurities.
Clean the pump. Check or replace the strainer
in the inlet pipe.
c) The motor is defective. Replace the pump.
2. The pump runs,
but gives no or just
a little water.
a) The pump is not filled with
water.
Prime the pump. See section 3. Starting up the
product.
b) The inlet pipe is blocked by
impurities.
Clean the inlet pipe. Check or replace the
strainer in the inlet pipe.
c) The pump is blocked by
impurities.
Clean the pump. Check or replace the strainer
in the inlet pipe.
d) The suction lift is too high.
JPA, JPC: Maximum 7 m.
JPD: Maximum 27 m.
Change the position of the pump.
e) The inlet pipe is too long. Change the position of the pump.
f) The diameter of the inlet pipe
is too small. Replace the inlet pipe.
g) The inlet pipe is not immersed
deeply enough.
Make sure that the inlet pipe is immersed
sufficiently.
h) The inlet pipe is leaking. Repair or replace the pipe.
3. The pump runs,
but gives no water
or delivers a
reduced quantity
of water at high
pressure.
a) The outlet pipe is blocked.
Clean the pipe or open the isolating valves, if
fitted.
Check that no additional work is being carried
out in the system.
4. The motor cuts out
during operation.
a) The thermal switch in the
motor has tripped due to
overheating.
The thermal switch will cut in automatically
when the motor has cooled sufficiently.
If the problem persists, check these two
possible causes:
• The impeller is stuck.
Clean the pump.
• The motor is defective.
Replace the pump.

English (GB)
11
7. Technical data
Maximum ambient temperature
35 or 55 °C. See the nameplate.
Liquid temperature
Domestic use: 0-35 °C or 0-60 °C. See the
nameplate.
Other use: 0-40 °C.
Maximum operating pressure
6 bar, 600 kPa.
Maximum flow rate
Maximum head
Maximum inlet pressure
Maximum suction lift
JPA, JPC: 8 m, including a pressure loss, at a liquid
temperature of 20 °C.
JPD: 27 m.
Pump type [m3/h]
JPA 3-42 / JPA 3-42 PT-H 3
JPA 4-47 / JPA 4-47 PT-H /
JPA 4-47 PT-V 4
JPA 4-54 / JPA 4-54 PT-H /
JPA 4-54 PT-V 4
JPA 5-61 / JPA 5-61 PT-V 5
JPA 8-62 / JPA 8-62 PT-V 8
JPA 12-41 12
JPA 12-51 12
JPC 3-42 / JPC 3-42 PT 3
JPC 4-47 / JPC 4-47 PT 4
JPC 4-54 / JPC 4-54 PT 4
JPC 5-48 5
JPD 4-47 PT 4
JPD 4-54 PT 4
JPD 5-61 PT 5
JPD 8-62 PT 8
Pump type [m]
JPA 3-42 / JPA 3-42 PT-H 42
JPA 4-47 / JPA 4-47 PT-H /
JPA 4-47 PT-V 47
JPA 4-54 / JPA 4-54 PT-H /
JPA 4-54 PT-V 54
JPA 5-61 / JPA 5-61 PT-V 61
JPA 8-62 / JPA 8-62 PT-V 62
JPA 12-41 41
JPA 12-51 51
JPC 3-42 / JPC 3-42 PT 42
JPC 4-47 / JPC 4-47 PT 47
JPC 4-54 / JPC 4-54 PT 54
JPC 5-48 48
JPD 4-47 PT 47
JPD 4-54 PT 54
JPD 5-61 PT 61
JPD 8-62 PT 62
Pump type [bar] [MPa]
JPA 3-42 / JPA 3-42 PT-H 3.8 0.38
JPA 4-47 / JPA 4-47 PT-H /
JPA 4-47 PT-V 3.3 0.33
JPA 4-54 / JPA 4-54 PT-H /
JPA 4-54 PT-V 2.6 0.26
JPA 5-61 / JPA 5-61 PT-V 1.9 0.19
JPA 8-62 / JPA 8-62 PT-V 1.8 0.18
JPA 12-41 3.9 0.39
JPA 12-51 2.9 0.29
JPC 3-42 / JPC 3-42 PT 1.8 0.18
JPC 4-47 / JPC 4-47 PT 1.3 0.13
JPC 4-54 / JPC 4-54 PT 0.6 0.06
JPC 5-48 1.2 0.12
JPD 4-47 PT 1.3 0.13
JPD 4-54 PT 0.6 0.06
JPD 5-61 PT 1.9 0.19
JPD 8-62 PT 1.8 0.18

English (GB)
12
Supply voltage
Insulation class
F.
Enclosure class
IP44.
Relative air humidity
Maximum 95 %.
Maximum sound pressure level
JPA, JPD: less than 77 dB(A).
JPC 3-42: 82.9 dB.
JPC 4-47: 84.8 dB.
JPC 4-54: 88.0 dB.
Frequency of starts and stops
Maximum 20 per hour.
8. Disposing of the product
This product or parts of it must be disposed of in an
environmentally sound way:
1. Use the public or private waste collection service.
2. If this is not possible, contact the nearest
Grundfos company or service workshop.
See also end-of-life information on
www.grundfos.com.
The crossed-out wheelie bin symbol on
a product means that it must be
disposed of separately from household
waste. When a product marked with this
symbol reaches its end of life, take it to a
collection point designated by the local
waste disposal authorities. The separate collection
and recycling of such products will help protect the
environment and human health.
JPA JPC JPD
1 x 115 V, 60 Hz - ●-
1 x 230 V, 60 Hz - ●-
1 x 230 V, 50 Hz ●●●

13

Grundfos companies
Argentina
Bombas GRUNDFOS de Argentina S.A.
Ruta Panamericana km. 37.500 Centro
Industrial Garin
1619 Garín Pcia. de B.A.
Phone: [phone]
Telefax: [phone]
Australia
GRUNDFOS Pumps Pty. Ltd.
P.O. Box 2040
Regency Park
South Australia 5942
Phone: [phone]
Telefax: [phone]
Austria
GRUNDFOS Pumpen Vertrieb
Ges.m.b.H.
Grundfosstraße 2
A-5082 Grödig/Salzburg
Tel.: [phone]
Telefax: [phone]
Belgium
N.V. GRUNDFOS Bellux S.A.
Boomsesteenweg 81-83
B-2630 Aartselaar
Tél.: [phone]
Télécopie: [phone]
Belarus
Представительство ГРУНДФОС в
Минске
220125, Минск
ул. Шафарнянская, 11, оф. 56, БЦ
«Порт»
Тел.: [phone]
Факс: [phone]
E-mail: [email protected]
Bosnia and Herzegovina
GRUNDFOS Sarajevo
Zmaja od Bosne 7-7A,
BH-71000 Sarajevo
Phone: [phone]
Telefax: [phone]
www.ba.grundfos.com
e-mail: [e-mail]
Brazil
BOMBAS GRUNDFOS DO BRASIL
Av. Humberto de Alencar Castelo
Branco, 630
CEP 09850 - 300
São Bernardo do Campo - SP
Phone: [phone]
Telefax: [phone]
Bulgaria
Grundfos Bulgaria EOOD
Slatina District
Iztochna Tangenta street no. 100
BG - 1592 Sofia
Tel. [phone]
Fax. [phone]
email: [e-mail]
Canada
GRUNDFOS Canada Inc.
2941 Brighton Road
Oakville, Ontario
L6H 6C9
Phone: [phone]
Telefax: [phone]
China
GRUNDFOS Pumps (Shanghai) Co. Ltd.
10F The Hub, No. 33 Suhong Road
Minhang District
Shanghai 201106
PRC
Phone: [phone]
Telefax: [phone]
COLOMBIA
GRUNDFOS Colombia S.A.S.
Km 1.5 vía Siberia-Cota Conj. Potrero
Chico,
Parque Empresarial Arcos de Cota Bod.
1A.
Cota, Cundinamarca
Phone: [phone]
Telefax: [phone]
Croatia
GRUNDFOS CROATIA d.o.o.
Buzinski prilaz 38, Buzin
HR-10010 Zagreb
Phone: [phone]
Telefax: [phone]
www.hr.grundfos.com
GRUNDFOS Sales Czechia and
Slovakia s.r.o.
Čajkovského 21
779 00 Olomouc
Phone: [phone]
Denmark
GRUNDFOS DK A/S
Martin Bachs Vej 3
DK-8850 Bjerringbro
Tlf.: [phone]
Telefax: [phone]
E-mail: [email protected]
www.grundfos.com/DK
Estonia
GRUNDFOS Pumps Eesti OÜ
Peterburi tee 92G
11415 Tallinn
Tel: + 372 606 1690
Fax: + 372 606 1691
Finland
OY GRUNDFOS Pumput AB
Trukkikuja 1
FI-01360 Vantaa
Phone: [phone]
France
Pompes GRUNDFOS Distribution S.A.
Parc d’Activités de Chesnes
57, rue de Malacombe
F-38290 St. Quentin Fallavier (Lyon)
Tél.: [phone]
Télécopie: [phone]
Germany
GRUNDFOS GMBH
Schlüterstr. 33
40699 Erkrath
Tel.: [phone]
Telefax: [phone]
e-mail: [e-mail]
Service in Deutschland:
e-mail: kundendi[email protected]
Greece
GRUNDFOS Hellas A.E.B.E.
20th km. Athinon-Markopoulou Av.
P.O. Box 71
GR-19002 Peania
Phone: [phone]
Telefax: +0030-210-66 46 273
Hong Kong
GRUNDFOS Pumps (Hong Kong) Ltd.
Unit 1, Ground floor
Siu Wai Industrial Centre
29-33 Wing Hong Street &
68 King Lam Street, Cheung Sha Wan
Kowloon
Phone: [phone]
Telefax: [phone]
Hungary
GRUNDFOS Hungária Kft.
Tópark u. 8
H-2045 Törökbálint,
Phone: [phone]
Telefax: [phone]
India
GRUNDFOS Pumps India Private
Limited
118 Old Mahabalipuram Road
Thoraipakkam
Chennai 600 096
Phone: [phone]
Indonesia
PT. GRUNDFOS POMPA
Graha Intirub Lt. 2 & 3
Jln. Cililitan Besar No.454. Makasar,
Jakarta Timur
ID-Jakarta 13650
Phone: [phone]
Telefax: [phone] / 460 6901
Ireland
GRUNDFOS (Ireland) Ltd.
Unit A, Merrywell Business Park
Ballymount Road Lower
Dublin 12
Phone: [phone]
Telefax: [phone]
Italy
GRUNDFOS Pompe Italia S.r.l.
Via Gran Sasso 4
I-20060 Truccazzano (Milano)
Tel.: [phone]
Telefax: [phone] / 95838461
Japan
GRUNDFOS Pumps K.K.
1-2-3, Shin-Miyakoda, Kita-ku,
Hamamatsu
431-2103 Japan
Phone: [phone]
Telefax: [phone]
Korea
GRUNDFOS Pumps Korea Ltd.
6th Floor, Aju Building 679-5
Yeoksam-dong, Kangnam-ku, 135-916
Seoul, Korea
Phone: [phone]
Telefax: [phone]
Latvia
SIA GRUNDFOS Pumps Latvia
Deglava biznesa centrs
Augusta Deglava ielā60, LV-1035, Rīga,
Tālr.: + 371 714 9640, 7 149 641
Fakss: + 371 914 9646
Lithuania
GRUNDFOS Pumps UAB
Smolensko g. 6
LT-03201 Vilnius
Tel: + 370 52 395 430
Fax: + 370 52 395 431

Grundfos companies
Malaysia
GRUNDFOS Pumps Sdn. Bhd.
7 Jalan Peguam U1/25
Glenmarie Industrial Park
40150 Shah Alam
Selangor
Phone: [phone]
Telefax: [phone]
Mexico
Bombas GRUNDFOS de México S.A. de
C.V.
Boulevard TLC No. 15
Parque Industrial Stiva Aeropuerto
Apodaca, N.L. 66600
Phone: [phone]
Telefax: [phone]
Netherlands
GRUNDFOS Netherlands
Veluwezoom 35
1326 AE Almere
Postbus 22015
1302 CA ALMERE
Tel.: [phone]
Telefax: [phone]
E-mail: [e-mail]
New Zealand
GRUNDFOS Pumps NZ Ltd.
17 Beatrice Tinsley Crescent
North Harbour Industrial Estate
Albany, Auckland
Phone: [phone]
Telefax: [phone]
Norway
GRUNDFOS Pumper A/S
Strømsveien 344
Postboks 235, Leirdal
N-1011 Oslo
Tlf.: [phone]
Telefax: [phone]
Poland
GRUNDFOS Pompy Sp. z o.o.
ul. Klonowa 23
Baranowo k. Poznania
PL-62-081 Przeźmierowo
Tel: [phone]
Fax: [phone]
Portugal
Bombas GRUNDFOS Portugal, S.A.
Rua Calvet de Magalhães, 241
Apartado 1079
P-2770-153 Paço de Arcos
Tel.: [phone]
Telefax: [phone]
Romania
GRUNDFOS Pompe România SRL
Bd. Biruintei, nr 103
Pantelimon county Ilfov
Phone: [phone]
Telefax: [phone]
E-mail: [e-mail]
Russia
ООО Грундфос Россия
ул. Школьная, 39-41
Москва, RU-109544, Russia
Тел. [phone] (495) 737-30-
00
Факс [phone]
E-mail [e-mail]
Serbia
Grundfos Srbija d.o.o.
Omladinskih brigada 90b
11070 Novi Beograd
Phone: [phone]
Telefax: [phone]
www.rs.grundfos.com
Singapore
GRUNDFOS (Singapore) Pte. Ltd.
25 Jalan Tukang
Singapore 619264
Phone: [phone]
Telefax: [phone]
Slovakia
GRUNDFOS s.r.o.
Prievozská 4D
821 09 BRATISLAVA
Phona: [phone]
sk.grundfos.com
Slovenia
GRUNDFOS LJUBLJANA, d.o.o.
Leskoškova 9e, 1122 Ljubljana
Phone: [phone]
Telefax: [phone]
E-mail: [email protected]
South Africa
Grundfos (PTY) Ltd.
16 Lascelles Drive, Meadowbrook Estate
1609 Germiston, Johannesburg
Tel.: [phone]
Fax: [phone]
E-mail: [e-mail]
Spain
Bombas GRUNDFOS España S.A.
Camino de la Fuentecilla, s/n
E-28110 Algete (Madrid)
Tel.: [phone]
Telefax: [phone]
Sweden
GRUNDFOS AB
Box 333 (Lunnagårdsgatan 6)
431 24 Mölndal
Tel.: [phone]
Telefax: [phone]
Switzerland
GRUNDFOS Pumpen AG
Bruggacherstrasse 10
CH-8117 Fällanden/ZH
Tel.: [phone]
Telefax: [phone]
Taiwan
GRUNDFOS Pumps (Taiwan) Ltd.
7 Floor, 219 Min-Chuan Road
Taichung, Taiwan, R.O.C.
Phone: [phone]
Telefax: [phone]
Thailand
GRUNDFOS (Thailand) Ltd.
92 Chaloem Phrakiat Rama 9 Road,
Dokmai, Pravej, Bangkok 10250
Phone: [phone]
Telefax: [phone]
Turkey
GRUNDFOS POMPA San. ve Tic. Ltd.
Sti.
Gebze Organize Sanayi Bölgesi
Ihsan dede Caddesi,
2. yol 200. Sokak No. 204
41490 Gebze/ Kocaeli
Phone: +90 - 262-679 7979
Telefax: +90 - 262-679 7905
E-mail: [e-mail]
Ukraine
Бізнес Центр Європа
Столичне шосе, 103
м. Київ, 03131, Україна
Телефон: [phone]
Факс.: [phone]
E-mail: [e-mail]
United Arab Emirates
GRUNDFOS Gulf Distribution
P.O. Box 16768
Jebel Ali Free Zone
Dubai
Phone: [phone]
Telefax: [phone]
United Kingdom
GRUNDFOS Pumps Ltd.
Grovebury Road
Leighton Buzzard/Beds. LU7 4TL
Phone: [phone]
Telefax: [phone]
U.S.A.
GRUNDFOS Pumps Corporation
9300 Loiret Blvd.
Lenexa, Kansas 66219
Phone: [phone]
Telefax: [phone]
Uzbekistan
Grundfos Tashkent, Uzbekistan The Rep-
resentative Office of Grundfos Kazakhstan
in Uzbekistan
38a, Oybek street, Tashkent
Телефон: [phone] / 71 150
3291
Факс: [phone]
Addresses Revised 15.01.2019

www.grundfos.com
99022277 0119
ECM: 1252450
Trademarks displayed in this material, including but not limited to Grundfos, the Grundfos logo and “be think innovate” are registered trademarks owned by The Grundfos Group. All rights reserved. © 2019 Grundfos Holding A/S, all rights reserved.