Grundfos Multilift MD Series User manual

Multilift MD, MLD
Installation and operating instructions
GRUNDFOS INSTRUCTIONS

2

Table of contents
3
Multilift MD, MLD
English (GB)
Installation and operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Български (BG)
Упътване за монтаж иексплоатация . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Čeština (CZ)
Montážní a provozní návod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Dansk (DK)
Monterings- og driftsinstruktion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Deutsch (DE)
Montage- und Betriebsanleitung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Eesti (EE)
Paigaldus- ja kasutusjuhend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Ελληνικά (GR)
Οδηγίες εγκατάστασης και λειτουργίας . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Español (ES)
Instrucciones de instalación y funcionamiento. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Français (FR)
Notice d'installation et de fonctionnement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Hrvatski (HR)
Montažne i pogonske upute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Italiano (IT)
Istruzioni di installazione e funzionamento. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
Қазақша (KZ)
Орнату жəне пайдалану нұсқаулықтары . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
Latviešu (LV)
Uzstādīšanas un ekspluatācijas instrukcija . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
Lietuviškai (LT)
Įrengimo ir naudojimo instrukcija . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
Magyar (HU)
Telepítési és üzemeltetési utasítás . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387
Nederlands (NL)
Installatie- en bedieningsinstructies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415
Українська (UA)
Інструкції змонтажу та експлуатації . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442
Polski (PL)
Instrukcja montażu i eksploatacji . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470
Português (PT)
Instruções de instalação e funcionamento. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 498
Русский (RU)
Паспорт, Руководство по монтажу иэксплуатации . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 526
Română(RO)
Instrucţiuni de instalare şi utilizare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556
Slovenčina (SK)
Návod na montáž a prevádzku . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 583
Slovensko (SI)
Navodila za montažo in obratovanje . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 611
Srpski (RS)
Uputstvo za instalaciju i rad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 639

Table of contents
4
Multilift MD, MLD
Suomi (FI)
Asennus- ja käyttöohjeet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 667
Svenska (SE)
Monterings- och driftsinstruktion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 694
Türkçe (TR)
Montaj ve kullanım kılavuzu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 721
中文 (CN)
安装和使用说明书 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 749
Appendix 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 774
Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 776
Declaration of conformity RU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 778
Declaration of performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 779

English (GB)
5
English (GB) Installation and operating instructions
Original installation and operating instructions.
TABLE OF CONTENTS
Page
1. Symbols used in this document
2. Scope of delivery
2.1 MD
Grundfos Multilift MD lifting stations are supplied complete with
collecting tank, butterfly-non-return valves, a sensor unit with
cable and two pumps with cable, both connected to the LC 221
controller. The controller includes a power supply cable with plug.
An accessories bag containing the following items is also
included:
• 1 x installation and operating instructions
• 1 x Quick guide for controller menu
• 1 x discharge adapter flange, DN 80, with connection piece,
DN 100 (outer diameter, 110 mm)
• 1 x flexible hose, DN 100, and two clamps to connect the
discharge pipe
• 1 x flexible hose, DN 70, and two clamps to connect the
venting pipe
• 2 x screw and expansion anchor for tank fixation
• 3 x screw and washer for fastening a pipe plug in the inlet disk,
if required
• 1 x socket seal, DN 100
• 1 x socket seal, DN 50, for diaphragm pump connection or
inlet, DN 50
• 1 x gasket kit, DN 80, 8 bolts M16 x 65, nuts and washers
(galvanized).
2.2 MLD
Grundfos Multilift MLD lifting stations are supplied complete with
collecting tank, butterfly-non-return valves, a sensor unit with
cable and two pumps with cable, both connected to the LC 221
controller. The controller includes a power supply cable with plug.
An accessories bag containing the following items is also
included:
• 1 x installation and operating instructions
• 1 x Quick guide for controller menu
• 1 x discharge adapter flange, DN 80, with connection piece,
DN 100 (outer diameter, 110 mm)
• 1 x flexible hose, DN 100, and two clamps to connect
discharge pipe
• 1 x flexible hose, DN 70, and two clamps to connect venting
pipe
• 4 x screw and expansion anchor for tank fixation
• 1 x socket seal, DN 150
• 1 x flexible hose connection with two clamps, DN 50, for
diaphragm pump connection or inlet, DN 50
• 1 x gasket kit, DN 80, 8 bolts M16 x 65, nuts and washers
(galvanized).
1. Symbols used in this document 5
2. Scope of delivery 5
2.1 MD 5
2.2 MLD 5
3. General description 6
3.1 Applications 7
4. Transportation and storage 7
5. Product description 7
5.1 Lifting station 7
5.2 LC 221 controller 9
6. Operating LC 221 controller 13
6.1 Description of display 13
6.2 Setup menu 15
6.3 Information menu 16
6.4 Description of fault indications 17
7. Installation of lifting station 19
7.1 General description 19
7.2 Guidelines for installation of lifting station 20
7.3 Procedure for installation of lifting station 20
8. Installation of LC 221 controller 22
8.1 Location 22
8.2 Mechanical installation 22
8.3 Electrical connection 23
8.4 Setting of LC 221 23
8.5 Wiring diagrams 24
9. Startup 25
10. Maintenance and service 25
10.1 Mechanical maintenance 26
10.2 Motor 26
10.3 Electrical maintenance 26
10.4 Cleaning the level sensor 27
10.5 Contaminated lifting station or components 27
11. Fault finding 28
12. Technical data 29
12.1 Lifting station 29
12.2 Collecting tank 29
12.3 Pump 29
12.4 LC 221 controller 29
12.5 Performance curves 30
13. Disposal 31
Warning
Prior to installation, read these installation and
operating instructions. Installation and operation
must comply with local regulations and accepted
codes of good practice.
Warning
The use of this product requires experience with
and knowledge of the product.
Persons with reduced physical, sensory or
mental capabilities must not use this product,
unless they are under supervision or have been
instructed in the use of the product by a person
responsible for their safety.
Children must not use or play with this product.
Warning
If these safety instructions are not observed,
it may result in personal injury.
Warning
These instructions must be observed for
explosion-proof pumps. We recommend that you
also follow these instructions for standard
pumps.
Caution
If these safety instructions are not observed,
it may result in malfunction or damage to the
equipment.
Note
Notes or instructions that make the job easier
and ensure safe operation.

English (GB)
6
3. General description
Grundfos Multilift MD and MLD lifting stations are supplied
complete with collecting tank, pumps, level sensor, LC 221
controller and connection accessories.
The following gives a description of the components.
Fig. 1 Multilift MD front and rear view Fig. 2 Multilift MLD front and rear view
TM05 1521 2911
Pos. Description
1Pump
2 Lifting eye for pumps
3Nameplate
4 Venting port, DN 70 (outer diameter, 75 mm), open
5 Screw cap for pressure tube and tank inspection opening
6 Vertical inlet, DN 150 (seal is accessory)
7 Fixing point
8Non-return butterfly valve, DN 80, with inspection cover
and drain screw to lift up the valve flap
9Discharge adapter flange, DN 80, to pipe ∅110 with
flexible connection piece and 2 clamps
10 Side or top inlet, DN 50 (seals are accessory).
Socket for MD; connecting piece for MLD
11 Collecting tank with carrying handle moulded into tank
body
12
Port for manually operated diaphragm pump, 1 1/2".
Socket with seal for MD; connecting piece with flexible
connection hose and clamps for MLD
13 Horizontal inlet, DN 100 (seal is accessory)
14 Adjustable inlet disk, DN 100
(DN 150 optional as accessory)
15 Separate inspection cover
TM05 1522 2911

English (GB)
7
3.1 Applications
Grundfos Multilift MD and MLD lifting stations are designed for
the collection and pumping of domestic wastewater with no free
flow to sewer level. Grundfos Multilift MD and MLD lifting stations
are designed for the collection and pumping of the following
liquids:
• domestic wastewater, including grey wastewater without
faeces, black wastewater with faeces (discharge from water
closets)
• sludge-containing water.
The lifting stations are capable of pumping liquids containing
fibres, textiles, faeces, etc., below sewer level from multi-family
houses, offices, schools, hotels, restaurants, public areas and
other commercial buildings and similar industrial applications.
Do not pump rainwater with the Multilift MD and MLD lifting
stations for these two reasons:
• The motors of the lifting stations are not designed for
continuous operation which may be necessary in case of
heavy rainfall.
• Rainwater must not be discharged into a lifting station inside a
building according to EN 12056-4.
If in doubt, please contact Grundfos for advice.
Do not discharge the following substances/types of wastewater
via a lifting station:
• solid matter, tar, high content of sand, cement, ash, cardboard,
debris, garbage etc.
• wastewater from sanitary installations situated above the flood
level (this should be drained away via a free-flow drainage
system according to EN 12056-1).
• wastewater containing hazardous substances such as greasy
wastewater from large-scale catering establishments.
For drainage of greasy wastewater, use a grease separator
according to EN 1825-2 between a canteen or commercial
kitchen and the Multilift MD or MLD.
4. Transportation and storage
For long periods of storage, the LC 221 controller must be
protected against moisture and heat.
After a long period of storage, the pumps should be inspected
before they are started up again. Make sure that the impellers
can rotate freely.
5. Product description
The MD and MLD Multilift lifting stations are described in the
following sections:
• section 5.1 Lifting station describing the lifting station with
collecting tank, pumps, non-return valve and level sensor
• section 5.2 LC 221 controller describing the controller as well
as the functions and operation of the controller.
In section 7. Installation of lifting station and the following
sections, the above components are described as one unit.
5.1 Lifting station
The Grundfos Multilift MD and MLD lifting stations are supplied
complete with two single- or three-phase submersible pumps
connected to the LC 221 controller incorporating a level sensor.
Type key, lifting station
Nameplate, lifting station
Fig. 3 Nameplate, lifting station
Warning
The motor lifting eye is only intended for lifting
the pump. Never lift or lower the lifting station by
means of the lifting eye.
Note
Lift the lifting station by the collecting tank.
Example M L D .22 .3 .4
Multilift lifting station
L = large tank
D = 2 pumps
Output power, P2 / 100 (W)
1 = single-phase motor
3 = three-phase motor
2 = 2-pole motor
4 = 4-pole motor
TM04 7639 2210
Pos. Description
1 Type designation
2 Product number
3 Production code (year/week)
4 Frequency [Hz]
5 Number of phases + voltage [V]
6 Voltage [V]
7 Full-load current [A]
8 Motor input power P1 [kW]
9CEmark
10 Duty type
11 Serial number
12 Maximum flow rate [m3/h]
13 Minimum head [m]
14 Maximum head [m]
15 Maximum liquid temperature [°C]
16 Maximum ambient temperature [°C]
17 Weight [kg]
18 Blank

English (GB)
8
5.1.1 Collecting tank
The gas-, odour- and pressure-tight collecting tank is made of
wastewater resistant polyethylene (PE) and has all necessary
ports for the connection of inlet pipes, discharge pipe, venting
pipe and a manually operated diaphragm pump, which is
available as an accessory.
The MD collecting tank has a turnable, eccentric disk in the
back allowing adjustment of the inlet to any height between 180
and 315 mm above the floor. The most common heights are
marked beside the inlet. See section 7.3 Procedure for
installation of lifting station.
Furthermore, the MD collecting tank offers four horizontal inlets in
the sides (2 x DN 100 and 2 x DN 50) and three vertical inlets at
the top of the tank (2 x DN 150 and 1 x DN 50). The centres of the
horizontal inlets are 120 mm (DN 50) and 250 mm (DN 150)
above the floor.
The side and back inlets 180 and 250 mm above the floor are for
direct connection to wall-hung or floor-standing toilet according to
EN 33 and EN 37. Further sanitary appliances can be connected
to the other ports.
The MLD collecting tank offers one vertical inlet, DN 50, at the
top of the tank and one vertical inlet, DN 150, in the stepped part
of the tank.
The tank volume and effective volume (volume between start and
stop) for Multilift MD and MLD lifting stations appear from the
following table:
Setting to the relevant start inlet level must be made during the
start-up phase via the setup menu. See section 6.2 Setup menu.
The first step after power supply connection is a start-up phase
with level setting.
To minimise sedimentation, the tank bottom is chamfered to lead
the wastewater to the pump.
5.1.2 Pumps
The pump impellers are designed as free-flow vortex impellers,
ensuring almost unchanged performance throughout the entire
life of the pump. See the pump curves in section
12.5 Performance curves. The stator housing of the motor is
made of cast iron. The pump has a mechanical shaft seal.
See more technical data in section 12. Technical data.
Single-phase motors are protected by a thermal switch in the
windings and run via a capacitor inside the controller cabinet.
Three-phase motors are protected by a thermal switch in the
windings and an additional thermal circuit breaker in the cabinet
of Multilift MD/MLD22, 24, 32 and 38 to cut out the motor in case
of overload.
If the phase sequence for three-phase pumps is wrong, the
controller will indicate fault and prevent the pump(s) from starting.
For correction of phase sequence, see fig. 14. For direction of
rotation, see section 10.2 Motor.
5.1.3 Shaft seal
The pumps have three shaft seals, the oil chambers in between are
filled for life and therefore require no maintenance.
For replacement in case of service, please see service
instructions.
5.1.4 Motor cable
The motor cable is fitted to the motor via a cable entry.
The enclosure class is IP68. The length of the cable is either 4 m
or 10 m.
Nameplate, motor
Fig. 4 Nameplate, motor
5.1.5 Non return valve
The DN 80 non-return valve includes a drain screw to lift up the
internal flap in order to drain the discharge pipe in case of
maintenance or service. The valve is designed and tested
according to EN12050-4. See fig. 5.
Fig. 5 Butterfly (double) non-return valve, DN 80
MD
Inlet level [mm] 180 250 315
Total tank volume [l] 130
Effective tank volume [l] 49 69 86
MLD
Inlet level [mm] 560
Total tank volume [l] 270
Effective tank volume [l] 190
Note
If the motor is overloaded, it will stop
automatically.
When it has cooled to normal temperature, it will
restart automatically.
TM03 3618 0506
Pos. Description
19 Product number and model
20 Number of phases
21 Frequency
22 Input power
23 Shaft power
24 Power factor
25 Enclosure class
26 Production country
27 CE mark
28 Production week and year
29 Operating mode
30 Rated speed
31 Weight
32 Insulation class
33 Rated voltage
34 Rated current
Note
Loosen the lock nut a little before turning the
drain screw.
TM051530 2911
Made in Germany
kW
Hz
~
96075378 - A
kW
96075389
P. c.
min
-1
kg
n
Weight
0149 001
S3-40%-1min
1405
24
F
Insul.class
Prod.- No.
U
P
2
V
A
I
1/1
Motor
5.3
400
3
50
2.8
IP68
2.2
P
1
0.77
22
23
21
20
19
24
25
26
27
32
31
30
29
28
33
34
COS
$

English (GB)
9
5.1.6 Level sensor, Multilift MD, MLD
The piezoresistive pressure sensor placed in the controller is
connected via a hose to a pressure tube in the tank. The screw
cap where the hose is connected includes a condensate trap and
a connection for a DN 100 tube. This tube, the pressure tube,
extends down into the tank. The rising liquid level compresses the
air inside the pressure tube and hose, and the piezoresistive
sensor transforms the changing pressure into an analogue signal.
The control box uses the analogue signal to start and stop the
pump and to indicate high water-level alarm. The pressure tube is
fixed underneath the screw cap and can be taken out for
maintenance, service and for cleaning the inside of the tube.
An O-ring ensures tightness.
The hose is supplied in lengths of 4 or 10 m. The hose must be
connected to the controller.
Fig. 6 Screw cap with hose, DN 100 tube and condensate
trap
5.2 LC 221 controller
The LC 221 is a level controller specially designed for controlling
and monitoring the Grundfos lifting stations, Multilift MD and
MLD. The basis for the control is the signal received continuously
from the piezoresistive, analogue level sensor.
The level controller switches the MD and MLD Multilift pumps on
and off according to the liquid level measured by the level sensor.
When the first start level is reached, the first pump will start, and
when the liquid level has been lowered to the stop level, the pump
will be stopped by the controller. If the liquid level rises up to the
second start level, the second pump will also start, and when the
liquid level has been lowered to the stop level, the pumps will be
stopped by the controller.
Starts alternate between the two pumps.
In case of pump failure in one pump, the other pump will take
over (automatic pump changeover).
An alarm will be indicated in case of high water-level in the tank,
pump failure, etc.
Furthermore, the level controller has many more functions as
described below.
Fig. 7 LC 221 level controller for Multilift MD and MLD
The LC 221 controller has the following functions:
• on/off control of two wastewater pumps based on a continuous
signal from a piezoresistive level sensor with alternating
operation and automatic changeover in case of pump failure
• motor protection with motor-protective circuit breaker and/or
current measurement as well as connection of thermal
switches
• motor protection via operating-time limitation with subsequent
emergency operation. Normal operating times are max.
25 seconds (MD) and 55 seconds (MLD), and the operating
time is limited to three minutes (see section 6.4 Description of
fault indications, fault code F011).
• automatic test runs (2 seconds) during long periods of
inactivity (24 hours after last operation)
• re-starting delay up to 45 seconds after returning from power
cut-off to mains operation (in order to even out the mains load
when several appliances are started up at the same time)
TM05 0332 1011
TM05 1859 3811

English (GB)
10
• setting of delay times:
– stopping delay (time from the stop level is reached till the
pump is stopped) - reduces water hammer if pipes are long
– starting delay (time from the start level is reached till the
pump is started)
– alarm delay (time from a fault appears till an alarm is
indicated). This prevents short-time high-level alarm in case
of temporary high inflow to the tank.
• automatic current measurement for alarm indications
• setting of current values:
– overcurrent (preset)
– rated current (preset)
– dry running current (preset).
• operating indication of:
– operating mode (auto, manual)
– operating hours
– impulses (number of starts)
– highest measured motor current.
• alarm indication of:
– pump status (running, fault)
– phase sequence failure and missing phase
– thermal-switch failure
– high-water alarm
– time for service/maintenance (selectable).
• selection of automatic alarm resetting
• fault log of up to 20 alarms
• selection between different start levels
• selection of connected sensor type
• calibration of sensor (preset)
• selection of maintenance interval (0, 3, 6 or 12 months).
As standard, the LC 221 has four potential-free outputs for:
– pump running
– pump failure
– high water-level alarm
– common fault.
Furthermore, LC 221 has six digital inputs for the following
functions:
– connecting an analogue sensor (4-20 mA or 0-5 V)
– connecting up to four level switches and pressure sensors
instead of analogue sensor. An additional float switch can
be connected to the alarm input as backup for the analogue
sensor.
– connecting a separate level switch to be used for flood
detection outside Multilift MD or MLD. Lifting stations are
often installed in a sump inside the basement - the lowest
point in the building. In case of e.g. groundwater inflow or
water pipe burst, an alarm will be indicated by the controller.
– connecting a piezoresistive pressure sensor PCB
(pre-assembled)
– connecting an external alarm reset
– connecting the thermal switch of the motor.
For bus communication, the LC 221 can be equipped with a
GENIbus interface (available end of 2012) for connection to
Grundfos CIU 300 BACnet MS/TP.
For updates and further adjustments, a PC Tool can be
connected. See service instructions.
To allow for the situation that the normal power supply should fail,
a battery (accessory) can be installed which activates an acoustic
alarm (buzzer). The buzzer is activated as long as the fault exists.
It cannot be reset.
In case of sectional power failure, the common alarm output
which is a potential-free changeover contact can be used to
forward the alarm signal to a control room by means of an
external power source.
Type key, LC 221 controller
Nameplate, LC 221 controller
The controller type, voltage variant, etc. are stated in the type
designation on the nameplate situated on the side of the
controller cabinet.
Fig. 8 Example of an LC 221 nameplate
Example LC 221 .2 .230 .1 .10 .30
LC 221 = controller type
1 = one-pump controller
2 = two-pump controller
Voltage [V]
1 = single-phase
3 = three-phase
Max. operating current [A]
Capacitors [μF]
Starting method:
[ ] = DOL
SD = Star-delta
TM05 1870 3311
Pos. Description
1 Type designation
2 Product number
3 Version number
4 Rated voltage
5 Power consumption
6 Maximum back-up fuse
7 Weight
8 Maximum pump input current
9 Production year and week
10 Serial number
11 Maximum voltage at potential-free contact
12 Maximum current at potential-free contact
13 Ambient temperature
14 Enclosure class
Type LC 221.1.230.1.10.30/150 MPU P.C. 1133
Prod. No. 97901151 V01 Serial No. 0001
U
N V contact max 1 x 220/240 V ~ 50/60 Hz 250 V
P
max V contact max 7 W I Pump max 10 A 250 V
I
Fuse max T Amb .: 0 to 40° C16 A I C < 10 kA
G 3.5 kg
IP 56
Made in Germany
2
13
4
5
6
9
10
11
13
12
7814

English (GB)
11
5.2.1 Design
The LC 221 level controller incorporates the necessary
components to control and protect the pumps, such as relays and
capacitors for single-phase motors, contactors for three-phase
motors and additional motor-protective circuit breaker
(> Multilift MD22 or MLD22).
The control panel offers a user interface with operating buttons
and a display for indication of operating conditions and fault
indications.
Furthermore, it has an integrated piezoresistive pressure sensor
which is activated by compressed air directly via the pressure
tube inside the collecting tank. Finally, it has terminals for power
supply, connection to the pump and the inputs and outputs
mentioned in section 5.2 LC 221 controller.
The front cover is closed by four bayonet fastenings with quarter
turn locks. On the left side, the locks are extended and connected
to the cabinet bottom with hinge strings. The cabinet offers the
possibility of being mounted on a wall without opening it first.
A drilling template and six screws with rubber guides are
enclosed.
5.2.2 Control panel
Fig. 9 Control panel
Display (pos. 1)
The display shows all relevant operating data and fault indications.
The operation and fault indications are described in section
6.1 Description of display.
Operating buttons (pos. 2)
The level controller is operated by the operating buttons placed
under the display. The functions of the operating buttons are
described in the table below:
Status LEDs (pos. 3)
The upper LED (green) is on when the power supply is on.
The lower LED flashes (red) in case of fault to make the fault
visible from a long distance and is thus an addition to the display
symbols and fault codes.
Selector switch (pos. 4)
TM05 1860 3811
Pos. Description
1 Display
2 Operating buttons
3StatusLEDs
4 ON-OFF-AUTO selector switch
1
2
34
Operating
button Description
• go left in the main menu.
• go up in the submenus.
• decrease values in the submenus.
• confirm a selection.
• activate the submenus.
• reset the buzzer.
• go right in the main menu.
• go down in the submenus.
• increase values in the submenus.
Switch Description of function
The operating mode is selected by the
ON-OFF-AUTO selector switch which has three
different positions:
POS I:
Starts the pump manually. The operating time
protection is active and indicates alarm after three
minutes. Normal operating times are up to max.
25 seconds (MD) and 55 seconds (MLD).
POS O:
• Stops the pump when running and cuts off the
power supply to the pump. The three symbols
"Settings locked", "Information" and "Setup" will
be visible.
• Resets fault indications.
POS AUTO:
Automatic operation. The pump will start and stop
according to the signal from the level sensor.

English (GB)
12
5.2.3 Internal layout of LC 221
Figure 10 shows the internal layout of LC 221.
Fig. 10 Internal layout LC 221 (three-phase PCB as example)
TM05 3597 1612 - TM05 3719 1712
Note: Cable connections for pos. 8-15:
Use a cable tie if leads protrude more than
20 mm from the cable sheath.
20 7
7
>20
Pos. Description Comments Terminal designation
1 Terminals for power supply PE, N, L3, L2, L1
2 Terminals for connecting pump 1 PE, N, W1, V1, U1
3 Terminals for connecting pump 2 PE, N, W2, V2, U2
4 Terminals for thermal switch, pump 1 T1, T2
5 Terminals for thermal switch, pump 2 T1, T2
6 Terminals for external alarm 230 V 11, 12
7 Terminals for external reset 230 V 13, 14
8 Terminals for common fault
Potential-free changeover NO/NC
contacts with max. 250 V / 2 A.
Attention: Connect these terminals
to supply network potential or low
voltage but do not mix the two.
X11
9 Terminals for high water-level alarm X10
10 Terminals for failure, pump 2 X9
11 Terminals for failure, pump 1 X8
12 Terminals for operation, pump 2 X7
13 Terminals for operation, pump 1 X6
14
Terminals for level switches Digital 81-88
Terminals for additional high water-level alarm
(inside the tank) Digital 81, 82
15 Terminals for analogue sensor 0-5 V or 4-20 mA 91 (GND), 92 (Signal), 93 (12 V)
16 Service connector to PC Tool -
17 Connector for GENIbus interface module -
18 Control circuit fuse Fine-wire fuse:
100 mA / 20 mm x ∅5-
19 Piezoresistive pressure sensor module 0-5 V -
20 DIP switches (not in use for this application) -
21 Connector for battery, 9 V (accessory) -

English (GB)
13
6. Operating LC 221 controller
6.1 Description of display
The display of the LC 221 level controller is shown in fig. 11.
Fig. 11 LC 221 display
The table below describes the symbols shown in the display as well as the corresponding functions and indications.
TM05 1861 3811
Symbol Function Description
Settings locked The symbol is visible when the setup menu is locked. This prevents unauthorised persons from
making changes to the settings. To unlock the buttons, enter the code 1234.
Automatic operating
mode
The symbol is visible when the level controller is in automatic mode, i.e. when the selector switch
is in position AUTO.
Information
The symbol is visible when there is information about faults, operating hours, number of starts,
max. current of pump. The symbol will be visible if the level controller detects a fault and the fault
will be written into the fault log. After you have entered the fault log, the symbol will switch off.
See section 6.3 Information menu.
Setup
The setup menu holds information about setup for start level, rated current, the stop-, start- and alarm
delay, selection of maintenance interval, reset (automatic or manual) and reset back to factory
settings. For the procedure and a description of the settings, see section 6.2 Setup menu.
Alarm The symbol is visible if an alarm situation occurs. The type of alarm will appear from the
information menu. The symbol disappears when the fault has disappeared.
Impulse counter The symbol is visible when the number of starts in the information menu is shown in the display.
Settable times and fault
indication
The symbol is visible when the operating hours in the information menu and the delays set in the
setup menu are shown in the display. The symbol flashes when max. operating time has been
exceeded.

English (GB)
14
Values in the form of
digits
In automatic mode, faults are indicated by means of a code, and in normal operation these two
values are shown:
• the liquid level in the tank, if the pump is not running
• the current consumption, if the pump is running. If both pumps are running, the current
consumption shown is the value for both pumps.
In the information menu, the following information is indicated:
• fault codes
• operating hours
•impulses
• max. measured motor current.
In the setup menu, the following information is indicated:
•setstartlevel
• set delays
•setcurrents
• sensor calibration (presettings for piezoresistive level sensor)
• service intervals
• total reset to factory settings.
Pump operation and
pump fault in pump 1
The symbol is visible when pump 1 is running and flashes when pump 1 has a fault. In case of
fault, it can be combined with other symbols or fault codes in the display.
Pump operation and
pump fault in pump 2
The symbol is visible when pump 2 is running and flashes when pump 2 has a fault. In case of
fault, it can be combined with other symbols or fault codes in the display.
Phase-sequence fault
(Only three-phase pumps)
The symbol flashes in case of a phase-sequence fault and missing phase.
See section 6.4 Description of fault indications.
Thermal-switch failure The symbol is visible if the motor temperature exceeds the permissible value and the thermal
switch cuts out the pump.
High-water alarm The symbol is visible if the liquid level in the tank reaches max. level.
Liquid level The symbol is visible when the current liquid level is indicated in the middle of the display.
Symbol Function Description

English (GB)
15
6.2 Setup menu
All settings are preset except for the start level. The start level
depends on the inlet height and must be set during the start-up
phase. See section 8.4 Setting of LC 221. However, in case
adjustments are required, settings can be made via the setup
menu. To open the setup menu, mark the symbol using the
button and press the button . Navigate through the menu by
means of the buttons and . Select the desired menu item by
pressing the button . Enter values or select settings from a list
by means of the buttons and . Save the settings by pressing
the button . See also fig. 12.
The following settings can be made:
•startlevel
• rated current
• stop delay
•startdelay
• alarm delay
• sensor selection
• sensor calibration
• sensor offset
• time for maintenance
• alarm reset (manually or automatically)
• reset to factory settings.
Fig. 12 Menu structure for setup menu
*) These submenus are only needed when changing sensor type.
The sensors for Multilift MD and MLD are already calibrated.
For more information, see service instructions.
TM05 1808 3811
*)
L_01 Start level [mm]
Setup menu
180
250
315
3.8
I_02 Rated current [A]
T_01 Stop delay [sec.]
T_02 Start delay [sec.]
2
0
T_03 Alarm delay [sec.] 5
S00, S01
S_01 Sensor selection
C_01 Calibration
C_02 Offset 490 (MD),
715 (MLD)
Manual
Automatic
0, 3, 6, 12
EXIT
EXIT Back to main menu
G_01 Reset to factory settings
A_01 Reset alarm
M_01 Maintenance interval [month]

English (GB)
16
6.3 Information menu
All status data and fault indications can be seen in the information
menu. The information menu can be seen in all operating modes
(ON-OFF-AUTO). To open the information menu, mark the
symbol using the button and press the button .
Navigate through the menu by means of the buttons and .
Select the desired menu item by pressing the button .
See also fig. 13.
In the information menu the following data can be read:
• fault indications
• operating hours
• number of starts
• max. measured motor current.
Fig. 13 Menu structure for information menu
TM05 1809 3811
EXIT
EXIT Back to main menu
R_03 Measured max. motor current [A] 3.9
007200
000020
20 faults from 01 to 20
20 F006 …
01 F002
R_02 Impulse counter
R_01 Hour counter
F_01 Fault LOG
Information menu

English (GB)
17
6.4 Description of fault indications
If a fault occurs, the symbol will be visible, an audible alarm will be given by the buzzer and the fault code will be written by means of
the 14-segment characters in the display. To see the kind of fault, if it is automatically reset and the code is not longer visible, open the
fault log (see fig. 13). When you leave the fault log, the symbol will disappear.
The last 20 faults are stored in the fault log as fault codes. The meaning of the fault codes are described in the table below:
Fault
code Meaning Displayed
text
Flashing
symbols
Reset of
fault
indications Description
Auto Man
F001 Phase sequence
failure F001 ●
(Only three-phase pumps)
The phase sequence between control board and power supply is
wrong. See fig. 14.
F002 One phase
missing F002 ●●
(Only three-phase pumps)
One phase is missing.
F003 High liquid level F003 ●●The liquid level is high in relation to preset value.
F004 Sensor failure SENSOR - ●●Sensor signal out of range or lost.
F005 Overtemperature,
pump 1 TEMP ●●
Motor thermal switches connected to the controller will stop
pump 1 in case of overheating.
F006 Overtemperature,
pump 2 TEMP ●●
Motor thermal switches connected to the controller will stop
pump 2 in case of overheating.
F007 Overcurrent,
pump 1 F007 ●Pump 1 is stopped if an overcurrent is measured for a certain
period of time (blockage protection).
F008 Overcurrent,
pump 2 F008 ●Pump 2 is stopped if an overcurrent is measured for a certain
period of time (blockage protection).
F009 Undercurrent,
pump 1 F009 ●●
Pump 1 is stopped if an undercurrent is measured for a certain
period of time (dry running protection).
F010 Undercurrent,
pump 2 F010 ●●
Pump 2 is stopped if an undercurrent is measured for a certain
period of time (dry running protection).
F011 Operating time
exceeded, pump 1 F011 ●●
Pump 1 is stopped if normal operating time of the pump is
exceeded, e.g. due to venting problems of pump housing, closed
discharge valve (forgotten to open it after service/maintenance),
forgotten to switch back to automatic mode, if ON-OFF-AUTO
switch is set to "ON" for service/maintenance. A subsequent
emergency operation starts and stops the pump automatically
until the controller gets a regular stop signal from the sensor.
The controller then switches back to normal operation.
F012 Operating time
exceeded, pump 2 F012 ●●
Pump 2 is stopped if normal operating time of the pump is
exceeded, e.g. due to venting problems of pump housing, closed
discharge valve (forgotten to open it after service/maintenance),
forgotten to switch back to automatic mode, if ON-OFF-AUTO
switch is set to "ON" for service/maintenance. A subsequent
emergency operation starts and stops the pump automatically
until the controller gets a regular stop signal from the sensor.
The controller then switches back to normal operation.
F013 External fault EXT - ●
An external level switch can be connected to the controller to give
an alarm when basement outside the lifting station is flooded by
groundwater or water from burst water pipe.
F014 Battery failure BAT - ●●The battery is empty and must be replaced.
F015
Relay or contactor
does not open,
pump 1
RELAY ●Pump 1 receives a signal to stop, but does not react.
This situation is detected by current measurement.
F016
Relay or contactor
does not close,
pump 1
RELAY Pump 1 receives a signal to start, but does not react.
This situation is detected by current measurement.
F017
Relay or contactor
does not open,
pump 2
RELAY ●Pump 2 receives a signal to stop, but does not react.
This situation is detected by current measurement.
F018
Relay or contactor
does not close,
pump 2
RELAY Pump 2 receives a signal to start, but does not react.
This situation is detected by current measurement.

English (GB)
18
If a fault occurs, the red LED will flash, the symbol will be
visible and the fault will be added to the fault log.
Furthermore,Hthe buzzer will be activated, the symbol will be
visible, the corresponding symbols will flash and the fault code
will be displayed. When the fault has disappeared or has been
removed, the controller will automatically switch to normal
operation again. However, the controller enables resetting of the
fault indication (visible and acoustic alarms) either manually
(Man) or automatically (Auto).
If manual resetting was selected in setup menu, the acoustic
alarm and red LED can be reset by pressing the button .
The fault indication will be reset when the fault has disappeared,
has been removed or the ON-OFF-AUTO switch has been set to
OFF position.
You can get an overview of faults in the fault log in information
menu.
The symbol will be visible as long as the fault log is open.
If automatic resetting was selected in menu setup, the red LED
and the symbol will disappear, and the buzzer will be
deactivated again after the fault has disappeared, has been
removed or the ON-OFF-AUTO switch has been set to OFF
position. However, even if automatic resetting was selected,
some of the fault indications have to be reset manually.
See the table above.
Every 30 minutes the fault indication will be written from the
short-term memory into the long-term memory.
Fig. 14 Changing phases of a three-phase controller with
phase inverter
TM05 3455 0412

English (GB)
19
7. Installation of lifting station
7.1 General description
When installing the Multilift MD or MLD lifting station, make sure
that all local regulations covering venting, access to the stations,
etc. are observed.
7.1.1 Installation sketches
Fig. 15 Installation sketch, Multilift MD
Fig. 16 Installation sketch, Multilift MLD
TM05 1864 3811
8472165
3
TM05 1865 3811
3
8
4
65
Pos. Accessories Product number
1 Socket seal, DN 100 97726942
2 Socket seal, DN 50 98079669
3 Diaphragm pump, 1 1/2" 96003721
4 PVC isolating valve, DN 100 96615831
5 Cast iron isolating valve, DN 80 96002011
6 Gasket kit, DN 80, with bolts, nuts and washers 96001999
7 Inlet disk with socket seal, DN 150, for replacement 98079681
8 Battery kit with 9.6 V battery and connection part 98079682

English (GB)
20
7.2 Guidelines for installation of lifting station
The guidelines for correct mechanical installation of lifting station
are according to EN 12056-4.
See section 7.1.1 Installation sketches.
• Install the lifting station in a properly lit and vented room with
60 cm free space around all parts to be serviced and operated.
• Provide a pump sump below the floor level. If a lifting station is
installed in a basement with the risk of penetrating
groundwater, it is advisable (in certain countries required) to
install a drainage pump in a separate pump sump below floor
level in order to drain the room. See figs 15 and 16.
• All pipe connections must be flexible to reduce resonance.
• Lifting stations must be secured against uplift and twist.
• All discharge pipes from lifting station, diaphragm pump and
drainage pump must have a bend above the local backwater
level. The highest point of the bend/reversed water seal must
be above street level. See figs 15 and 16.
• For discharge pipes, DN 80 and upwards, install an isolating
valve in the discharge pipe. Also provide an isolating valve in
the inlet line.
• Surface water must not be discharged into the lifting station
inside the building. It should have its own pumping station
outside the building.
• Lifting stations must be provided with an approved non-return
valve according to EN 12050-4.
• The volume of the discharge pipe above the non-return-valve
up to the backwater level must be smaller than the effective
tank volume.
• In general, a lifting station for black wastewater must be
vented above roof level. However, it is permitted to lead the
ventilation, as a secondary ventilation, into the main building
ventilation system. Special venting valves (accessory) should
be placed outside the building.
• If the wastewater is discharged into a collecting line, this
collecting line must have a filling ratio of at least h/d = 0.7.
The collecting line must be at least one nominal diameter
bigger after the discharge pipe connection.
• The controller must be placed in a flood safe place and be
equipped with an alarm.
• Use a diaphragm pump for simple, manual draining of the
collecting tank in case of pump failure (not obligatory).
7.3 Procedure for installation of lifting station
7.3.1 Inlet pipe connections, Multilift MD
1. Check the scope of delivery.
For scope of delivery see section 2. Scope of delivery.
2. Prepare the adjustable inlet on the back of Multilift MD.
The turnable inlet disk has a DN 100 inlet and allows the inlet
height to be adjusted to any height between 180 and 315 mm
above floor level. The most common heights, 180, 250 and
315 mm, are marked beside the inlet. See fig. 17. An inlet disk
with a DN 150 inlet is available as an accessory. See fig. 18.
The screws around the outer ring of the inlet disk are not fully
tightened allowing the inlet disk to be turned. This will allow
the inlet to be adjusted to the desired inlet height. When the
desired inlet height has been set, tighten all screws.
All screws must be tightened to max. 9 Nm.
Fig. 17 DN 100 inlet disk, adjustable from 180 to 315 mm
above the floor to the middle of the inlet pipe
Fig. 18 Optional DN 150 inlet disk, adjustable from 207 to
279 mm above the floor to the middle of the inlet pipe
Note
The collecting tank, pump and cables may be
flooded (max. 2 m for 7 days).
Caution
The controller must be installed in a dry and well
ventilated place.
Note
Before connecting Multilift MD, consider that
when turning the inlet disk to fit to the height of
the inlet pipe, the lifting station and the discharge
will move sideways accordingly (max. 72.5 mm).
See fig. 17.
TM05 0351 1011
TM051669 3411