Grundig Discalo CCD 6300 User manual

ǵ
CLOCK
RADIO
WITH CD
Discalo
CCD 6300

20
CARE AND SAFETY______________________________
To ensure that this device provides you with long-term satisfaction and
enjoyment, please observe the following instructions.
This device is designed for the playback of audio signals. Any other use is
expressly prohibited.
Protect the device and the CDs from rain, moisture (dripping or splashing
water), sand and heat, e.g. from heating units.
Make sure there is adequate ventilation when positioning the device. There
must be a free space of at least 10 cm behind the device. Do not place
objects on the ventilation slots.
Do not place any vessels such as vases on the device. Vessels may spill fluid
on the electrical components, thus presenting a safety risk. Do not place any
naked flames such as burning candles on the device.
Bringing the device in from the cold can cause condensation on the CD lens,
which prevents it from playing. Give the device time to warm up.
The CD part contains self-lubricating bearings, which must not be oiled or
greased.
Never open the device casing under any circumstances. Warranty claims
are excluded for damage resulting from improper handling.
Thunderstorms are a danger to all electrical devices. Even if the device is
switched off, it can be damaged by a lightning strike to the mains. Always
remove the mains plug during an electrical storm.
Do not use any cleaning agent, as this may damage the casing. Clean the
device with a clean, moist leather cloth.
Please note when deciding where to put the device that furniture surfaces are
covered by various types of lacquer and plastic, most of which contain
chemical additives. These may cause corrosion to the feet of the device, thus
resulting in stains on the surface of the furniture which can be difficult or
impossible to remove.
General instructions for laser devices
You will find a symbol similar to the one shown here on the bottom of
the device.
CLASS 1 LASER PRODUCT means that the laser is designed in such a
way as to ensure that the maximum permissible emission value cannot
be exceeded under any circumstances.
If operating devices or methods other than those specified here are
employed, it may lead to dangerous exposure to emissions.
Invisible laser radiation is emitted if the CD compartment is opened and
the safety locking mechanism is shorted. Do not expose yourself to this
radiation.
ON FM STEREO PROG. REPEAT RANDOM SLEEP
REPEAT CDMODE SKIP PLAY PAUSE SKIP CDSTOP
ON/OFF SLEEP TIMESET MEMORY CDDISPLAY
NIGHTLIGHT
SONOCLOCKCD
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
FM
ON FM STEREO PROG. REPEAT RANDOM SLEEP
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
FM
ON FM STEREO PROG. REPEAT RANDOM SLEEP
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
FM
SNOOZE
21
SNOOZE
21
SNOOZE
21
10
cm
10
cm
10
cm
10
cm
ON FM STEREO PROG. REPEAT RANDOM SLEEP
REPEAT CDMODE SKIP PLAY PAUSE SKIP CDSTOP
ON/OFF SLEEP TIMESET MEMORY CDDISPLAY
NIGHTLIGHT
SONOCLOCKCD
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
FM
ON FM STEREO PROG. REPEAT RANDOM SLEEP
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
FM
ON FM STEREO PROG. REPEAT RANDOM SLEEP
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
FM
SNOOZE
21
SNOOZE
21
SNOOZE
21
ON FM STEREO PROG. REPEAT RANDOM SLEEP
REPEAT CD MODE SKIP PLAY PAUSE SKIP CDSTOP
ON/OFF SLEEP TIME SET MEMORY CDDISPLAY
NIGHTLIGHT
SONOCLOCKCD
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
FM
ON FM STEREO PROG. REPEAT RANDOM SLEEP
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
FM
ON FM STEREO PROG. REPEAT RANDOM SLEEP
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
FM
SNOOZE
21
! SERVICE !! SERVICE !ERVIC
SNOOZE
21
! SERVICE !! SERVICE !ERVIC
SNOOZE
21
! SERVICE !! SERVICE !
! SERVICE !
°C2h
°C
ON FMSTEREO PROG. REPEAT RANDOM SLEEP
REPEAT CDMODE SKIP PLAY PAUSE SKIP CDSTOP
ON/OFF SLEEP TIME SET MEMORY CDDISPLAY
NIGHTLIGHT
SONOCLOCKCD
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
FM
ON FMSTEREO PROG. REPEAT RANDOM SLEEP
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
FM
ON FMSTEREO PROG. REPEAT RANDOM SLEEP
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
FM
SNOOZE
21
SNOOZE
21
SNOOZE
21
ON FMSTEREO PROG. REPEAT RANDOM SLEEP
CDMODE SKIP PLAY PAUSE SKIP CDSTOP
/OFF SLEEP TIMESET MEMORY CDDISPLAY
NIGHTLIGHT
SONOCLOCKCD
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
ON FMSTEREO PROG. REPEAT RANDOM SLEEP
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
ON FMSTEREO PROG. REPEAT RANDOM SLEEP
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
SNOOZE
2
SNOOZE
2
SNOOZE
2
CD
MW
FM
FMST
BUZZ
MUSIC
OFFON
ADJ
2
ENGLISH
CLASS 1
LASER PRODUCT

ENGLISH
21
PLAY/PAUSE SKIP ST
L
EEP TIME SET MEMORY CD DISPL
A
NIGHT LIGHT
D
iscalo
SKIP STOP
MEMORY CD DISPLAY
REPEAT CD MODE
S
ON / OFF
M
ODE SKIP PLAY/PAUSE
SLEEP TIME SET M
NIGHT LIGHT
D
iscalo
Controls
Controls on the top
ON/OFF Switches the device to and from standby mode.
REPEAT Repeats a track or the whole CD.
CD MODE Plays back CD tracks in random order;
switches between playing back a track memory
and normal playback.
I
3SKIP Sets minutes (in conjunction with »TIME SET«).
In CD mode: selects the track played previously
when pressed briefly. If held down searches for a
previous passage.
In alarm mode: sets the alarm time (minutes).
PLAY/PAUSE Starts CD playback.
ıII Pauses playback.
SKIP 4
ISets hours (in conjunction with »TIME SET«).
In CD mode: selects the next track. If held down
searches for the next passage.
In alarm mode: sets the alarm time (hours).
OVERVIEW ___________________________________________
ON FM STEREO PROG. REPEAT RANDOM SLEEP
REPEAT CD MODE SKIP PLAY/PAUSE SKIP STOP
ON / OFF SLEEP TIME SET MEMORY CD DISPLAY
NIGHT LIGHT
Discalo
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
ON FM STEREO PROG. REPEAT RANDOM SLEEP
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
ON FM STEREO PROG. REPEAT RANDOM SLEEP
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
SNOOZE
2
Discalo
1
SNOOZE
2
Discalo
1
SNOOZE
2
Discalo
1
ON FM STEREO PROG. REPEAT RANDOM SLEEP
REPEAT CD MODE SKIP PLAY/PAUSE SKIP STOP
ON / OFF SLEEP TIME SET MEMORY CD DISPLAY
NIGHT LIGHT
D
iscalo
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MH
MW
FM
ON FM STEREO PROG. REPEAT RANDOM SLEEP
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MH
MW
FM
ON FM STEREO PROG. REPEAT RANDOM SLEEP
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MH
MW
FM
2
D
iscalo
1
2
D
iscalo
1
2
D
iscalo
1

22
STOP 7Ends CD playback.
Deletes the track memory for the CD.
CD DISPLAY Briefly switches the display during CD playback
from the time to the track number.
MEMORY Saves a track memory.
TIME SET Activates the time setting.
SLEEP Press briefly displays the current switch-off time.
Press repeatedly: shortens the remaining time until
the device switches off.
NIGHT LIGHT Switches night illumination (on the bottom of the
device) on and off in two brightness levels.
Controls on the sides
TUNING For tuning to radio stations (on the right side of the
device).
VOLUME Adjusts the volume (on the right side of the device).
|
CD MW FM FM STEREO Switches between CD and radio
• • • • mode.
Switches between the FM (VHF) and
MW (medium wave) wavebands.
Switches between FM stereo and mono
reception, right side of the device.
OVERVIEW ____________________________________________
VOLUME
TUNING
CD
MW
FM
FM
S
CD
MW
FM
FMSTEREO
P
LAY/PAUSE SKIP STOP
TIME SET MEMORY CD DISPLAY
H
T LIGHT
FM STEREO PROG. REPEAT RANDOM
SLEEP TIME SET MEMOR
Y
NIGHT LIGHT
FM STEREO PROG. REPEAT RANDOMFM STEREO PROG. REPEAT RANDOM
VOLUME
TUNING
CD
MW
FM
FMSTEREO
OFF
ON
ADJ.
2
OFF ONADJ.
1

ENGLISH
23
0Headphones socket (3.5 mm stereo jack).
Playback via the headphones in stereo, left side of
the device.
e1Activates the alarm time setting and the alarm
OFF ON ADJ function for alarm time 1.
• • • Ends the alarm setting for alarm time 1, left side of
the device.
e2Activates the alarm time setting and the alarm
OFF ON ADJ function for alarm time 2.
• • • Ends the alarm setting for alarm time 2, left side of
the device.
Controls on the back
BUZZER MUSIC Switches between signal tone alarm or alarm with
• • radio or CD.
ÜPower cord.
yWire antenna for FM reception.
Controls on the front
SNOOZE Interrupts the alarm function.
Controls on the bottom
Battery compartment for 9 V back-up battery.
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
SNOOZESNOOZE
SNOOZE
OFF
ON
ADJ.
2
OFFONADJ.
1
S
TEREO
BUZZER
MUSIC
OFFON
ADJ.
1
OFF
ON
ADJ.
2
OFFONADJ.
1
CD
MW
FM
FMSTEREO
BUZZER
MUSIC
OFFON
ADJ.
1
OVERVIEW ____________________________________________

24
The display
0 0 :0 0 Shows the time or the alarm time.
In CD mode: briefly shows the com-
plete number of tracks or the current
track number (in conjunction with
»CD DISPLAY«).
e1 •LED. Indicates that the alarm setting is
activated with alarm time 1.
e2 •LED. Indicates that the alarm setting is activated
with alarm time 2.
MW 540-1600 kHz Tuning scale for the MW and FM wavebands.
FM 88-108 MHz
Note:
The device is equipped with an auto-dimmer, i.e. the brightness of the
display adapts automatically to the lighting in the room by means of a
sensor. The sensor is located on the front of the device.
LEDs
ON •Lights up when the device is switched on.
FM STEREO •Lights up when a stereo channel is received.
PROG. •Flashes while a CD track memory is being saved.
Lights up during CD track memory playback.
REPEAT •Flashes when a single track is repeated.
Lights up when the whole CD is repeated.
RANDOM •Lights up when the tracks on the CD are played
back in random order.
SLEEP •Flashes while the switch-off time is being set.
Lights up when the sleep timer is active.
OVERVIEW ____________________________________________
ON FM STEREO PROG. REPEAT RA
N
ON / OFF SLEEP TIME SET
NIGHT LIGHT
ON FM STEREO PROG. REPEAT RANON FM STEREO PROG. REPEAT RAN
Discalo
1
Discalo
1
Discalo
1
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
540 600 700 800 1000 1300 1600
88 92 96 100 105 108
kHz
MHz
MW
FM
SNOOZE
2
Discalo
1
SNOOZE
2
Discalo
1
SNOOZE
2
D
iscalo
1
T
EREO PROG. REPEAT RANDOM SLEEP
NIGHT LIGHT
TEREO PROG. REPEAT RANDOM SLEEPTEREO PROG. REPEAT RANDOM SLEEP
Discalo Discalo
Discalo
e1
e2000
0:
•
•

ENGLISH
25
Mains operation
Note:
Check that the mains voltage on the type plate (on the bottom of the
device) corresponds to your local mains supply.
If this is not the case, contact your specialist dealer.
1Plug the mains cable into the wall socket.
Caution:
The only way to disconnect the device from the mains supply is to pull
out the plug.
Inserting the back-up battery
During mains operation, the back-up battery ensures that stored settings are
not lost in the case of a power failure or when the device is briefly dis-
connected from the mains.
1Open the battery compartment on the bottom of the device by pressing
the catch marked with an arrow on the drawing and lifting up the cover.
2Before inserting the battery (9 V, 6LF 22) into the cable connection
compartment, note the polarity of the battery.
3Insert the battery.
4Replace the cover of the battery compartment and click the catch into
place.
Note:
Remove the back-up battery when it is flat or when you know that the
device will not be used for a long period of time.
Environmental note:
Batteries, including those which contain no heavy metal, may not be dis-
posed of with household waste. Please dispose of used batteries in an
environmentally sound manner. Find out about the legal regulations
which apply in your area.
POWER SUPPLY___________________________________

26
Additional information for units sold in the UK.
Units sold in the UK are suitable for operation from a 240V ac, 50Hz mains
supply.
The range of multi-system receivers is built to work in most European coun-
tries. However, the mains plug and socket system for the UK differs from
many European countries.
This appliance has been supplied with a fitted, non-removable, approved
converter plug for use in the UK. This converter plug is fitted with a 5A rated
fuse.
In case this appliance is supplied with a moulded 2-pin Euro plug only,
which is unsuitable for UK operation, this must be cut off and immediately
disposed of. An approved 13A, 3-pin UK plug should then be fitted by a
qualified electrician.
Note:
The severed Euro plug must be destroyed to avoid a possible shock
hazard should it be inserted into a socket elsewhere.
If a non-rewireable 3-pin plug or a rewireable 13A (BS1363) 3-pin plug is
used, it must be fitted with a 5A ASTA or BSI approved BS1362 fuse. If any
other type of plug is used it must be protected by a 5A fuse either in the
plug, or at the distribution board. If this type of plug becomes defective,
ensure that the fuse is removed before disposal, to eliminate potential shock
hazard.
If it is necessary to change the fuse in the non-rewireable plug, the correct
type and rating (5A ASTA or BSI approved BS1362) must be used and the
fuse cover must be refitted. If the fuse cover is lost or damaged, the lead and
plug must not be used until a replacement is obtained. Replacement fuse
covers should be obtained from your dealer.
Important:
The wires in the mains lead are colour coded in accordance with the follo-
wing code:
BLUE – NEUTRAL
BROWN – LIVE
As the colours of the wires in the mains lead of your appliance may not cor-
respond with the coloured marking identifying terminals in your plug, pro-
ceed as follows:
Connect the BLUE coloured wire to plug terminal marked with the letter “N”
or coloured black.
Connect the BROWN coloured wire to the plug terminal marked with the let-
ter “L” or coloured red.
In no circumstance must any of the wires be connected to the terminal mar-
ked with the letter “E”, earth symbol “z”, coloured green, or green & yel-
low.
Replacement mains lead sets can be obtained from your local dealer, or by
contacting Grundig Consumer Relations (01788 570088)
Moulded 3-pin lead set, suitable for UK use:
Ref: Leadset UK 8290-991-224
Moulded 2-pin Euro lead set, not suitable for UK use:
Ref: Leadset Euro 8290-991-316
POWER SUPPLY ______________________________________

ENGLISH
27
Setting the clock
When the device is switched on for the first time, »0 :=0« appears in the dis-
play to indicate that the time must be set. The same applies if the device has
been disconnected from the mains and no back-up battery is inserted.
1Set the sliding switches for the alarm function»e1 OFF ON ADJ«
and »e2 OFF ON ADJ« to »OFF«.
2Press »TIME SET« and hold it down.
– Display: the time flashes.
3Press »SKIP 4
I « briefly to set the hours step-by-step or hold it down
to run through the minutes quickly.
4Press »I
3SKIP« briefly to set the minutes step-by-step or hold it
down to run through the minutes quickly.
Note:
When the minute display changes from »59« to »00«, this does not
affect the hour display.
5Release »TIME SET« to conclude the setting.
– Display: the current time.
Setting the alarm times
With this device you can set two alarm times.
1Set the sliding switch »e1 OFF ON ADJ« (left side of the device) to
»ADJ«.
– Display: the last alarm time set flashes.
2Press »SKIP 4
I « (top of the device) briefly to set the hours
step-by-step or hold down to run through the hours continuously.
3Press »I
3SKIP« (top of the device) briefly to set the minutes
step-by-step or hold down to run through the hours continuously.
4To end the setting set the sliding switch »e1 OFF ON ADJ« (on the
left side of the device) to »ON«.
– Display: the LED »e1 •« glows, i.e. the alarm setting with alarm
time 1 is activated.
5To set alarm time 2, repeat steps 1to 4with the sliding switch
»e2 OFF ON ADJ« (left side of the device).
– Display: the LED »e2 •« glows, i.e. the alarm setting with alarm
time 2 is set.
SETTINGS ______________________________________________

28
General functions
Switching on and off
1Press »ON/OFF« to switch on the device from standby mode.
– The »ON •« LED glows.
2Press »ON/OFF« to switch the device to standby mode.
– The »ON •« LED goes out.
Selecting the input source
1Select the input source with »CD MW FM FM STEREO« (right side of
the device).
Adjusting the volume
1Adjust the volume with » VOLUME |« (right side of the device).
Listening with headphones
1 Connect the headphones to the » 0 « socket (ø 3.5 mm) (left side of the
device).
– This automatically switches off the loudspeakers.
Radio operation
For the best FM (VHF) reception, it is sufficient to direct the wire antenna.
The radio has a built-in rod antenna for MW reception. Turn the device aro-
und to direct the antenna.
Selecting the radio input source
1Set the sliding switch »CD MW FM FM STEREO« (right side of the
device) to »MW«, »FM« or »FM STEREO«.
Tuning radio stations
1Select the frequency band (FM or MW) with »CD MW FM FM
STEREO« (right side of the device).
2Set the desired radio station with »TUNING« (right side of the device).
Stereo/mono reception
If the sliding switch »CD MW FM FM STEREO« (on the right side of the
device) is set to »FM STEREO«, the device can receive FM stereo stations. If
this is the case, the »FM STEREO •« LED glows. However, if the signal
from the FM stereo station is weak, you can improve the sound quality by
switching to mono reception.
1Use the sliding switch »CD MW FM FM STEREO« (right side of the
device) to switch from »FM STEREO« to »FM«, i.e. mono.
– The »FM STEREO •« LED goes out.
2Use the sliding switch »CD MW FM FM STEREO« (on the right side
of the device) to switch from »FM« to »FM STEREO«, i.e. stereo.
OPERATION__________________________________________

ENGLISH
29
CD mode
The device is suitable for audio CDs (CD-DA), CD-Rs and CD-RWs with
audio data. Only use CD-DAs which bear the logo shown here. Always
keep the CD compartment closed to prevent dust from collecting on the laser
optics. Do not attach adhesive labels to CDs. Keep the surfaces of CDs clean.
When burning CD-R and CD-RWs with audio files, various problems may
arise which could lead to interference in playback. This can be caused by
faulty software or hardware settings or by the CD being used. Should such
problems arise, contact the customer services of your CD burner or software
manufacturer or look for relevant information, for example, on the Internet.
When you are making audio CDs, observe all legal guidelines and ensure
that the copyright of third parties is not infringed.
Selecting the CD input source
1Switch on the device with »ON/OFF«.
2Set the sliding switch »CD MW FM FM STEREO« (right side of the
device) to »CD«.
3Open the CD compartment by lifting the lid up carefully.
4Insert a CD in the compartment with its label facing upwards.
5Close the lid of the CD compartment carefully.
The device reads the content of the CD. The total number of tracks
appears briefly in the display e.g. »14«, then the time is displayed con-
stantly.
CD playback
1Press »PLAY/PAUSE ıII« to start playback.
– Playback begins with the first track.
– Display: initially the first track number and the time is displayed
constantly.
– Playback stops at the end of the CD.
2Use »PLAY/PAUSE ıII« to switch to playback pause.
– Display: the current track number flashes and then the time is
displayed constantly.
3Press »PLAY/PAUSE ıII« to resume playback.
4Press »STOP 7« to end playback.
Displaying CD information
1During playback, when playback is paused or stopped, press
»CD DISPLAY« to display CD information.
– Display: briefly, the current track, the current track flashing or the total
number of tracks, then the time is displayed constantly.
Repeating the current track
1Press »I
3SKIP« briefly during playback.
– The track is repeated from the beginning.
OPERATION___________________________________________

30
Selecting another track
1During playback, keep pressing »SKIP 4 I « or »I
3SKIP« until the
number of the track you want to hear appears in the display.
– Playback of the selected track starts automatically.
Searching for a passage within a track
1During playback, press »SKIP 4 I « or »I
3SKIP« and hold it
down until you find the passage you want to hear.
– If »SKIP 4 I « or »I
3SKIP« are released, playback starts.
Note:
During the search the volume is reduced.
Calling up the Repeat function
The repeat functions enable you to repeat a single track or the whole CD.
1To repeat a track press »REPEAT« once.
– The »REPEAT •« LED flashes, the current track is repeated con-
stantly.
2To repeat all tracks on the CD press »REPEAT« again.
– The »REPEAT •« LED glows. The entire CD is repeated constantly.
3To cancel this function, press »REPEAT« again.
Playing back tracks in random order
1Press to select the »CD MODE« function.
2Press »PLAY/PAUSE ıII« to start playback.
– The »RANDOM •« LED glows.
– The tracks on the CD are played back in random order.
3To cancel this function, press »CD MODE«.
– The »RANDOM •« LED goes out.
– The tracks are played back in numerical order.
Creating a track memory
This function enables you to store up to 20 tracks on the current CD in a
certain order and then play them back in that sequence. The same track may
be stored more than once.
1Place a CD in the CD compartment.
2When the CD is in the STOP position, select the function with
»MEMORY«.
– Display: »P01«, the »PROG. •« LED flashes.
3Select the track with »SKIP 4
I « or »I
3SKIP«.
– Display: e.g. »03« (for the first selected track) and the »PROG. •«
LEDs flash.
OPERATION___________________________________________

ENGLISH
31
4Press »MEMORY« to save the track.
– Display: »P02«, the »PROG. •« LED flashes.
Note:
Repeat steps 3and 4to program more tracks.
5To start playback of the track memory, press »PLAY/PAUSE ıII«.
– Playback begins with the first programmed track.
Note:
When creating a track memory, if no button is pushed for more than 10
seconds, the system will end the procedure automatically. You then have
to start the procedure again from the beginning.
Changing from the track memory to normal playback
1To end playback of the track memory press »STOP 7«.
2Press »CD MODE«.
– The »PROG. •« LED goes out.
3 Press » PLAY/PAUSE ıII«.
– Normal playback begins at the start of the CD.
Note:
The track memory remains stored when you start normal playback.
Changing from normal playback to the track memory
1Press »STOP 7« to end normal playback.
2Press »CD MODE« twice.
– The »PROG. •« LED glows.
3Press » PLAY/PAUSE ıII«.
– Playback begins with the first programmed track.
Changing the track selection
1To replace a stored track, keep pressing »MEMORY« until its memory
position appears in the display.
2Press »SKIP 4 I « or »I
3SKIP« to select the new track number.
3Press »MEMORY« to store the new track.
Adding tracks
1To add a track, press »MEMORY« repeatedly until the next free
memory position e.g. »P08«, appears.
2Press »SKIP 4 I « or »I
3SKIP« to select the desired track number.
3Press »MEMORY« to store the desired track.
OPERATION___________________________________________

32
Deleting the track memory
1Press »MEMORY« when the CD is in the stop position.
– The »PROG. •« LED flashes.
2Press »STOP 7«.
– The »PROG. •« LED goes out.
Note:
The track memory is also deleted,
– If the CD compartment is opened,
– If the sliding switch »CD MW FM FM STEREO« (right side of the
device) is set to »MW«, »FM« or »FM STEREO«,
– If you pull out the mains cable.
Alarm mode
Selecting the alarm times
1Set the sliding switch »e1 OFF ON ADJ« or »e2 OFF ON ADJ«
(left side of the device) to »ON«.
– Display: The »e1 •« or »e2 •« LED glows;
or
Activate both alarm times by setting the sliding switches »e1 OFF ON
ADJ« and »e2 OFF ON ADJ« (left side of the device) to »ON«.
– Display: The »e1 •« and »e2 •« LEDs glow.
Displaying the alarm times
1Set the sliding switch »e1 OFF ON ADJ« or »e2 OFF ON ADJ«
(left side of the device) to »ADJ«.
– Display: the alarm time most recently set (1 or 2), flashes.
Note:
The sliding switches »e1 OFF ON ADJ« and »e2 OFF ON ADJ«
(left side of the device) should not both be set to »ADJ«, as then the
alarm times cannot be displayed and also cannot be set.
Alarm with signal tone
1Set the sliding switch »BUZZER MUSIC« to »BUZZER«.
2Set the sliding switch »e1 OFF ON ADJ« or »e2 OFF ON ADJ«
(left side of the device) to »ON«.
– Display: The »e1 •« or »e2 •« LED glows.
3Press »ON/OFF« to switch the device to standby mode.
– The »ON •« LED goes out.
– The device switches on at the set alarm times with the alarm signal
(alarm duration 90 minutes).
OPERATION___________________________________________

ENGLISH
33
Alarm with radio station
1Set the sliding switch »BUZZER MUSIC« to »MUSIC«.
2Set the sliding switch »e1 OFF ON ADJ« or »e2 OFF ON ADJ«
(left side of the device) to »ON«.
– Display: The »e1 •« or »e2 •« LED glows.
3Select the frequency band (FM or MW) with »CD MW FM FM
STEREO« (right side of the device).
4Set the desired radio station with »TUNING« (right side of the device).
5Set the desired alarm volume with » VOLUME |« (right side of
the device).
6Press »ON/OFF« to switch the device to standby mode.
– The »ON •« LED goes out.
– The device switches the radio on at the set times (alarm duration 90
minutes).
Alarm with CD
1Set the sliding switch »BUZZER MUSIC« to »MUSIC«.
2Set the sliding switch »e1 OFF ON ADJ« or »e2 OFF ON ADJ«
(left side of the device) to »ON«.
– Display: The »e1 •« or »e2 •« LED glows.
3Set the sliding switch »CD MW FM FM STEREO« (right side of the
device) to »CD«.
4Insert a CD into the CD compartment and set the desired alarm volume
with » VOLUME |« (right side of the device).
5Press »ON/OFF« to switch the device to standby mode.
– The »ON •« LED goes out.
– The device switches CD playback on at the set times (alarm duration
90 minutes).
Alarm with track memory
1Repeat steps 1to 4of the previous section.
2Start playback with »PLAY/PAUSE ıII« and then press »STOP 7«.
3Press »ON/OFF« to switch the device to standby mode.
– The »ON •« LED goes out.
– The device switches CD playback with the stored track memory on at
the set times (alarm duration 90 minutes).
OPERATION___________________________________________

34
Interrupting the alarm
1During the alarm, press »SNOOZE« (at the front of the device).
– The alarm signal (signal tone, radio station or CD) stops.
– The alarm goes on again at 6-minute intervals (alarm duration 90
minutes).
Cancelling the alarm for the day
1Press »ON/OFF« (on the top of the device) while the alarm is
sounding.
– The alarm signal (signal tone, radio station or CD) stops.
– The alarm times set are retained for the next day.
Activating and deactivating the alarm
1To switch off the alarm function set »e1 OFF ON ADJ« or »e2
OFF ON ADJ« (left side of the device) to »OFF«.
– Display: The »e1 •« or »e2 •« LEDs go out.
– The set alarm times are saved.
2To switch on the alarm function, switch »e1 OFF ON ADJ« or »e2
OFF ON ADJ« (left side of the device) from »OFF« to »ON«.
– Display: The »e1 •« or »e2 •« LEDs glow.
OPERATION___________________________________________

ENGLISH
35
Timer mode
The device possesses a sleep timer, which switches it off in radio mode or CD
mode at a preset time. It is possible to set the switch-off time in 30 minute
steps up to 90 minutes.
Setting the sleep timer
1To set the desired switch off time, press »SLEEP« repeatedly.
– Display: » --«, » 90«, » 60« or » 30« (off, 90, 60 or 30 minutes).
– The »SLEEP •« LED flashes.
– After a short time, if selected, the radio switches on and the radio
station selected can be heard.
– The »SLEEP •« LED glows.
– After the selected switch-off time has elapsed, the device switches off
automatically
or
1To set the desired switch off time, press »SLEEP« repeatedly.
– Display: » --«, » 90«, » 60« or » 30« (Off, 90, 60 or 30 minutes).
– The »SLEEP •« LED flashes.
2If CD mode has been selected, start playback with »PLAY/PAUSE ıII«.
– The »SLEEP •« LED glows.
– After the selected switch-off time has elapsed, the device switches off
automatically.
Displaying the switch-off time remaining
1Press »SLEEP« briefly.
– Display: briefly, the switch-off time remaining.
Switching off the sleep timer
1To switch off the sleep timer before the set time, press »ON/OFF«.
– The device switches to stand-by mode.
OPERATION___________________________________________

36
Technical data
This device is noise-suppressed according to the applicable EU directives.
This product fulfils the European directives 89/336/EEC, 73/23/EEC and
93/68/EEC.
This device conforms to the safety regulation DIN EN 60065 (VDE 0860) and
therefore the international safety regulation IEC 60065.
The type plate is located on the bottom of the device.
INFORMATION_____________________________________
Technical data
Power supply:
Mains operation: 230 V, 50 Hz
Back-up battery 1 x 9 V, 6LF 22
Max. power consumption: < 4 W (operation), < 3 W (standby)
Output: DIN 45324, 10% THD 2 x 1.5 W
Radio unit:
Frequency band FM 87.5 ...108.0 MHz
MW 520 ... 1610 kHz
CD unit:
Frequency response 20 Hz ... 20 kHz
Noise voltage ratio ≥65 dB
Dimensions and weight: W x H x L 144 x 194 x 181 mm
Weight approx. 1.7 kg
Technical and design modifications reserved.

ENGLISH
37
Troubleshooting
If a fault occurs, first refer to this information before you take the device for
repair.
If you are unable to rectify the fault using the information given here, contact
your local dealer or service specialist.
Under no circumstances should you attempt to repair the device yourself, as
this would invalidate the guarantee.
INFORMATION _______________________________________
PROBLEM
GENERAL
INFORMATION
No sound
The device does not
respond to button
commands
RADIO
Poor radio reception
CD
Playback will not start
The CD player skips
tracks
CD-Rs or CD-RWs
are not being played
back, or being
played back incor-
rectly
POSSIBLE CAUSE
Volume is set too low or
headphones are connected,
mains cable is not correctly
connected
Static electrical discharge
Weak radio antenna signal
Interference from electrical
devices such as televisions,
video recorders, computers,
neon lamps, thermostats
or motors
The CD is damaged or dirty
A stored track memory is being
played
The RANDOM function is acti-
vated
Faulty software or hardware
settings for burning, or the CD
being used is faulty
REMEDY
Increase the volume,
unplug headphones
Connect the mains cable
properly
Switch off device,
disconnect mains cable and
plug it in again after a few
seconds
FM (VHF): redirect the wire
antenna
Switch from stereo to mono
reception
MW: turn whole device
Keep radio recorder away
from electrical devices
Replace or clean the CD
Switch to normal playback
or delete the track memory
Switch off the RANDOM
function
Check the components of
your CD burner/burner
software or change the CD
you are using

Grundig AG •Beuthener Str. 41 • D-90471 Nürnberg • http://www.grundig.com 3/12 72011 403 7500