Grundig SCC 240 User manual

CLOCK RADIO
SCC 240
SCN 230
Sonoclock 2000
Sonoclock 2500 BT
SV
EN DE FR
PL TR
IT DA
ES

3 ENGLISH
___________________________________________________________
TIME
TUN+/AL 2
TUN-/AL 1
ON/OFF
SLEEP DIMMER
SNOOZE
USB
(SCC 240)
TUNING+/HR
TUNING-/MIN
PRESET

4 ENGLISH
DEUTSCH 05-15
ENGLISH 16-26
FRANÇAIS 27-37
ITALIANO 38-48
DANSK 93-103
SVENSKA 104-114
POLSKI 115 - 125
ESPAÑOL 61-72
TÜRKÇE 61-72

ENGLISH 5
7 Note, prolonged listen-
ing at loud volumes with
the earphones can dam-
age your hearing.
7
Do not expose the back-up bat-
tery to extreme heat, caused for
example by direct sunlight, heat-
ers or fire.
7
Never open the device casing.
No warranty claims are accepted
for damage caused by incorrect
handling.
7
The type plate is located on the
bottom of the device.
7
Protect the device from moisture
(water drops or splashes). Do not
place any vessels such as vases
on the device. These may be
knocked over and spill fluid on
the electri cal components, thus
presenting a safety risk.
7
Do not expose the device to ex-
treme heat, caused for example
by direct sunlight, heator fire.
SAFETY AND SET-UP ____________________________
7
This device is designed for the
playback of audio signals. Any
other use is expressly prohibited.
7
Protect the device from moisture
(water drops or splashes). Do not
place any vessels such as vases on
the device. These may be knocked
over and spill fluid on the electri-
cal components, thus presenting a
safety risk.
7
Do not place any naked flames
such as candles on the device.
7
Make sure the device is adequate-
ly ventilated. Do not cover the
ventilation slots with newspapers,
table cloths, curtains, etc.
7
When deciding where to place
the device, please note that furni-
ture surfaces are covered by vari-
ous types of varnish and plastic,
most of which contain chemical
additives. These additives can cor-
rode the device supports, leaving
residues on the furniture surfaces
which can be difficult or impossi-
ble to remove.
7
Do not use any cleaning agent,
as this may damage the casing.
Clean the device with a clean,
moist leather cloth.

6 ENGLISH
VOLUME -/
AL 1 Adjusts the volume.
Indicates that the
alarm setting is acti-
vated with alarm time
1.
VOLUME +/
AL 2 Adjusts the volume.
ON/OFF Switches the device
on or off.
SLEEP Activates the
sleep timer.
To display the current
sleep timer setting.
SNOOZE Interrupts the
alarm function.
Displays the seconds.
DIMMER Sliding switch,
switches the display
between two bright-
ness levels.
Controls on the back
Ü USB Power-out cable.
Wire antenna for FM
reception.
OVERVIEW ______________________________________
See the figure on page 3.
Controls on the top
TUNING-/
MIN
For tuning to radio sta-
tions.
For setting the min-
utes. Press briefly to
change the minutes
step-by-step. Hold
down to change the
minutes continuously.
TUNING+/
HR
For tuning to radio sta-
tions.
For setting the hours.
Press briefly to change
the hour step-by-step.
Hold down to change
the hour continuously.
PRESET Displays the alarm
times.
TIME Press and hold down:
to set the time.

ENGLISH 7
OVERVIEW ______________________________________
Controls on the bottom
Battery compartment for 5V back-up
battery.
The display
AL 1 Displays that the alarm is
activated with a signal
tone or radio for alarm
time 1.
AL 2 Displays that the alarm
is activated with a
signal tone or radio
for alarm time 2.

8 ENGLISH
Inserting the back-up
battery
During mains operation, the back-up
battery ensures that stored settings
are not lost in the case of a power
failure or when the device is briefly
disconnected from the mains.
1 Open the battery compartment lid
by pressing on the arrow and pus-
hing down the lid.
2 When inserting the battery (micro
batteries, 2 x 1.5 V, LR3/ UM 4/
AAA), observe the polarity marked
on the base of the battery compart-
ment.
Note:
7 Remove the back-up battery
when it is flat or when you know
that the device will not be used
for a long period of time.
Environmental note:
7 Batteries, including those which
do not contain heavy metal,
should not be disposed of
with household waste. Always
dispose of used batteries in
accordance with local environ-
mental regulations.
POWER SUPPLY ________________________________
Mains operation
Check that the mains voltage on
the type plate (on the bottom of the
device) corresponds to your local
mains supply. If this is not the case,
contact your specialist dealer.
1 Plug the mains cable into the so-
cket (230V~, 50/60 Hz).
Caution:
7 The device is connected to the
mains with the power plug. To
fully disconnect the device from
the mains, pull out the plug.
7 The mains plug is used to dis-
connect the device. It shall
remain readily operable and
should not be obstructed during
intended use.

ENGLISH 9
The installed microprocessor of the
radio-controlled clock processes the
received time telegrams and controls
the quartz clock fully automatically.
After the clock is first activated, the
DCF synchronisation is performed
immediately and subsequently every
day at 2 am and 3 am. Depending
on the point of reception, synchroni-
sation can take several minutes. Dur-
ing this process, the » « display
flashes, if the signal is strong enough,
in a 1 second rhythm of the received
time telegram. After synchronization
has taken place, the » « display
begins to light up. If the » « dis-
play disappear, the synchronization
was not successful.
In addition to the advantages of the
time precision and the exact, to-the-
second wake-up and alarm signal,
your radio clock sets itself fully auto-
matically from winter time to summer
time.
SETTINGS ________________________________________
Radio-controlled clock
With your built-in radio-controlled
clock, you are in possession of an
absolutely precise alarm and meet-
ing clock which is automatically set
to the radio-transmitted time signals of
the most precise clock in the world:
the atomic clock of the Physikalisch-
Technischen Bundesanstalt (PTB – the
German national metrology institute).
This clock is so precise that in 1 mil-
lion years a deviation of 1 second
can be expected.
Your radio-controlled alarm clock
receives “time telegrams” via long
wave 77.5 kHz from the time signal
transmitter DCF 77, located in Main-
flingen (24 km south-east of Frank-
furt/Main). This time signal transmitter
has a range of 1500 km.
The device receives the station
DCF 77 free of charge via the con-
nected DCF 77 antenna everywhere,
where a sufficient long wave recep-
tion is possible with a good portable
radio. In many cases, your radio
clock receives the time telegrams
from a considerable distance from
the station; however, the local recep-
tion quality plays a significant role
here.

10 ENGLISH
Setting time and day of the
week
If the device has been switched on
for the first time – if no time signal
has been received – »0:00« ap-
pears in the display as a sign that
the time has to be set. The same ap-
plies after a power failure or if the
device has been disconnected from
the mains supply and no back-up
battery has been inserted.
1 Press »TUNING+/HR« briefly to
set the hours step-by-step or hold
down to run through the hours
continuously.
2 Press »TUNING-/MIN« briefly
to set the minutes step-by-step or
hold down to run through the min-
utes continuously.
Notes:
7 When the minute display chang-
es from »59« to »00«, this does
not affect the hour display.
7 The device saves the set time
automatically after 10 seconds.
3 To set the day of the week, press
»TIME« and »SET« at the same
time.
– Display: for example, the day of
the week »d1« = Monday.
SETTINGS ________________________________________
4 Set the day of the week (»1« =
Monday, »2«, »3«, »4«, »5«,
»6« or »7« = Sunday) using
»TUNING+/HR« or
»TUNING-/MIN«.
– The device saves the selected
day of the week automatically
after 5 seconds.
Note:
7 Display the selected day of the
week and press »SNOOZE«
longer than 3 seconds and hold
it pressed.
Setting the time zone
If you use the device outside of the
Central European Time Zone (CET),
you can correct the time by +/– 2
hours.
1 Press »TIME ZONE/WEC« keep
pressed for approximately 2 sec-
onds.
– Display: »00«, »:« flashes.
2 Set the time zone with »TUN-
ING+/HR« or »TUNING-/
MIN« (Scale: »00«, »01«, »02«,
»-02« and »-01«).
– Display: e.g. »02«.

ENGLISH 11
Note:
7 If a back-up battery has not been
inserted, the time is automatically
reset by DCF time synchronisa-
tion as long as the DCF recep-
tion is strong enough. Alarm time
and time zone synchronisation
are each reset to the values
»00:00« and »00«. Please note
that, in this case, you may be
wakened at the wrong time.
Setting alarm time 1
1 Press and hold »VOLUME -/AL
1«.
– Display: the last alarm time set
flash alternately.
2 Press »TUNING+/HR« briefly to
set the hours step-by-step or hold
down to run through the hours
continuously.
3 Press »TUNING-/MIN« briefly
to set the minutes step-by-step or
hold down to run through the min-
utes continuously.
– The device saves the set alarm
time automatically after 10 sec-
onds.
– The device wakes you up at the
set time with the alarm signal of
your choice.
SETTINGS ________________________________________
Setting alarm time 2
1 Press »VOLUME +/AL 2« three
times.
– Display: the last alarm time set
flash alternately.
2 Press »TUNING+/HR« briefly to
set the hours step-by-step or hold
down to run through the hours
continuously.
3 Press »TUNING-/MIN« briefly
to set the minutes step-by-step or
hold down to run through the min-
utes continuously.
– The device saves the set alarm
time automatically after 10 sec-
onds.
– The device wakes you up at the
set time with the alarm signal of
your choice.

12 ENGLISH
Saving radio stations on
program-places
You can save this radio-program on
10 program places.
1 Set the radio station by pressing and
holding down »TUNING+/HR«
or »TUNING-/MIN«.
– The radio station search starts and
stops at the next station with a
good reception signal;
or keep pressing »TUNING+/
HR« or »TUNING-/MIN« un-
til you reach the frequency you
want.
– Each time you press the button, the
frequency changes by 50 Hz.
2 Press »PRESET« longer.
3 Select the program-place with »PRE-
SET«.
4 Confirm with »PRESET«.
Adjusting the volume
1 Adjust the volume by pressing
»VOLUME -/AL 1« or »VOLU-
ME +/AL 2«.
OPERATION _____________________________________
Switching on and off
1 Press » ON/OFF« to switch on the
device from standby mode.
2 Press »ON/OFF« to switch the
device to standby mode.
Radio mode
For the best possible FM (VHF) re-
ception, it is sufficient to align the
wire antenna accordingly.
Tuning to radio stations
1 Set the radio station by pressing
»ON/OFF«.
– Keep pressing »TUNING+/
HR« or »TUNING-/MIN« un-
til you reach the frequency you
want.
– Each time you press the button, the
frequency changes by 50 Hz.

ENGLISH 13
Alarm mode
The device has a dynamic alarm tone
that starts at a low volume and reach-
es its maximum volume within 30 to
45 seconds.
Viewing the alarm time
1 Press »VOLUME -/AL 1« ones
(for alarm time 1) or press »VO-
LUME +/AL 2« (for alarm time
2).
– Display: the last set alarm time
1 or 2, the LED »AL 1 « or
»AL 2 « flashes.
Note:
7 If no other button is pressed, the
device switches back automati-
cally to the current time after
10 seconds.
Alarm with radio station
1 Press »ON/OFF« to switch on the
device.
2 Select the radio station using the
»-TUNING+« dial.
3 Adjust the alarm volume by press-
ing »TUNING+/HR« or »TUN-
ING-/MIN«.
OPERATION _____________________________________
4 Set the radio station you want as
an alarm signal (» «), and press
»AL1« or »AL 2« twice.
– Display: the corresponding LED
»AL 1 « or »AL 2 «
lights up.
5 Press »ON/OFF« to switch off the
device.
– The device wakes you up at the
set time with the radio station
(alarm duration is 59 minutes).
Alarm with signal tone
1 Press »ON/OFF« to switch off
the device.
2 Set the signal tone alarm signal
(» «), and press »AL 1« or »AL 2«
once.
– The device wakes you up at
the set time with the signal tone
(alarm duration is 59 minutes).
Interrupting the alarm
1 Press »SNOOZE« while the
alarm is sounding.
– The alarm signal (radio station
or signal tone) stops.
– The alarm goes on again at
9 minute intervals (alarm dura-
tion is 59 minutes).

14 ENGLISH
Deactivating the sleep timer
1 To deactivate the sleep timer ear-
ly, press »ON/OFF«.
– The device switches to stand-by.
Note:
7 The device realize the switch-off
time and offer this time for the
next using like a preselection.
Cancelling the alarm for the
day
1 Press »ON/OFF« while the
alarm is sounding.
– The alarm signal (radio station
or signal tone) stops, the alarm
remains at the set time for the
next day.
Timer mode
The device has a sleep timer, which
switches it off in radio mode at a pre-
set time. The switch-off time can be set
to between 1 minute and 1 hour and
59 minutes and then stays saved.
Activating the sleep timer
1 Press »SLEEP« to switch on the
device.
– Display: the switch-off time
»0:59« (for 59 minutes).
– You will hear the selected radio
station.
2 Set the selected switch-off time
with »HOUR/VOL+« or »MIN/
VOL-« step-by-step (press briefly)
or continuously (hold down).
– After the selected switch-off time
has elapsed, the device switch-
es off automatically.
3 Display the remaining switch-off
time with »SLEEP«.
OPERATION _____________________________________

ENGLISH 15
BLUETOOTH MODE ______________________
Bluetooth device compat-
ibility
Your Sonoclock 2500 BT connects
with all Bluetooth devices that sup-
port the A2DP profile including the
most smartphones, laptops and tab-
lets.
Selecting the input source
Bluetooth
1 Select the input source Bluetooth
with »Mode/AL«.
– Display: »Bluetooth« and
»Searching«.
Pairing Bluetooth device
1 Activate on the Bluetooth device
the Bluetooth function.
2 Start on the Bluetooth device the
search function.
– After a short period of time, your
Grundig Sonoclock 2500 is dis-
played on the Bluetooth device.
3 Select the Grundig Sonoclock
2500 on the Bluetooth device
and connect it.
4 Once the Bluetooth device is
connected to your device, the
Sonoclock 2500 BT will display
»Bluetooth« and »Con-
nected«.
Note:
7 Although the Sonoclock 2500
BT can only stream audio from
one device at a time, it is capa-
ble of being paired with up to
eight devices.
Connecting a paired Blue-
tooth Device
Notes:
7 You will only need to pair your
Bluetooth device with the unit
one time.
7 The next time your Bluetooth de-
vice and the Sonoclock 2500
BT are in range of each other,
and the Bluetooth feature is
turned on, they will automati-
cally connect.
7 The Sonoclock 2500 BT will only
automatically connect to the last
Bluetooth Device it was connect-
ed to.
7 If your paired device does not
automatically connect, navigate
to the Bluetooth menu on your
device and select the unit from
the list.

16 ENGLISH
Play Audio signal from your
Bluetooth device
1 Start playback on the Bluetooth
Device.
2 Adjust the volume using »– +«.
3 End playback on the Bluetooth
Device.
Notes:
7 Various functions may also be
controlled from the Sonoclock
2500 BT. Select Playback-
Pause using »5+ eII« , press
»5+ eII« again to resume
playback; select previous title
by pressing »r«, select next title
by pressing »e«.
7 Keep in mind that depending on
the used Bluetooth device and
the structual conditions the wire-
less range can be up to 9 m.
Disconnect the Bluetooth de-
vice
1 Switch off the Bluetooth function at
the Bluetooth device or long press
»OK/i« button.
– Display changes to: »Search-
ing«.
Reconnecting the Bluetooth
device
1 If you move out of range or turn
off the Bluetooth feature on your
device, the unit will disconnect
from your device.
2 To reconnect, simply access the
Bluetooth Manager on your Blue-
tooth device and select the Grun-
dig Sonoclock 2500.
Note:
7 In case of the registered Grun-
dig Sonoclock 2500 cannot
connect to the Bluetooth de-
vice again, please remove the
Grundig Sonoclock 2500 from
the Bluetooth device list, search
and connect again.
Automatic shutdown
If Bluetooth is selected as input source
and no Bluetooth device is connect-
ed, the Sonoclock 2500 BT switches
automatically to Stand-by mode after
15 minutes.
BLUETOOTH MODE ______________________

ENGLISH 17
Do not dispose of the packaging mate-
rials together with the domestic or other
wastes. Take them to the packaging ma-
terial collection points designated by the
local authorities.
Technical data
This device is noise-
suppressed according
to the applicable EU
directives. This product
fulfils the European directives 2014/53/
EU, 2009/125/EC and 2011/65/EU.
You can find the CE declaration of con-
formity for the device in the form of a pdf
file on the Grundig Homepage
www.grundig.com/downloads/doc.
Power supply:
AC 100 - 240 V~, 50/60 Hz (adaptor)
Max. power consumption:
< 3 W (operation),
< 1 W (standby)
Output:
USB host (For SCC 240 only):
5V power-out
Back up battery:
Back up DC Batt: 1 × 9 V IEC 6 LF22
Frequency bands:
FM 87.5 ...108.0 MHz
Circuit features:
Loudspeaker: 2 1/4 inch
Output Power: 1.5 W
INFORMATION _________________________________
Compliance with the WEEE
Directive and Disposing of
the Waste Product:
This product complies with EU WEEE
Directive (2012/19/EU). This product
bears a classification symbol for waste
electrical and electronic equipment
(WEEE).
This product has been manu-
factured with high quality
parts and materials which
can be reused and are suita-
ble for recycling. Do not dis-
pose of the waste product
with normal domestic and other wastes at
the end of its service life. Take it to the
collection center for the recycling of elec-
trical and electronic equipment. Please
consult your local authorities to learn
about these collection centers.
Compliance with RoHS
Directive
The product you have purchased com-
plies with EU RoHS Directive (2011/65/
EU). It does not contain harmful and
prohibited materials specified in the Di-
rective.
Package information
Packaging materials of the
product are manufactured
from recyclable materials in
accordance with our Na-
tional Environment Regulations.

18 ENGLISH
Dimensions:
W x H x L 95 x 150 x 75 mm
Weight: 565 g
Technical and design modifications re-
served.
INFORMATION _________________________________

Grundig Intermedia GmbH
Thomas-Edison-Platz 3
D-63263 Neu-Isenburg
www.grundig.com
18/35