Grundig Sonoclock 1000 User manual

CLOCK RADIO
SCN 120
SCN 130
Sonoclock 1000
Sonoclock 1500
SV
EN DE FR
PL TR
IT DA
ES

3 ENGLISH
___________________________________________________________
TIME
TUNING+/HR
TUNING-/MIN
PRESET
TUN+/AL 2
TUN-/AL 1
ON/OFF
SLEEP DIMMER
SNOOZE
USB
(SCN 130)

4 ENGLISH
DEUTSCH 05-15
ENGLISH 16-26
FRANÇAIS 27-37
ITALIANO 38-48
DANSK 93-103
SVENSKA 104-114
POLSKI 115 - 125
ESPAÑOL 61-72
TÜRKÇE 61-72

ENGLISH 5
7 Note, prolonged listen-
ing at loud volumes with
the earphones can dam-
age your hearing.
7
Do not expose the back-up bat-
tery to extreme heat, caused for
example by direct sunlight, heat-
ers or fire.
7
Never open the device casing.
No warranty claims are accepted
for damage caused by incorrect
handling.
7
The type plate is located on the
bottom of the device.
7
Protect the device from moisture
(water drops or splashes). Do not
place any vessels such as vases
on the device. These may be
knocked over and spill fluid on
the electri cal components, thus
presenting a safety risk.
7
Do not expose the device to ex-
treme heat, caused for example
by direct sunlight, heator fire.
SAFETY AND SET-UP ____________________________
7
This device is designed for the
playback of audio signals. Any
other use is expressly prohibited.
7
Protect the device from moisture
(water drops or splashes). Do not
place any vessels such as vases on
the device. These may be knocked
over and spill fluid on the electri-
cal components, thus presenting a
safety risk.
7
Do not place any naked flames
such as candles on the device.
7
Make sure the device is adequate-
ly ventilated. Do not cover the
ventilation slots with newspapers,
table cloths, curtains, etc.
7
When deciding where to place
the device, please note that furni-
ture surfaces are covered by vari-
ous types of varnish and plastic,
most of which contain chemical
additives. These additives can cor-
rode the device supports, leaving
residues on the furniture surfaces
which can be difficult or impossi-
ble to remove.
7
Do not use any cleaning agent,
as this may damage the casing.
Clean the device with a clean,
moist leather cloth.

6 ENGLISH
VOLUME -/
AL 1 Adjusts the volume.
Indicates that the
alarm setting is acti-
vated with alarm time
1.
VOLUME +/
AL 2 Adjusts the volume.
ON/OFF Switches the device
on or off.
SLEEP Activates the
sleep timer.
To display the current
sleep timer setting.
SNOOZE Interrupts the
alarm function.
Displays the seconds.
DIMMER Sliding switch,
switches the display
between two bright-
ness levels.
Controls on the back
Ü USB Power-out cable.
Wire antenna for FM
reception.
OVERVIEW ______________________________________
See the figure on page 3.
Controls on the top
TUNING-/
MIN
For tuning to radio sta-
tions.
For setting the min-
utes. Press briefly to
change the minutes
step-by-step. Hold
down to change the
minutes continuously.
TUNING+/
HR
For tuning to radio sta-
tions.
For setting the hours.
Press briefly to change
the hour step-by-step.
Hold down to change
the hour continuously.
PRESET Displays the alarm
times.
TIME Press and hold down:
to set the time.

ENGLISH 7
OVERVIEW ______________________________________
Controls on the bottom
Battery compartment for 5V back-up
battery.
The display
AL 1 Displays that the alarm is
activated with a signal
tone or radio for alarm
time 1.
AL 2 Displays that the alarm
is activated with a
signal tone or radio
for alarm time 2.

8 ENGLISH
Inserting the back-up
battery
During mains operation, the back-up
battery ensures that stored settings
are not lost in the case of a power
failure or when the device is briefly
disconnected from the mains.
1 Open the battery compartment lid
by pressing on the arrow and pus-
hing down the lid.
2 When inserting the battery (micro
batteries, 2 x 1.5 V, LR3/ UM 4/
AAA), observe the polarity marked
on the base of the battery compart-
ment.
Note:
7 Remove the back-up battery
when it is flat or when you know
that the device will not be used
for a long period of time.
Environmental note:
7 Batteries, including those which
do not contain heavy metal,
should not be disposed of
with household waste. Always
dispose of used batteries in
accordance with local environ-
mental regulations.
POWER SUPPLY ________________________________
Mains operation
Check that the mains voltage on
the type plate (on the bottom of the
device) corresponds to your local
mains supply. If this is not the case,
contact your specialist dealer.
1 Plug the mains cable into the so-
cket (230V~, 50/60 Hz).
Caution:
7 The device is connected to the
mains with the power plug. To
fully disconnect the device from
the mains, pull out the plug.
7 The mains plug is used to dis-
connect the device. It shall
remain readily operable and
should not be obstructed during
intended use.

ENGLISH 9
The installed microprocessor of the
radio-controlled clock processes the
received time telegrams and controls
the quartz clock fully automatically.
After the clock is first activated, the
DCF synchronisation is performed
immediately and subsequently every
day at 2 am and 3 am. Depending
on the point of reception, synchroni-
sation can take several minutes. Dur-
ing this process, the » « display
flashes, if the signal is strong enough,
in a 1 second rhythm of the received
time telegram. After synchronization
has taken place, the » « display
begins to light up. If the » « dis-
play disappear, the synchronization
was not successful.
In addition to the advantages of the
time precision and the exact, to-the-
second wake-up and alarm signal,
your radio clock sets itself fully auto-
matically from winter time to summer
time.
SETTINGS ________________________________________
Radio-controlled clock
With your built-in radio-controlled
clock, you are in possession of an
absolutely precise alarm and meet-
ing clock which is automatically set
to the radio-transmitted time signals of
the most precise clock in the world:
the atomic clock of the Physikalisch-
Technischen Bundesanstalt (PTB – the
German national metrology institute).
This clock is so precise that in 1 mil-
lion years a deviation of 1 second
can be expected.
Your radio-controlled alarm clock
receives “time telegrams” via long
wave 77.5 kHz from the time signal
transmitter DCF 77, located in Main-
flingen (24 km south-east of Frank-
furt/Main). This time signal transmitter
has a range of 1500 km.
The device receives the station
DCF 77 free of charge via the con-
nected DCF 77 antenna everywhere,
where a sufficient long wave recep-
tion is possible with a good portable
radio. In many cases, your radio
clock receives the time telegrams
from a considerable distance from
the station; however, the local recep-
tion quality plays a significant role
here.

10 ENGLISH
Setting time and day of the
week
If the device has been switched on
for the first time – if no time signal
has been received – »0:00« ap-
pears in the display as a sign that
the time has to be set. The same ap-
plies after a power failure or if the
device has been disconnected from
the mains supply and no back-up
battery has been inserted.
1 Press »TUNING+/HR« briefly to
set the hours step-by-step or hold
down to run through the hours
continuously.
2 Press »TUNING-/MIN« briefly
to set the minutes step-by-step or
hold down to run through the min-
utes continuously.
Notes:
7 When the minute display chang-
es from »59« to »00«, this does
not affect the hour display.
7 The device saves the set time
automatically after 10 seconds.
3 To set the day of the week, press
»TIME« and »SET« at the same
time.
– Display: for example, the day of
the week »d1« = Monday.
SETTINGS ________________________________________
4 Set the day of the week (»1« =
Monday, »2«, »3«, »4«, »5«,
»6« or »7« = Sunday) using
»TUNING+/HR« or
»TUNING-/MIN«.
– The device saves the selected
day of the week automatically
after 5 seconds.
Note:
7 Display the selected day of the
week and press »SNOOZE«
longer than 3 seconds and hold
it pressed.
Setting the time zone
If you use the device outside of the
Central European Time Zone (CET),
you can correct the time by +/– 2
hours.
1 Press »TIME ZONE/WEC« keep
pressed for approximately 2 sec-
onds.
– Display: »00«, »:« flashes.
2 Set the time zone with »TUN-
ING+/HR« or »TUNING-/
MIN« (Scale: »00«, »01«, »02«,
»-02« and »-01«).
– Display: e.g. »02«.