Grundig Sonoclock 420 User manual

ELECTRONIC CLOCK RADIO
SONOCLOCK 420
1

2
3 Sicherheit/Informationen 8 Radio-Betrieb
4 Auf einen Blick 8 Weck-Betrieb
6 Stromversorgung 10 Timer-Betrieb
7Installation 84 Service
11 Safety/Information 17 Radio mode
12 Overview 17 Alarm mode
14 Current supply 19 Timer mode
16 Installation 84 Service
20 Sécurité/Informations 25 Fonction radio
21 Vue d’ensemble 25 Fonction réveil
23 Alimentation en courant 27 Fonction horloge
24 Installation 84 Service après-vente
28 Sicurezza/Informazioni 33 Funzionamento radio
29 In breve 33 Funzionamento sveglia
31 Alimentazione elettrica 35 Funzionamento Timer
32 Installazione 84 Servizio
36 Segurança/Informações 41 Função rádio
37 Vista geral 41 Função despertar
39 Alimentação de corrente 43 Função timer
40 Instalação 84 Assistência a clientes
44 Seguridad/Información 49 Modo radio
45 Vista general 49 Modo despertador
47 Alimentación de corriente 51 Modo timer
48 Instalación 84 Servicio
52 Veiligheid/informatie 57 Radiofunctie
53 In een oogopslag 57 Alarmfunctie
55 Stroomtoevoer 59 Timer-mode
56 Installeren 84 Service
60 Sikkerhed/informationer 65 Radiofunktion
61 Kort oversigt 65 Vækkefunktion
63 Strømforsyning 67 Timerfunktion
64 Installation 84 Service
68 Säkerhet/Information 73 Radioanvändning
69 En överblick 73 Väckningsfunktionen
71 Strömförsörjning 75 Timerfunktioner
72 Installation 84 Service
76 Turvatoimet/tietoja 81 Radiokäyttö
77 Yleiskatsaus 81 Herätystoiminto
79 Käyttövirta 83 Ajastintoiminto
80 Ohjelmointi 84 Service
___________________________________________________________________
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
PORTUGUÊS
ESPAÑOL
NEDERLANDS
DANSK
SVENSKA
SUOMI

ENGLISH
11
Safety
To ensure that this device provides you with long-term satisfaction and ent-
ertainment, please observe the following instructions:
This device is designed for the playback of audio signals.
Any other use is expressly prohibited.
Protect the device from moisture.
Please note when setting up the device, that furniture surfaces are covered
by various types of lacquer and plastic, most of which contain chemical
additives. These additives can, among other things, corrode the material of
the device supports, resulting in residues on the furniture surfaces which are
difficult or impossible to remove.
Do not use any cleaning agent, as this may damage the casing. Clean the
device with a clean, moist leather cloth.
Do not open the device. The manufacturer accepts no liability for damage
resulting from improper handling.
The identification plate is located at the bottom of the device.
Information
This device is noise-suppressed according to the applicable EC guidelines.
This product fulfils the European guidelines 89/336/EEC, 73/23/EEC and
93/68/EEC.
This device corresponds to the safety regulation VDE 0860 and thus the
international safety regulation IEC 65.
Technical data
Current supply: 230 Volt, 50/60 Hz
Output: DIN 45324, 10% THD 800 mW
Frequency range: FM 87.5 ...108.0 MHz
Dimensions and weight W x H x L 185 x 70 x 170 mm
Weight approx. 0.7 kg
Environment
The packing material for your device has been kept to a minimum.
It can be divided into two separate materials: Cardboard (box) and poly-
ethylene (bag).
Please observe the local regulations for disposing of the packing material.
Technical and optical modifications reserved!
SAFETY, INFORMATION_____________________
ENGLISH

12
1...5 and Channel positions, press once for channel position
6...10 1 ... 5, press twice for channel position 6 ... 10.
Display Displays various information, such as station frequen-
cy, time, day, alarm setting.
MEMORY Saves a radio station on a channel position.
ALARM 1 Select the desired alarm type:
ALARM 2 (e1or e2) = wake with signal tone, (¤1or ¤2)
= wake with radio station.
To set the alarm time, press and hold down
»ALARM 1« or »ALARM 2« and set the alarm
time with »+« or »–«.
WEC Blocks the alarm function during the weekend.
SLEEP Pressing once activates the sleep timer;
each repeated pressing reduces the operating time by
10 minutes (from 90 to 10 minutes).
SNOOZE Device activated: interrupts the alarm for approx.
5 minutes.
Interrupts the sleep timer.
Device switched off: to set the day of the week, hold
down »SNOOZE« and set the day with »+« or »–«.
OVERVIEW ___________________________________________
ON/OFF
TIME
TUNING
1
SONOCLOCK 420
5
4
3
2
1
10
9
8
7
6
S
L
E
E
P
SNOOZE
A
L
A
R
M
2
A
L
A
R
M
1
M
E
M
O
R
Y
W
E
C
1...5
6...10
Anzeige
ALARM 1 ALARM 2
WEC SLEEP
SNOOZE
MEMORY
+ TUNING –
TIME
ON/OFF
VOLUME

ENGLISH
13
+ TUNING – For setting the radio station;
for setting the time, day of the week and alarm time.
ON/OFF Switching on/off;
terminates alarm for the day;
terminates the reminder timer.
TIME To set the time, hold down »TIME« and set the time
with »+« or »–«.
VOLUME For setting the volume.
UUHeadphone jack, for connecting a headphone set with
a jack plug (ø 3.5 mm).
The device loudspeaker is switched off.
Back of the device
ÜÜMains cable.
Line antennae.
Bottom of the device
RESET Returns the device to its original setting.
Battery compartment for back-up batteries.
OVERVIEW____________________________________________

14
Connecting the mains cable
Note:
Check if the mains voltage on the identification plate (at the bottom of
the device) corresponds to the local mains voltage.
If this is not the case, contact your dealer.
1Insert the mains cable in the socket (230 V~, 50/60 Hz).
Caution:
The only way to isolate the device from the mains supply is to pull the
plug.
Insert back-up batteries
If there is a power failure, the clock time and alarm time, as well as the
channel memory of the device are saved by the back-up batteries.
Radio mode and alarm mode cannot be used, the display is not illuminated,
however the clock time is displayed.
1Open the battery compartment by pressing the marked surface and
pushing back the cover.
2Insert two batteries (micro type, for example, UM4, R 03, 2x1.5V),
observing the polarity marked at the bottom of the battery compart-
ment.
Note:
We recommend that you replace the back-up batteries after approxi-
mately 1 year.
Remove the batteries when they are flat, or when the device is dis-
connected from the mains for an extended period.
There is no liability for damage resulting from flat batteries.
Environmental note:
Batteries, including those which are heavy metal-free, may not be dis-
posed of along with household waste. Please ensure the environmental-
ly sound disposal of used batteries, e.g. via public recycling sites. Find
out about the legal regulations which apply in your area.
Reset
If the electronic system of your device becomes blocked (as the result of sta-
tic electricity from the floor carpet or storms, for example), the device can be
reset to its original condition.
1Press »RESET« (at the bottom of the casing) with a sharp object.
– Time, day, alarm time and radio settings are deleted.
CURRENT SUPPLY________________________________
RESET

ENGLISH
15
Important notes for users in the U.K.
Mains plug
This apparatus is fitted with an approved moulded 13 Amp plug. To change
a fuse in this type of plug proceed as follows:
1Remove fuse cover and fuse.
2Fix new fuse which should be a BS1362 5 Amp, A.S.T.A. or BSI appro-
ved type.
3Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off
and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 5 Amp. If a
plug without a fuse is used, the fuse at the distribution board should not be
greater than 5 Amp.
Note:
The severed plug must be disposed to avoid a possible shock hazard
should it be inserted into a 13 Amp socket elsewhere.
How to connect plug
The wires in the mains lead are coloured with the following code: blue =
neutral (N), brown = live (L).
As these colours may not correspond with the colour markings identifying
the terminals in your plug, proceed as follows:
1Connect the blue wire to the terminal marked N or coloured black.
2Connect the brown wire to the terminal marked L or coloured red.
3Do not connect either wire to the earth terminal in the plug, marked E
(or e) or coloured green (or green and yellow).
Before replacing the plug cover, make certain that the cord grip is clamped
over the sheath oft the lead – not simply over the two wires.
CURRENT SUPPLY____________________________________

16
Setting the time
1After the device has been connected to the mains, you must set the time
and the day.
– Display: »88« and » «, the time »0:00« flashes.
2Press and hold down »TIME«.
3Set the time with »+« or »–« (TUNING).
– When »+« or »–« (TUNING) are held down, the time can be set
more quickly.
Setting the day
1Press »SNOOZE« and hold down.
2Set the day with »+« or »–« (TUNING).
Setting radio stations
There are 10 channel positions available for radio stations.
1Switch on Sonoclock with the »ON/OFF« button.
– Display: »•«.
2Begin station search by pressing and holding down »+« or »–«
(TUNING).
– The search stops as soon as a radio station with a sufficiently strong
signal is found.
– You can also set the frequency step-by-step (50 kHz) by briefly press-
ing »+« or »–« (TUNING).
3Save radio station by pressing »MEMORY« (»M« flashes in the dis-
play), select the desired channel position within 8 seconds with
»1 ... 10« and confirm with »MEMORY«.
– Press buttons »1 ... 10« once for channel positions 1 ... 5, and twice
for channel positions 6 ... 10.
– Display: the frequency of the selected channel position. In the dis-
play, »M« is illuminated.
4To set further radio stations, repeat procedure from pt. 2.
Note:
If no channel position is selected within 8 seconds, the device interrupts
the setting procedure. Start again at pt. 3.
SUN
INSTALLATION _____________________________________
SUNWEC
●88000: .
MONSUNWEC
●88930: .
SUNWEC
●88930: .
MONSUNWEC
●8FM MHz
8875:.
MONSUNWEC
●8FM MHz
8882:.
MONSUNWEC
●8FM
M
MHz
I
8882:.

ENGLISH
17
RADIO MODE_______________________________________
Note:
Each time a button is pressed, the display of your device is illuminated
for 8 seconds.
Radio reception
When the device is switched off, the display shows the current time and
day.
1Switch on the device with the »ON/OFF« button.
– Display: »FM«, »•«, the station frequency and the day of the week,
quickly followed by the current time.
– The previous channel position is automatically selected.
2Select channel position with the »1 ... 10« buttons.
– Press »1 ... 10« once for channel positions 1 ... 5, and twice for
channel positions 6 ... 10.
3Switch off the device with »ON/OFF«.
– Display: »88«, quickly followed by the current time and the day.
Note:
To display channel position and frequency, briefly press »+« or »–«
(TUNING).
Adjusting the volume
1 Adjust the volume with »VOLUME «.
ALARM MODE______________________________________
Setting alarm time and type
You can enter two different alarm times and select between two different
alarm types.
Setting the alarm time
1Enter the first alarm time by pressing and holding down the
»ALARM 1« button.
– Display: the set alarm time.
2Set the desired alarm time with »+« or »–« (TUNING).
3Release »ALARM 1«.
Note:
Repeat procedure for the second alarm time, using »ALARM 2«.
WEDT UEMO NSUNWEC
●8FM
M
MHz
3
8979:.
WEDT UEMO NSUNWEC
●812 25: .
WEDT UEMO NSUNWEC
●8FM
M
MHz
2
8922:.
WEDT UEMO NSUNWEC
●8
¤18000: .
WEDT UEMO NSUNWEC
●8
¤18600: .

18
Alarm with radio station
1Switch on the device with »ON/OFF«.
2Select channel position with the »1 ... 10« buttons, adjust volume with
»VOLUME«.
3Switch off the device with »ON/OFF«.
4Activate first alarm time by pressing »ALARM 1« until »¤1«
appears in the display.
– The device switches to alarm time 1 and switches off again after
90 minutes.
– While the alarm sounds, »¤1« flashes in the display.
Note:
Repeat procedure for the second alarm time, using »ALARM 2«.
Alarm with signal tone
Your device is equipped with a dynamic signal tone; this means the volume
of the signal tone becomes increasingly louder as it sounds.
1Switch off the device with »ON/OFF«.
2Activate first alarm time by pressing »ALARM 1« until »e1«
appears in the display.
– The device switches to alarm time 1; the signal tone becomes increa-
singly loud. The signal tone is switched off after a maximum of
90 minutes.
– While the alarm sounds, »e1« flashes in the display.
Note:
Repeat procedure for the second alarm time, using »ALARM 2«.
The signal tones for alarm time 1 and alarm time 2 are different.
Check the alarm time
You can check both alarm times.
1Switch off the device with »ON/OFF«.
2Press »ALARM 1« once.
– Display: alarm type, alarm time 1.
3Press »ALARM 2« again.
– Display: alarm type, alarm time 2.
ALARM MODE________________________________________
WEDT UEMO NSUNWEC
●8
¤18600: .
WEDT UEMO NSUNWEC
ee1
●88600: .