Technical Data
Power input : 230 Vac ±15%,50-60Hz Standard.
Data storage : Flash APROM memory.
Relay output : UV-C SPDT relay 8(1)A, 250V AC
Panel Cutout : 29 X 71mm
Housing : Black ABS Plastic, Auto-extinguish
Front Cover : Polycarbonate Plastic
Dimensions : Frontal : 78 X 36mm, Depth : 59mm
Mounting : Flush panel mounting with fasteners
Protection : IP65 Front (with gasket)
Connections : Screw terminal blocks. < 2.5sq mm terminal
only.
Display : 2 X 17mm 7 segment display
: 2 LED Icons for Indication
Storage Temp. : -25.0ºC to 60.0ºC (non-condensing)
Operating Temp. : 0ºC to 60ºC (non-condensing)
Timer Range : 0 to 99 Min/sec (as per setting)
Digital Input (Potential Free) : Door Limit Switch
Buzzer : Internal
Operating Humidity : 20% to 85% (non-condensing)
Resolution : +/- 1 Min/Sec (Configurable)
Working Logic & Functions
Blinking
for 3 sec
Door
Open
Timer is over & Relay output is OFF.
Door is open & Relay output is OFF.
Display & LED Indications
LED Status Description
Timer is started & Relay output is ON.
ON
OFF
Blinking
Timer is stopped & Relay output
is OFF.
Timer is on hold & Relay output is
OFF.
UV-Light
Time Delay
To change Timer Measurement unit
To change Timer reset mode at Door Open
To change the timer unit, touch “ ” key for 2 sec. Display
will show “ ” if unit is set to minutes & Display will show “ ”
if unit is set to seconds. Timer will be set and display will show
“0”. Factory set value is in seconds.
+
To change the timer reset mode, touch “ ” key for 10 sec.
Display will show “ ” if timer reset mode is set to Manual &
Display will show “ ” if timer reset mode is Auto at Door Close.
+
Ordering Information
Sr. No. Timer Model
No. Brief Description Buzzer
Door Input
Sensing - DI
1.
2.
GS-UV-C-2
GS-UV-C-3
Included
Included
Internal
Internal
36x78mm,
8(1)A/250vac,
Relay based Timer
in Horizontal
Display
Orientation. Red
Color.
36x78mm,
8(1)A/250vac,
Relay based Timer
in Vertical Display
Orientation. Red
Color.
Disclaimer: This manual & its contents remain the sole property of Selector India
and shall not be reproduced or distributed without authorization. Although great care
has been taken in the preparation of this document, the company or its vendors in no
event will be liable for direct, indirect, special, incidental or consequential damage
arising out of the use or inability to use the product or documentation, even if advised
of the possibility of such damages. No part of this manual may be reproduced or
transmitted in any form or by any means without the prior written permission of the
company. Selector India, reserves the right to make and changes or improvements
without prior notice.
Warranty: This product is warranted against defects in materials and workmanship
for a period of one year from the date of purchase. During the warranty period,
product determined by us to be defective in form or function will be repaired or, at our
option, replaced at no charge. This warranty does not apply if the product has been
damaged by accident, abuse, and misuse or as a result of service or modification
other than by the company. This warranty is in lieu of any other warranty expressed
or implied. In no event shall the company be held liable for incidental or
consequential damages, including lost revenue or lost business opportunity arising
from the purchase of this product.
00 / 12.08.2020
3. To start the timer again touch “ ” key.
4. Timer is running & if user has touched key, then timer will
stop. Timer will reset and display will show last saved value
that is 10.
1. Use key to set value from 0 to 99. When set to ‘0’
timer function is inactive.
2. Example: Timer count value is set to 10, touch the “ ”
and timer will start countdown & Relay will switch ON. After
every minute or second, as per unit setting, display count will
decrease by 1. Once timer is over, display will blink “ ” for
3sec & Relay will be OFF. Timer will reset & Display will show
last set value of timer that is “10”.
5. Timer can Start and Hold by “ ” key.
7. When door is closed, Relay will start auto if timer reset mode is
set to auto else user has to start manually by “ ” key.
8. Buzzer will turn ON when timer is over & display will flash “ ”
for 3 seconds.
6. Relay will switch OFF when Door is open.
/
iii. Timer is over.
v. Door is open.
iv. Timer Unit is changed.
i. Timer value is changed.
ii. Timer is reset by key.
Relay will be OFF when below conditions occurs:
Note:
