GSL electronics VDBC1224-20-NG-2 User manual

Chemistry Selection in Doubler Mode
27V Output
28V Output
25V Output
30A
50A
BROWN
Floating/No Connection
WHITE
GREEN
BLACK
RED
ORANGE
24V
LOAD
To Ignition Switch of vehicle
BLUE
Page 1 of 2
Model:
VDBC1224-20-NG-2
Next Generation DC to DC
Booster Battery Charger / Doubler
12VDC to 24VDC 20A
Operating Instructions
Please read these instructions before use
The VDBC1224-20-NG-2 joins our new NG series of units that uses the next
generation topology reducing the size and increasing the output power
compared to its previous VI and BC series of units.
In an extremely compact package (373cm³) the VDBC1224-20-NG-2
combines thefeatures of a doubler and a battery charger in a weather,
dust and vibration resistant package.
Features include:
• Dual Option - 3-Stage 24V Battery Charger or Voltage Doubler
• Peak Output : 20A
• Selectable output voltages for Lithium (29.6V/27.6V), Sealed Lead
Acid (28.4V/27V), Vented Lead Acid (29.2V / 27V) or Doubler (25V/27V/28V)
• Over Current and Temperature protections for extra product reliability.
• High Efciency : Typical >95%
• Precise under voltage protection : No need for external isolator.
• Latched overload protection for preventing dangerously charging faulty batteries
• Remote LED indication for battery charge status.
• Very low standby current: <3mA
1. Disconnect the battery supply.
2. The following connection sequence is to be followed: Ground (BLACK), Output (BROWN), Input (RED), LED (GREEN),
Chemistry/Output Selection (Orange), ON/OFF (Blue) and Mode Select (WHITE). The BLACK and BROWN wires are to be connected as
directly as possible to the 12V input battery.
3. The unit is protected from weather and dust but do not pressure wash or mount to areas that will be submerged. Avoid locations such
as fuel lines or where external heat is produced e.g. exhaust system or where the batteries are located.
4. Chose a position with good ventilation where air can pass freely around the unit.
5. Ensure the unit is protected from sources of contamination e.g. oil, grease and dust.
6. Ensure that the unit is installed away from any ammable fumes, liquids or materials.
VDBC1224-20-NG-2
Note: Before installation the user shall determine the suitability of the product to ensure correct application.
Wiring Diagram - For Doubler Setup
LED
Caution: For all Floating or wires that are not used - Please isolate
or tape up wires to avoid accidental connection.
More information https://www.caravansplus.com.au

To Ignition Switch of vehicle
BROWN GREEN
BLACK
RED
ORANGE
WHITE - To Ground
BLUE
Chemistry Selection
LED
24V
30A
50A
Page 2 of 2
Model:
VDBC1224-20-NG-2
Unit 2, 110 Station Road, Seven Hills ,NSW, 2147, Australia
VDBC1224-20-NG-2-R5
Wiring Diagram - For Charger Setup
Warranty Conditions: Our products come with guarantees that cannot be excluded under the Australian Consumer Law.
The customer is entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.
The customer is also entitled to have the products repaired or replaced if the products fail to be of acceptable quality and the failure does not amount to a major failure.
GSL Electronics (GSL) warrants that its products will, under normal use and service, be free of defects in material and workmanship for a period of two (2) years from
the date of the original purchase by the customer as marked on the customer’s original invoice.
Please refer to our website for full warranty and return information which can be found at http://www.gsl.com.au/faq.html
Check out our website for more of your Power Conversion Needs
http://www.gsl.com.au
www.gsl.com.au
Remember to add us to your favorites
and/or bookmark us too!
Caution: For all Floating or wires that are not
used - Please isolate or tape up
wires to avoid accidental connection.
More information https://www.caravansplus.com.au