Gu electronic Audi 4g+ pas tdc2 User manual

Instruction Manual

Audi 4G+ PAS TDC2 for AUDI , Q7

GU Electronic

INDEX

Specifications

1. Main Spec. ----------------------------------

2. Diagram -------------------------------------

3. Components --------------------------------

4. Components (Option) ----------------------

5. Exterior --------------------------------------

Settings

1. Dip Switch ----------------------------------

2. Original button -----------------------------

3. Touch Control ------------------------------

4. OSD Menu ----------------------------------

Installation

1. CAN Connection ----------------------------

2. Caution --------------------------------------

GU Electronic

Specification

1. Main spec.

1-1 Input Spec. (MULTI VIDEO INTERFACE)

- 1 x Digital RGB Input (Navigation System output)

- 1 x Analog RGB Input (Navigation System output)

- 1 x CVBS(REAR CAMERA) Input. (Rear camera source)

- 1 x CVBS(FRONT CAMERA) Input. (Front camera source)

- 1 x LVDS Input. (Car Command System)

- 1 x Capacitive Touch Screen

1-2 Output Spec.

- 1 x LCD Output (LCD Operation)

- 1 x Resistive Touch Output

1-3 Power Spec.

- Input Power : 8VDC ~ 24VDC

- Consumption Power : 12Watt, Max

1-4 Switch Input mode

- Possible to switch input mode through original button

2. Features

- Possible to install capacitive touch screen with frame (Option)

- Possible to register IR code of DVD/DTV

- Display dynamic PAS(Parking assistance system)

- Easy installation with plug & play power/LVDS cable

GU Electronic

Specification

3. Diagram

Scaler

(PIP)

MCU EEPROM

CAN

RECEIVER

LVDS

TX RELAY

REAR CAMERA

POWER

LVDS

CAR

COMMAND

SYSTEM

CAN

RGB+Sync

REAR CAMERA

DIGITAL RGB LVDS

INTERFACE

CAR

TFT-LCD

LVDS

GU Electronic

Specification

4. Components

Power Cable 1EA

LVDS Cable 1EA

RGB Navi Cable 1EA

Touch Cable(KD-900) 1EA

GU Electronic

Specification

4. Components (Option)

Touch Board

Touch Cable

Q7 8.2”

Capacitive Touch Screen

A4 8.2”

Capacitive Touch Screen

①: remove the protective plastic

②: replace the OEM bracket with

the Provided bracket

Q7 8.2”

Plastic Bracket

①②

Specification

5. Exterior

159mm

25mm

83mm

GU Electronic

*NAVI Connect

① R DATA (Red)

② G DATA (Green)

③ B DATA (Blue)

④ SYNC (White)

⑤ GND (Black)

⑥ DMB IR (Green)

⑦ DVD IR (Orange)

①②③④⑤⑥⑦

*POWER Connect

① ACC(Yellow)

②REAR_POWER (Red)

③CAN-HIGH (Orange)

④CAN-LOW (Green)

⑤CAN-HIGH (Purple)

⑥CAN-LOW (White)

⑦GND (Black)

①②③④⑤⑥⑦

Settings

1. Dip Switch

* ON : DOWN , OFF : UP

GU Electronic

NO. Function Selection

1 NAVI ON : Skipping NAVI

OFF : Display

2 DVB-T(AV1) ON : Skipping DVB-T(AV1)

OFF : Display

3 DVD(AV2) ON : Skipping DVD(AV2)

OFF : Display

4 N.C

Car model

ON : AUDI A4 / Q7 8.2 “

6 ON : AUDI A4 / Q7 8.2 “

7 ON : AUDI A4 / Q7 8.2 “

8 OFF : AUDI A4 / Q7 8.2 “

* Example

AUDI A4 / Q7 8.2 “

※ Both of DTV(A1) and DVD(A2) are through Front input

Settings

2. Original button - Switching mode

[Audi 2016year A3/A4/Q7]

GU Electronic

※ It is necessary to connect CAN wire to use the original button

※ You can choose the Steering wheel type from the OSD Menu (p.15)

PUSH

- NAVI: Switching mode

- RADIO, TEL, MEDIA: Switching to OEM directly

- PUSH: Display DVB-T & DVD UI ICON

-⤿, ⤾: Control the DVB-T & DVD UI ICON

Steering wheel - 1

(Switching mode )

Steering wheel - 2

(Switching mode)

2. Original button – TOUCH

- Touch calibration

Touch the OEM screen in any mode more

than 7sec. for calibration

(This function can be activated only one time

after switching mode)

Touch the “+” correctly

- DVB-T/DVD Control

Press Touch (Anywhere) Press Icon

GU Electronic

Settings

DVB-T

DVD

2. Original button - DVB-T, DVD Menu

*Control the OSD menu by OEM button

[Type -1] [Type -2]

•DVD

[POWER][SCAN] [Ch+] [Ch-]

[POEWER][MENU]

[RETURN][USB]

[stop]

[Play/Pause]

[Audio]

•DTV (Select the type of I-con)

[FR]

[FF]

[Ch+]

[Ch-]

[Right]

[Left]

[POWER]

[DISC UP]

[DISC DOWN]

[Play next

chapter]

[Play previous

chapter]

GU Electronic

※ To use this function, It is necessary to offer the remote IR code to manufacturer

or setting OSD IR – Ctrl（P. 20）

Settings

MENU : Press long(7sec) - Activating OSD menu

Press short - Exit

① PUSH : Selection

② Moving up, Increasing value

③ Moving down, Decreasing value

④ Moving from third menu to first menu in order

⑤ Moving from first menu to third menu in order

⑥ Moving up, Increasing value

⑦ Moving down, Decreasing value

Mode state

Second menu Third menu

First menu

GU Electronic

Settings

2. Original button – OSD Menu

*Control the OSD menu by OEM button

⑥

② ⑤

PUSH

①

⑦

③

④

Settings

GU Electronic

Config - NAVI-RGB : Setup for the type of RGB

Config - DVB-T(DMB) : Setup for the type of DVB-T(DMB)

Config - DVD : Setup for the type of DVD

Reset : Reset all value

3. OSD Menu

※ Press “MENU” button on Key board

Settings

GU Electronic

Option

•RearCam-Type : Setup for rear camera

ExtDevice - External rear camera

OEM - Original camera

•RearCam-Power : Setup for Rear VCC wire in power cable

ON - +12V out always (current consumption : 200mA)

AUTO - +12V out in rear mode only (200mA)

OFF - Power OFF

•RearCam-Det : Setup for Rear detection

P>>, GEAR : by CAN wire

Ext Wire : by 12V wire

Setting to display screen when switching to D gear from R gear (Refer to picture on P.16)

P>> : OEM type - When switching to D gear from R gear , press

the activated “P“ button or driving up 20km to display AV/RGB/OEM screen

GEAR : Normal type -

When switching to the D gear from the R gear, The

AV/RGB/OEM screen is shown right away

•AV Mode : When the “REAR TYPE” is OEM

ON : Using the “Rear input” as AV3

OFF : Not used

•FrontCam-Type : Setup for front camera

ExtDevice - External rear camera

OEM - Original carmer

3. OSD Menu

※ Press “MENU” button on Key board

Settings

GU Electronic

Option

•FrontCam-Power : Setup for Front VCC wire in power cable

ON - +12V out always (current consumption : 200mA)

AUTO - +12V out in rear mode only (200mA)

OFF - Power OFF

•FrontCam-Det : Setup for front detection

ExtDevice - External rear camera (N.C)

OEM - Original camera

•FrontCam-RcvOpt : Selecting time of displaying Front camera before switching to RGB,

DVD, OEM from Rear

•SteeringMode : Setting Handle wheel button (Refer.9)

ON- MODE or NAV

OFF- OFF

OEM

NAVI

AV1(DVB-T)

AV2(DVD)

REAR FRONT

OEM

NAVI

AV1(DVB-T)

AV2(DVD)

Select time of display

1~30 second

3. OSD Menu

※ Press “MENU” button on Key board

Settings

- NAVI(RGB) Image / Screen

- DVD, DVBT, NAVI-AV, REAR, FRONT Image

GU Electronic

3. OSD Menu

※ Press “MENU” button on Key board

Settings

-Parking guide line ON/OFF

Selecting a use of packing guide line

(OSD Menu – Parking – Line display

– ON or OFF)

Parking Line - ON

GU Electronic

Gear

Car Audio Box Button

1. OEM type : When switching to “D” gear from “R” gear , Press the “P“ button

or drive up 20km to display AV/RGB/OEM screen

2. Normal type : When switching to “D” gear from “R” gear, The AV/RGB/OEM screen is

shown right away

-Setting for displaying external screen when switching to “D” gear

from “R” gear(p.15)

3. OSD Menu – Parking mode

※ Press “MENU” button on Key board

Settings

- Adjust the position of Parking guide line

- Transparency – Setting to the transparency of Parking guide line

-Warning Language for rear screen

Selecting a type of language (OSD Menu – Parking – Warning Lang)

GU Electronic

Possible to adjust the position of line

by OEM Button in Horizontal / Vertical menu

※ Pressing this Horizontal / Vertical menu,

The OSD screen automatically disappears.

Please adjust from the parking line Screen.

3. OSD Menu

※ Press “MENU” button on Key board

Down

Left Right

- OSD

MENU Horizontal

OSD

IR-Ctrl

Utility

Horizontal

Vertical

Display

Transparency

Language English

10s

- IR – Ctrl (p.20)

- Utility

MENU Utility

OSD

IR-Ctrl

Utility

Factory Reset

Version

Execute Cancel

ADPc10KRX - 170409

•Utilityy– INTERFACE SOFTWARE

•OSD – Horizontal

•OSD – Vertical

•OSD – Display : Setting time for displaying OSD menu

•OSD – Transparency

•OSD – Language : Setting language of ODS menu

GU Electronic

Settings

3. OSD Menu

※ Press “MENU” button on Key board

※ Caution

•Delete :

ALL Clear – Delete all value

Clr – Delete one button’s Value

•Play/Pause：

To use button, Please register

the IR code in power / Pause menu

separately

- IR Ctrl

MENU DVB-T(DMB) DVD

OSD

IR-Ctrl

Utility

DVB- T

DVD

Sel Learn Cancel

User

Sys

MENU DVB-T(DMB) DVD

OSD

IR-Ctrl

Utility

ALL - Clear

POWER

SCAN

CH+

CH-

____ _____

MENU DVB-T(DMB) DVD

OSD

IR-Ctrl

Utility

New Code :

Cfm Code :

____ _____

Save Clr Cancel

① ②

③

① Select IR Ctrl àDVB/DVD/DVR

àLearn to register IR code

② All Clear : Remove all value of

Remote control registered before

Select one of the buttons registering

to move on to next step

③ Press a button on the remote control

of DVD/DTV then the IR code will be

appeared on “New code” menu. Press the

same button one more time to confirm

the IR code. (Cfm code = confirm code)

4. OSD Menu – Register IR code

※ Press “MENU” button on OSD Key board

GU Electronic

Settings

Table of contents

Other GU Electronic Car Video System manuals

GU Electronic

GU Electronic Chrysler-CIP-2014-D User manual

GU Electronic

GU Electronic CAMRY2016 User manual

GU Electronic

GU Electronic Audi-R-PAS-D User manual

GU Electronic Audi 4G+ PAS TDC2 User manual

Popular Car Video System manuals by other brands