GU Electronic CAMRY2016 User manual

Instruction Manual
Toyota Camry2016 for Camry 2016y 8”

GU Electronic
INDEX
Specifications
1. Main Spec. ------------------------------------
2. Diagram ---------------------------------------
3. Components ----------------------------------
4. Exterior ----------------------------------------
Settings
1. Dip Switch -------------------------------------
2. Original button -------------------------------
3. Touch Control ---------------------------------
4. OSD Menu ------------------------------------
Installation
1. Diagram ---------------------------------------
2. LVDS Connection -----------------------------
3. Fixing an interface board --------------------
4. Caution ----------------------------------------
2
3
4
5
6
7
8
10
12
18
19
20
21

GU Electronic
1. Main spec.
1. Input Spec. (MULTI VIDEO INTERFACE)
- 1 x Digital RGB Input (Navigation System output)
- 1 x Analog RGB Input (Navigation System output)
- 2 x A/V Input (External video source)
- 1 x CVBS(REAR CAMERA) Input. (Rear camera source)
- 1 x CVBS(FRONT CAMERA) Input. (Front camera source)
- 1 x LVDS Input. (Car Command System)
2. Output Spec.
- 1 x LCD Output (LCD Operation)
- 1 x Analog Touch Output (Navigation System input)
1-3 Power Spec.
- Input Power : 8VDC ~ 24VDC
- Consumption Power : 12Watt, Max
1-4 Switch Input mode
- Possible to switch input mode through original button
2. Features
- Possible to register IR code of DVD/DTV
- Easy installation
3
Specification

GU Electronic 4
3. Diagram
Scaler
(PIP)
MCU
LVDS
TX
INTERFACE
CAR
COMMAND
SYSTEM
LVDS
CAN
EEPROM
CAN
RECEIVER
LVDS
TX
CAR
TFT-LCD
LVDS
RX
RELAY
REAR CAMERA
POWER
REAR CAMERA
COMPOSITE
Analog RGB
NAVIGATION
SYSTEM
CVBS1
CVBS2 MUX
Digital RGB
FRONT CAMERA
DAC
Specification

GU Electronic 5
OSD 1EA
TOUCH 1EA
POWER 1EA
LVDS 1EA
Specification
A/V 1EA
Bolt 6mm 4 EA
NAVI 1EA
RGB 1EA
UART TX Cable 1EA

175mm
21mm
83mm
6
Specification
*POWER Connect
① ACC (Red)
② BATTERY (Yellow)
③ IE+ (Orange)
④ IE- (Green)
⑤ KEY (Blue)
⑥ REAR_DETECT (Brown)
⑦ REAR_POWER (Red)
⑧ GND (Black)
① ② ③ ④ ⑤ ⑥ ⑦ ⑧
*NAVI Connect
① R DATA (Red)
② G DATA (Green)
③ B DATA (Blue)
④ SYNC (White)
⑤ GND (Black)
⑥ DMB IR (Green)
⑦ DVD IR (Orange)
①②③④⑤⑥⑦
*NAVI-POWER Connect
① Battery (Yellow)
② ACC (Red)
③ NC (Blue)
④ GND (Black)
① ② ③ ④
GU Electronic

NO. Function Selection
1 NAVI ON : Skip
OFF : Display
2 DVB-T(AV1) ON : Skip
OFF : Display
3 DVD(AV2) ON : Skip
OFF : Display
4
N.C
ON: -
5ON: -
6ON: -
7ON: FUJISTEN, Panasonic
8ON:RAV4, Panasonic
7
Settings
1. Dip Switch
* ON : DOWN , OFF : UP
CAMRY 2016y RAV4
GU Electronic
ON 1 2 3 4 5 6 7 8
FUJISTEN
ON 1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
Panasonic
ON 1 2 3 4 5 6 7 8

8
Settings
2. OEM button (FUJISTEN) - Switching mode
√
GU Electronic
- HOME, ☏ -> Switching to OEM directly
NAVI
OEM
DVB-T DVD
- MODE S/W, ☏ -> Switching mode

9
Settings
2. OEM button (CAMRY) - Switching mode
GU Electronic
- MAP, DEST -> Switching mode

10
GU Electronic
Settings
3. Touch screen - Switching mode
※ It is necessary to install provided capacitive touch film on OEM monitor
※ It is needed to select “HomeIcon-ON” in Option menu to activate HOME
button
Press “HOME” button to activate OSD for mode change
Press long : Switching to OEM
directly
Press short : Activating OSD menu
※ The position of Home button can be moved by dragging
HomIcon – “ON”
OSD Menu for switching
input mode

11
2. Touch calibration, DVB-T, DVD Control
•DVD
[stop]
[Play/Pause]
[Audio]
•DTV
[FR]
[FF]
[POWER]
[DISC UP]
[DISC DOWN]
[Play next chapter]
[Play previous chapter]
Settings
※ To use this function, It is necessary to offer the remote IR code to manufacturer or setting OSD IR – Ctrl（P. 17）
[POWER] [SCAN]
[Channel up] [Channel down]
GU Electronic
Touch OEM screen in any mode more than
7sec. For calibration
(This function can be activated only one time
after switching mode)
Touch the “+” correctly

3. OSD Key board
① MENU : Activating OSD Menu
② SEL : Selection
③ Up : Moving upward / increasing value
④ Down : Moving downward / decreasing value
MENU SEL UP DOWN
①②③ ④
4. OSD Menu
※Press “MENU” button on the Key board
12
Config - NAVI-RGB : Setup for the type of RGB
Config - DVB-T(DMB) : Setup for the type of RGB
Config – DVD : Setup for the type of DVD
Reset : Reset all value
Settings
GU Electronic

13
4. OSD Menu
※Press “MENU” button on Key board
Option
•RearCam-Type : Setup for rear camera
ExtDevice - External rear camera
OEM - Original carmera
•RearCam-Power : Setup for Rear VCC wire in power cable
ON - +12V out always (current consumption : 200mA)
AUTO - +12V out in rear mode only (200mA)
OFF - Power OFF
•RearCam-Det : Setup for Rear detection
CAN - By CAN
Extwire – by rear cam detect wire
•HomeICon :Setup for a use of HOME button
ON – Activating HOME button
OFF – Disappearing HOME button
•AV out : Setup for the external AV out in OEM screen
AV1 : AV1’s AV comes out in OEM screen
AV2 : AV2’s AV comes out in OEM screen
USER : select one of AV out
Settings
GU Electronic

14
4. OSD Menu
※Press “MENU” button on Key board
Option
•Handle BUTTON : Setting for Steering wheel button (switching mode) – On or Off
•UI DVB-T(DMB) : Setting for UI DVB-T(DMB) ICON – On or Off
•UI DVD : Setting for UI DVD ICON – On or Off
•TCH_Opt : Setup for Touch Calibration (Only for Panasonic system)
※ You must select 'OSD → Utility → calibration → Execute'
in the collation before setting the touch in the option
OFF - NOT USE
0.5 – After finishing touch calibration, It is needed to select this
option so that the stored touch value can be used.
1.5 – Before doing touch calibration through navigation, It is neede
d to select this option
•NAVI COM : Output the touch data through UART
※ 1) Necessary to get Uart protocol from Navi manufacturer
2) Impossible to calibrate in Qroi
Setting: OSD → Config → NAVI-RGB → GI5000_WVGA (Select one of
Navigation Model) → Option→ QROI (Select one of Navigation
manufacturer)
•Reset : initialization
Settings
GU Electronic

15
MENU IMAGE NAVI
Config
Option
Image
Screen
Parking
Brightness
Contrast
Color- RED
Color- GREEN
Color- BLUE
50
50
50
50
25
MENU Screen NAVI
Config
Option
Image
Screen
Parking
Horizontal
Vertical
Scale X Up
Scale X Down
Scale X Up
50
50
50
50
50
MENU IMAGE Rear
Config
Option
Image
Screen
Parking
Brightness
Contrast
Saturation
Hue
Sharpness
50
50
50
50
25
- NAVI(RGB) Image / Screen
- DVD, DVBT, NAVI-AV, REAR, FRONT Image
4. OSD Menu
※Press “MENU” button on Key board
GU Electronic
Settings

16
- OSD
MENU Horizontal
OSD
IR-Ctrl
Utility
Horizontal
Vertical
Display
Transparency
Language English
50
50
10s
30
- IR – Ctrl (p.17)
- Utility
MENU Utility
OSD
IR-Ctrl
Utility
Factory Reset
Calibration
Version
Execute Cancel
Execute Cancel
TGTD01KRX - 161212
•Utilityy– INTERFACE SOFTWARE
•Calibration (Only for Panasonic system) – Setup for Touch
Calibration
Execute – You must select this item in the
collation before setting the touch in the ‘OSD – Option’
Cancel – Not use
•Version – Software source
•OSD – Horizontal
•OSD – Vertical
•OSD – Display : Setting time for displaying OSD menu
•OSD – Transparency
•OSD – Language : Setting language of ODS menu
GU Electronic
Settings
4. OSD Menu
※Press “MENU” button on Key board

※ Caution
•Delete :
ALL Clear – Delete all value
Clr – Delete one button’s Value
•Play/Pause：
To use button, Please register
the IR code in power / Pause menu
separately
17
- IR Ctrl
MENU DVB-T(DMB) DVD
OSD
IR-Ctrl
Utility
DVB- T
DVD
Sel Learn Cancel
User
Sys
MENU DVB-T(DMB) DVD
OSD
IR-Ctrl
Utility
ALL - Clear
POWER
SCAN
CH+
CH-
____ _____
____ _____
____ _____
____ _____
MENU DVB-T(DMB) DVD
OSD
IR-Ctrl
Utility
New Code :
Cfm Code :
____ _____
____ _____
Save Clr Cancel
① ②
③
① Select IR Ctrl àDVB/DVD/DVR
àLearn to register IR code
② All Clear : Remove all value of
Remote control registered before
Select one of the buttons registering
to move on to next step
③ Press a button on the remote control
of DVD/DTV then the IR code will be
appeared on “New code” menu. Press the
same button one more time to confirm
the IR code. (Cfm code = confirm code)
4. OSD Menu – Register IR code
※ Press “MENU” button on OSD Key board
GU Electronic
Settings

18
Installation
1. Installation Diagram
GND REAR POWER REAR DETECT KEY IE- IE+ BATTERY ACC
DVD IR DMB IR GND SYNC BLUE GREEN RED
COMMAND
GU Electronic

Installation
2. LVDS installation
19
[COMMAND]
GU Power
GU LVDS
GU Electronic

Installation
3. Fixing an interface board
20
Fixing the interface by the offered bolt
※ Please fix the interface by double-sided tape in RAV4 as
the hole in RAV4 does not match to the interface.
GU Electronic