Guardian SD495 User manual
USE & CARE INSTRUCTIONS
Wall Mount
Soap & Sanitizer Dispenser
Model No. SD495
1-Year Limited Warranty
English E - 1 French F - 1 Spanish S-1
Date Purchased month ________ year _________
Customer Service 1.866.603.5900
www.guardiantechnologies.com
Use GENUINE Guardian Technologies replacement parts only.
REV0321 E-1
©2016 Guardian Technologies LLC
Guardian Technologies LLC
26251 Bluestone Blvd. • Euclid, OH 44132
1.866.603.5900 • www.guardiantechnologies.com
LIMITED WARRANTY
To the consumer, Guardian Technologies LLC warrants this product to be free of defects in materials or
workmanship commencing upon the date of the original purchase. In order to be eligible for this Limited
Warranty, an original sales receipt or comparable substitute proof of purchase bearing the date of original
purchase is required. Refer to the original product carton or specific product/model page on the Guardian
Technologies website for warranty length for your particular model. This warranty applies only to the original
purchaser of this product from the original date of purchase. This warranty covers product purchased from
authorized distributors only. This warranty does not cover Guardian Technologies products that are used
outside of the US and Canada as the appliance must be plugged directly into a 120V AC electrical outlet
without the use of an adapter.
This warranty applies to repair or replacement of product found to be defective in materials or workmanship.
This warranty does not apply to damage resulting from unusual wear, commercial, abusive, unreasonable
use or supplemental damage. This warranty does not cover damage from unauthorized repairs or from any
use not in accordance with the instruction manual. Defects that are the result of normal wear and tear will
not be considered manufacturing defects under this warranty.
If this product should become defective within the warranty period, we will repair or replace any defective
parts free of charge. All warranty repairs must be completed by Guardian Technologies LLC. This warranty
gives you specific legal rights and you may also have other rights (other rights may vary from state to state
in the U.S.A.)
To submit product under warranty the complete machine must be delivered pre-paid to Guardian
Technologies LLC. Please include complete information including: the problem, the model number of the
product, the day of purchase, and a copy of the original sales receipt along with your name, address, and
telephone (email optional). Address returns to the attention of: Customer Service, at the address below.
Additional questions or comments can be made toll free to the number listed below.
USA and Canada
Guardian Technologies LLC
26251 Bluestone Blvd.
Euclid, Ohio 44132
1.866.603.5900
www.guardiantechnologies.com
Additional copies of the instruction manual can be obtained by accessing and
printing directly from our website or calling customer service.
Please go to www.guardiantechnologies.com to register your product. We consider the registration process
important to ensuring superior service to our customers, however submitting the registration is optional
and does not affect your rights to utilize this warranty according to the conditions stated above.
Automatic Dispenser
Place Hands Below
E-2 E-3
PRODUCT SPECIFICATIONS AND PARTS
READ AND SAVE THESE INSTRUCTIONS
WARNINGS
Failure to comply with the warnings listed below may
result in electric shock or serious injury.
This product should be used only in accordance with the specifications
outlined in this manual. Usage other than what has been specified here
may result in serious injury.
When using electrical appliances, basic precautions should always be followed to
reduce the risk of fire, electric shock and injury to persons, including the following:
• Always use the designated spout for liquid, foam or gel soaps/sanitizers.
• Use caution when using hand sanitizers that contain flammable ingredients.
Read and follow soap/sanitizer manufacturer instructions before use.
• For normal “automatic dispensing,” do not mix water with liquid soap, sanitizer or lotion.
• Do not rinse, submerge, or allow liquid to enter the battery compartment.
• Do not immerse the unit in water to avoid the malfunction of the inner
electrical parts of the unit.
• Do not expose the unit directly to strong sunlight otherwise it will cause the malfunction
of the infrared sensor.
• Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
• If appliance is not working as it should, has been dropped, damaged, left outdoors or
dropped in water, call Customer Service.
• Remove batteries before any routine cleaning or maintenance.
• Leaks from battery cells can occur under extreme conditions. If the liquid gets on the
skin (1) wash quickly with soap and water or (2) neutralize with a mild acid such as
lemon juice or vinegar. If the liquid gets into the eyes, flush them immediately with
clean water for a minimum of 10 minutes. Seek medical attention.
• Use only 4 AA batteries (4).
WARNING: Cancer or Reproductive Harm.
For more information go to www.P65Warnings.ca.gov.
Window
Automatic Dispenser
Place Hands Below
Indicator Light
Infrared Sensor
Refill Bottle
Indicator Light
Pump
Battery Compartment
Pumping Cycle Button
Cover
Key Entry
Front Cover Switch
Key Screw and Anchors (3 each)
Foam
Dispenser
Gel
Dispenser
Liquid
Dispenser
E-2 E-3
PRODUCT SPECIFICATIONS AND PARTS
READ AND SAVE THESE INSTRUCTIONS
WARNINGS
Failure to comply with the warnings listed below may
result in electric shock or serious injury.
This product should be used only in accordance with the specifications
outlined in this manual. Usage other than what has been specified here
may result in serious injury.
When using electrical appliances, basic precautions should always be followed to
reduce the risk of fire, electric shock and injury to persons, including the following:
• Always use the designated spout for liquid, foam or gel soaps/sanitizers.
• Use caution when using hand sanitizers that contain flammable ingredients.
Read and follow soap/sanitizer manufacturer instructions before use.
• For normal “automatic dispensing,” do not mix water with liquid soap, sanitizer or lotion.
• Do not rinse, submerge, or allow liquid to enter the battery compartment.
• Do not immerse the unit in water to avoid the malfunction of the inner
electrical parts of the unit.
• Do not expose the unit directly to strong sunlight otherwise it will cause the malfunction
of the infrared sensor.
• Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
• If appliance is not working as it should, has been dropped, damaged, left outdoors or
dropped in water, call Customer Service.
• Remove batteries before any routine cleaning or maintenance.
• Leaks from battery cells can occur under extreme conditions. If the liquid gets on the
skin (1) wash quickly with soap and water or (2) neutralize with a mild acid such as
lemon juice or vinegar. If the liquid gets into the eyes, flush them immediately with
clean water for a minimum of 10 minutes. Seek medical attention.
• Use only 4 AA batteries (4).
WARNING: Cancer or Reproductive Harm.
For more information go to www.P65Warnings.ca.gov.
Window
Automatic Dispenser
Place Hands Below
Indicator Light
Infrared Sensor
Refill Bottle
Indicator Light
Pump
Battery Compartment
Pumping Cycle Button
Cover
Key Entry
Front Cover Switch
Key Screw and Anchors (3 each)
Foam
Dispenser
Gel
Dispenser
Liquid
Dispenser
Dispenser Installation
The automatic soap dispenser must be installed at least 8” away from other furniture.
1. Insert the anti-theft key in the keyhole at the top of the dispenser, grip the top of the
back of the dispenser while holding the top of the cover by hand, and open it gently
downward. The cover will be on the bottom of the dispenser (see figure 1).
2. Remove the liner refill bottle and pump head by sliding it out. Remove the battery
compartment by pressing the two tabs above the compartment and slide the whole
assembly upward to release (see figure 2).
3. There are 2 options for installing wall anchors (see figure 3). After choosing wall anchor
installation, place the dispenser on the wall where you want to install dispenser.
4. Mark the wall anchor locations and drill a hole for each wall anchor (4-6 mm). Insert the
anchor into the wall. Align the dispenser (check to make sure it is facing the right
direction and open cover is at the bottom of the dispenser) and secure with screws
(see figure 4).
5. Replace the liner refill bottle, pump head and battery compartment.
Adding Soap or Sanitizer
1. Remove the soap dispenser refill bottle and pump from the dispenser.
2. Select the proper pump for the type of soap or sanitizer being added.
See chart below:
E-4 E-5
3. First install selected pump by sliding it into refill bottle
opening at the bottom of the bottle. It will be a snug fit
(see figure 6).
4. After the correct pump is installed, open the cap of the
refill bottle and pour in the soap or sanitizer. The bottle
will hold up to 1000ml. Return and secure cap.
5. Use the window to see when it’s time to refill the liquid
in the bottle.
Note: Clean the nozzle periodically to remove soap or
sanitizer build up, especially if a gel solution is used. This
will prevent the nozzle head from blocked and not working.
Note: if switching the type of soap/sanitizer, be sure the refill bottle is completely empty.
Foam
Dispenser
(Yellow)
Gel
Dispenser
(Green)
Liquid
Dispenser
(Blue)
1
2
3
5
6
Battery Installation
Open the soap dispenser. The battery holder is on the
right side facing the soap dispenser. Note the arrow on
the cover and slide the cover forward to remove.
Insert four (4) AA batteries as shown (see figure 5).
Return the battery cover by sliding it back
over the side of the compartment.
Dispenser Installation
The automatic soap dispenser must be installed at least 8” away from other furniture.
1. Insert the anti-theft key in the keyhole at the top of the dispenser, grip the top of the
back of the dispenser while holding the top of the cover by hand, and open it gently
downward. The cover will be on the bottom of the dispenser (see figure 1).
2. Remove the liner refill bottle and pump head by sliding it out. Remove the battery
compartment by pressing the two tabs above the compartment and slide the whole
assembly upward to release (see figure 2).
3. There are 2 options for installing wall anchors (see figure 3). After choosing wall anchor
installation, place the dispenser on the wall where you want to install dispenser.
4. Mark the wall anchor locations and drill a hole for each wall anchor (4-6 mm). Insert the
anchor into the wall. Align the dispenser (check to make sure it is facing the right
direction and open cover is at the bottom of the dispenser) and secure with screws
(see figure 4).
5. Replace the liner refill bottle, pump head and battery compartment.
Adding Soap or Sanitizer
1. Remove the soap dispenser refill bottle and pump from the dispenser.
2. Select the proper pump for the type of soap or sanitizer being added.
See chart below:
E-4 E-5
3. First install selected pump by sliding it into refill bottle
opening at the bottom of the bottle. It will be a snug fit
(see figure 6).
4. After the correct pump is installed, open the cap of the
refill bottle and pour in the soap or sanitizer. The bottle
will hold up to 1000ml. Return and secure cap.
5. Use the window to see when it’s time to refill the liquid
in the bottle.
Note: Clean the nozzle periodically to remove soap or
sanitizer build up, especially if a gel solution is used. This
will prevent the nozzle head from blocked and not working.
Note: if switching the type of soap/sanitizer, be sure the refill bottle is completely empty.
Foam
Dispenser
(Yellow)
Gel
Dispenser
(Green)
Liquid
Dispenser
(Blue)
1
2
3
5
6
Battery Installation
Open the soap dispenser. The battery holder is on the
right side facing the soap dispenser. Note the arrow on
the cover and slide the cover forward to remove.
Insert four (4) AA batteries as shown (see figure 5).
Return the battery cover by sliding it back
over the side of the compartment.
TROUBLE SHOOTING GUIDE
Unit won’t power on. Make sure batteries are inserted properly.
Replace with new batteries.
PROBLEM SOLUTION
Too much/too little soap
is being dispensed. Adjust the liquid volume (see filling instructions).
Make sure batteries are working properly.
Confirm dispenser is connected and in the liquid.
Refill soap.
Remove any soap build up from pump.
Make sure batteries are working properly.
Batteries are low.
The unit sensor is still activated by a hand or object, even
though the cycle is complete. Remove hand/object.
E-6 E-7
Installation of the Refill Bottle and Pump
1. Return the refill bottle to the dispenser. The refill bottle
markings should face outward to be lined up correctly.
2. Gently slide the refill bottle and pump head into the
dispenser, it will sit on top of the battery compartment.
The pump will fit within the battery compartment grooves.
Make sure the push rod engages in the empty position
1 on top of the discharge nozzle of the pump
(see figure 7).
3. You can select a single or double dispensing cycle.
To select single or double dispensing cycle you press
the black pumping cycle button (see figure 7).
Tip: A double dispensing may be preferred with a
thick gel or foam soap.
Light will flash 3 times for single cycle dispensing.
Light will flash twice rapidly 3 times for double cycle
dispensing.
4. Close and lock dispenser cover.
Black
Pumping
Cycle
Button
Push Rod
7
Product Usage
1. The indicator light on the front of the dispenser
will be green when it’s ready to use.
2. Place hands under the dispenser to activate
the infrared sensor.
3. The light turns red when the batteries are low
or the sensor is still activated by a hand or object,
even though the cycle is complete.
Automatic Dispenser
Place Hands Below
Indicator Light
No liquid is being
dispensed.
Unit turns off.
Indicator light is Red.
TROUBLE SHOOTING GUIDE
Unit won’t power on. Make sure batteries are inserted properly.
Replace with new batteries.
PROBLEM SOLUTION
Too much/too little soap
is being dispensed. Adjust the liquid volume (see filling instructions).
Make sure batteries are working properly.
Confirm dispenser is connected and in the liquid.
Refill soap.
Remove any soap build up from pump.
Make sure batteries are working properly.
Batteries are low.
The unit sensor is still activated by a hand or object, even
though the cycle is complete. Remove hand/object.
E-6 E-7
Installation of the Refill Bottle and Pump
1. Return the refill bottle to the dispenser. The refill bottle
markings should face outward to be lined up correctly.
2. Gently slide the refill bottle and pump head into the
dispenser, it will sit on top of the battery compartment.
The pump will fit within the battery compartment grooves.
Make sure the push rod engages in the empty position
1 on top of the discharge nozzle of the pump
(see figure 7).
3. You can select a single or double dispensing cycle.
To select single or double dispensing cycle you press
the black pumping cycle button (see figure 7).
Tip: A double dispensing may be preferred with a
thick gel or foam soap.
Light will flash 3 times for single cycle dispensing.
Light will flash twice rapidly 3 times for double cycle
dispensing.
4. Close and lock dispenser cover.
Black
Pumping
Cycle
Button
Push Rod
7
Product Usage
1. The indicator light on the front of the dispenser
will be green when it’s ready to use.
2. Place hands under the dispenser to activate
the infrared sensor.
3. The light turns red when the batteries are low
or the sensor is still activated by a hand or object,
even though the cycle is complete.
Automatic Dispenser
Place Hands Below
Indicator Light
No liquid is being
dispensed.
Unit turns off.
Indicator light is Red.
USE & CARE INSTRUCTIONS
Wall Mount
Soap & Sanitizer Dispenser
Model No. SD495
1-Year Limited Warranty
English E - 1 French F - 1 Spanish S-1
Date Purchased month ________ year _________
Customer Service 1.866.603.5900
www.guardiantechnologies.com
Use GENUINE Guardian Technologies replacement parts only.
REV0321 E-1
©2016 Guardian Technologies LLC
Guardian Technologies LLC
26251 Bluestone Blvd. • Euclid, OH 44132
1.866.603.5900 • www.guardiantechnologies.com
LIMITED WARRANTY
To the consumer, Guardian Technologies LLC warrants this product to be free of defects in materials or
workmanship commencing upon the date of the original purchase. In order to be eligible for this Limited
Warranty, an original sales receipt or comparable substitute proof of purchase bearing the date of original
purchase is required. Refer to the original product carton or specific product/model page on the Guardian
Technologies website for warranty length for your particular model. This warranty applies only to the original
purchaser of this product from the original date of purchase. This warranty covers product purchased from
authorized distributors only. This warranty does not cover Guardian Technologies products that are used
outside of the US and Canada as the appliance must be plugged directly into a 120V AC electrical outlet
without the use of an adapter.
This warranty applies to repair or replacement of product found to be defective in materials or workmanship.
This warranty does not apply to damage resulting from unusual wear, commercial, abusive, unreasonable
use or supplemental damage. This warranty does not cover damage from unauthorized repairs or from any
use not in accordance with the instruction manual. Defects that are the result of normal wear and tear will
not be considered manufacturing defects under this warranty.
If this product should become defective within the warranty period, we will repair or replace any defective
parts free of charge. All warranty repairs must be completed by Guardian Technologies LLC. This warranty
gives you specific legal rights and you may also have other rights (other rights may vary from state to state
in the U.S.A.)
To submit product under warranty the complete machine must be delivered pre-paid to Guardian
Technologies LLC. Please include complete information including: the problem, the model number of the
product, the day of purchase, and a copy of the original sales receipt along with your name, address, and
telephone (email optional). Address returns to the attention of: Customer Service, at the address below.
Additional questions or comments can be made toll free to the number listed below.
USA and Canada
Guardian Technologies LLC
26251 Bluestone Blvd.
Euclid, Ohio 44132
1.866.603.5900
www.guardiantechnologies.com
Additional copies of the instruction manual can be obtained by accessing and
printing directly from our website or calling customer service.
Please go to www.guardiantechnologies.com to register your product. We consider the registration process
important to ensuring superior service to our customers, however submitting the registration is optional
and does not affect your rights to utilize this warranty according to the conditions stated above.
Automatic Dispenser
Place Hands Below
Other manuals for SD495
1
Table of contents
Other Guardian Dispenser manuals
