GYMBOSS miniMAX User manual

www.gymboss.com
Thank you for purchasing a GYMBOSS miniMAX.
***Remove protective screen from front of timer.
TURN ON | Push any button.
TURN OFF | Interval timer will turn off after no use for 5 minutes, or you may select off
from the menu.
If left in stopwatch and clock mode timer will not turn off on its own.
BUTTON CONFIGURATION
Battery:
No Used Batteries Please! We recommend a high quality Energizer or Duracell.
When your battery gets low a battery icon will flash on the screen.
REBOOT a frozen or malfunctioning timer by placing a NEW battery in timer, then using a
pen, push the REBOOT button. (See in-depth Troubleshooting and Replacement
Procedure document also available here on our website)
There are 3 modes to the GYMBOSS miniMAX.
CLOCK
STOPWATCH
INTERVAL TIMER –the interval timer has 4 separate sections, depending on how
many intervals you wish to time.
1. 1 Interval
2. 2 Intervals
3. 3+ intervals (3 to 25 different intervals in sequence).
4. Multi (2 to 25 different intervals and allows repeating of each interval or
groups of intervals within the 25 intervals. See setup below).
There are 2 menus, the menu allows you to select desired mode, the Setup Menu
allows you to create, save, or recall programs as well as return to the Menu to select
a different mode

MENU
SETUP MENU
OFF
(Turn off)
MENU
1 INT
(Time 1 interval)
>SETUP
>2 INT
(Time 2 different intervals)
RECALL
3+ INT
(3-25 different intervals)
SAVE
MULTI
(Up to 25 with repeats and group repeats)
BACK
STPWCH
(Stopwatch)
CLOCK
Only 3 lines of each menu will be on the screen at any one time and they are located on
the top left part of the LCD screen. The > located at the center line indicates what will
be activated when you push the SET button. The remaining will be off-screen and you
will use the Vor Λbuttons to scroll the menu to access them.
Each mode has a distinctive look. Here they are shown for comparison purposes.
1 INT
2 INT
3+INT
MULTI
STOPWATCH
CLOCK
To change modes:
From the MENU use the V / Λbuttons to move the desired mode to the > position,
then push the SET button.
1 INT, 2 INT, and 3+ INT TIMER SETUP
Choose MENU, then choose your desired mode (1 INT, 2 INT, or 3+ INT)
Push SET button, >SETUP menu will appear, push SET again to select
SETUP. SET is now displayed on the screen allowing changes to the displayed
program.

If SET is not displayed on screen, you are not in setup and cannot make
changes.
Set the interval times using the V / Λbuttons. Push SET to move to next
interval setup. For 3+ interval mode, after you have set all of your desired
intervals select 00:00 for the next interval and push SET to move to the next
step of the setup process.
Select # of rounds (repeats) desired from 00-99. Rounds set from 01-99, timer
will complete the selected number of rounds. Rounds set to 00, timer will count
the rounds completed up to 99.
Set alarm type B(big beep), b(little beep), V(vibrate), or any combination.
Set alarm duration of 1, 2, 5, or 9seconds. Push SET to exit setup, SET will
disappear from screen.
Interval Timer Setup Tips:
In SETUP push START button to backup to previous step.
Hold V or Λto fast scroll.
While fast scrolling, each push of SET will increase/decrease 10 minutes.
Push V and Λat the same time will set default value.
Interval Timer Operating Tips:
Stop timing –hold START button (about 3 seconds), alarm occurs.
Pause timing –push START 3 times in rapid succession, alarm occurs on
successful pause.
During PAUSE you may change the alarm by pushing the SET button.
During PAUSE push START to resume timing, alarm occurs.
SAVE
To save the current program push SET, then scroll Vto >SAVE, then
scroll to save to desired location, then push SET.
If there is a program saved
at this P#, it will be
displayed. Push SET to
save your program and
delete this one.
RECALL
To recall a saved program, you must be in the mode according to # of
intervals, if you are recalling a program with 2 different intervals, you
must be in the 2 INT mode. Select desired interval mode, 1 INT, 2 INT,
3+ INT, or MULTI. Push SET, then scroll to >RECALL, then scroll to the
desired program, then push SET.
VIEW
For 3+ INT and MULTI modes you may view the intervals in the
displayed program by using the v button. If you want to change an
interval during this process push SET button, this will put the timer in
setup and allow you to make the desired changes.

EXPANDED MULTI INTERVAL SETUP
MULTI mode allows up to 25 intervals and repeat single intervals, or groups of
intervals, within the 25.
05:00 x 1
One 5 minute interval.
00:20 x 8
00:10 x P
Using a P causes the timer to alternate this interval with the previous
interval, in this case –20 sec / 10 sec, 8 times. During setup of the # of
interval repeats, P is down (V) from 00.
02:00 x 3
Three 2 minute intervals.
05:00 x 1
One 5 minute interval.
MULTI interval display during timing
EXPANDED STOPWATCH OPERATION
To use the stopwatch mode: Push SET, choose MENU, push SET again,
choose STPWCH, push SET.
Push START button to start, stop, or resume timing. (alarm occurs with each
push).
Push Vto reset back to 00:00
To change alarm type, Push SET, choose SETUP, push SET again, then use
the V / Λbuttons to change alarm type to BH, BL, V, BHV, or BLV. Push SET.
EXPANDED CLOCK SETUP and TIPS:
To use the Clock mode: Push SET, choose MENU, push SET again, choose
CLOCK, push SET.
To change the time: While in Clock mode, Push SET, choose SETUP, push
SET. Use the V / Λbuttons to change the time, pushing SET after each.
The clock can be viewed from any other mode even during timing by holding ^
button for 1 second. This is not available while in setup mode.

HOW TO REMOVE THE BELT-CLIP
1. Turn the timer so that you are looking at the back.
2. Insert your fingernail on latch between belt clip and START button and pull the
latch towards the belt clip while at the same time pushing the belt clip to the
right to release. It will then slide off.
3. If you are still having trouble, please see instructional video on YouTube.
***Lanyard may be attached to timer body next to the START button.