H3C MSR 5600 User manual

i
Contents
Preparing for installation················································································1
Safety recommendations ···································································································································1
Safety symbols···········································································································································1
General safety recommendations··············································································································1
Electricity safety·········································································································································1
Laser safety················································································································································2
Examining the installation site····························································································································2
Temperature and humidity·························································································································2
Cleanliness·················································································································································2
Cooling system···········································································································································3
ESD prevention··········································································································································3
EMI·····························································································································································4
Lightning protection····································································································································4
Rack-mounting···········································································································································5
Installation tools and accessories ······················································································································5
Pre-installation checklist·····································································································································6

1
Preparing for installation
The MSR5600 router series includes the models in Table 1.
Table 1 MSR5600 router series models
Model (on the front panel)
Product code
MSR5620 RT-MSR5620
MSR 56-60 RT-MSR5660
MSR 56-80 RT-MSR5680
Safety recommendations
Safety symbols
When reading this document, note the following symbols:
WARNING means an alert that calls attention to important information that if not understood or
followed can result in personal injury.
CAUTION means an alert that calls attention to important information that if not understood or
followed can result in data loss, data corruption, or damage to hardware or software.
General safety recommendations
•
Keep the chassis and installation tools away from walk areas.
•
Make sure the ground is dry and flat and anti-slip measures are in place.
•
Unplug all the external cables (including power cords) before moving the chassis.
Electricity safety
•
Locate the emergency power-off switch in the room before installation. Shut the power off at
once in case accident occurs. Disconnect the power cord of the router if necessary.
•
Make sure the router is correctly grounded.
•
Do not open or close the chassis cover when the router is powered on.
•
Correctly connect the interface cables of the router.
•
Use an uninterrupted power supply (UPS).
•
If there are two power inputs, disconnect the two power inputs to power off the router.
•
Do not work alone when the router has power.
•
Always make sure the power has been disconnected during the installation and replacement
procedures.

2
Laser safety
WARNING!
Do not stare into any
open apertures of operating transceiver modules or optical fiber connectors.
The laser light emitted from these apertures might hurt your eyes.
CAUTION:
•
Before you remove the optical fiber connector from a fiber port, execute the shutdown
command
in interface view to shut down the port.
•
Insert a dust cap into any unused optical fiber connector and a dust plug into any unused fiber
port or transceiver module port to protect them from contamination and ESD damage.
Examining the installation site
The routers can only be used indoors. To make sure the router operates correctly and to prolong its
service lifetime, the installation site must meet the following requirements.
Temperature and humidity
Maintain temperature and humidity in the equipment room as described in Table 2.
•
Lasting high relative humidity can cause poor insulation, electricity leakage, mechanical
property change of materials, and metal corrosion.
•
Lasting low relative humidity can cause washer contraction and ESD and bring problems
including loose captive screws and circuit failure.
•
High temperature can accelerate the aging of insulation materials and significantly lower the
reliability and lifespan of the router.
Table 2 Temperature and humidity requirements
Operating temperature
Operating humidity
0°C to 45°C (32°F to 113°F) 5% RH to 95% RH, noncondensing
Cleanliness
Dust buildup on the chassis might result in electrostatic adsorption, which causes poor contact of
metal components and contact points, especially when indoor relative humidity is low. In the worst
case, electrostatic adsorption can cause communication failure. To ensure correct operation, the
equipment room must meet the dust concentration requirements listed in Table 3.
Table 3 Dust concentration limit in the equipment room
Substance
Concentration limit (particles/m
3
)
Dust particles ≤ 3 x 104
(No visible dust on desk in three days)
NOTE:
Dust particle diameter ≥ 5 µm
The equipment room must also meet strict limits on salts, acids, and sulfides to eliminate corrosion
and premature aging of components, as shown in Table 4.

3
Table 4 Harmful gas limits in the equipment room
Gas
Max. (mg/m
3
)
SO20.2
H2S 0.006
NH30.05
Cl20.01
NO20.04
Cooling system
The router uses left to rear airflow for heat dissipation.
Figure 1 Airflow through the MSR 5600 chassis
To ensure good ventilation, the following requirements must be met:
•
Leave a minimum clearance of 10 cm (3.94 in) for the air inlet and outlet vents.
•
The installation site has a good cooling system.
ESD prevention
CAUTION:
Check the resistance of the
ESD wrist strap for safety. The resistance reading should be in the range
of 1 to 10 megohm (Mohm) between human body and the ground.
To prevent electrostatic discharge (ESD), follow these guidelines:
•
Make sure the router and the floor are reliably grounded.
•
Take dust-proof measures for the equipment room.
•
Maintain the humidity and temperature at acceptable levels.

4
•
Always wear an ESD wrist strap and ESD cloth when touching a circuit board or transceiver
module.
The router does not supply an ESD wrist wrap. Prepare an ESD wrist wrap yourself.
•
Place the removed memory module, CF card, or interface module on an antistatic workbench,
with the face upward, or put it into an antistatic bag.
•
Touch only the edges, instead of electronic components when you observe or move a removed
memory module, CF card, or interface module.
To attach an ESD wrist strap:
1. Wear the wrist strap on your wrist.
2. Lock the wrist strap tight around your wrist to keep good contact with the skin.
3. Insert the ESD plug into the ESD socket.
4. Connect the alligator clip to the rack.
EMI
All electromagnetic interference (EMI) sources, from outside or inside of the router and application
system, adversely affect the router in the following ways:
•
A conduction pattern of capacitance coupling.
•
Inductance coupling.
•
Electromagnetic wave radiation.
•
Common impedance (including the grounding system) coupling.
To prevent EMI, perform the following tasks:
•
If AC power is used, use a single-phase three-wire power receptacle with protection earth (PE)
to filter interference from the power grid.
•
Keep the router far away from radio transmitting stations, radar stations, and high-frequency
devices to make sure the EMI levels do not exceed the compliant range.
•
Use electromagnetic shielding, for example, shielded interface cables, when necessary.
•
To prevent signal ports from getting damaged by overvoltage or overcurrent caused by lightning
strikes, only route interface cables indoors. If you must route interface cables outdoors, install
network port lightning protectors.
Lightning protection
The router has its own lightning protection system. To better protect the router from lightning, do as
follows:
•
Make sure the grounding cable of the chassis is reliably grounded.
•
Make sure the grounding terminal of the AC power receptacle is reliably grounded.
•
Install a lightning arrester at the input end of the power supply to enhance the lightning
protection capability of the power supply.
•
Install a special lightning arrester at the input end of outdoor signal lines (for example, E1/T1
line) to which interface modules of the router are connected to enhance the lightning protection
capability.

5
Rack-mounting
Before mounting the router in a standard 19-inch rack, adhere to the following requirements:
•
The rack is equipped with a good ventilation system.
•
The rack is sturdy enough to support the router and its accessories.
•
For heat dissipation and device maintenance, make sure the front and rear of the rack are at
least 0.8 m (2.62 ft) away from walls or other devices, and the headroom in the equipment room
is no less than 3 m (9.84 ft).
Installation tools and accessories
Figure 2 Installation tools
Figure 3 Installation accessories
Multimeter
Flathead screwdriver Phillips screwdriver Needle-nose pliers Wire-stripping pliers
ESD wrist strap Diagonal pliers Heat gun Cable tester Marker
Cage nut
(user-supplied)
Grounding cable
Removable cable tie
(user-supplied)
M6 rack screw
(user-supplied)
Air filter (optional)
M3 countersunk-head
screw (optional)
M4 mounting bracket
screw
MSR5620 shoulder
screw
MSR5620 front
mounting brackets MSR 56-60 front mounting brackets MSR 56-80 front mounting brackets MSR5620 rear mounting brackets

6
Pre-installation checklist
Table 5 Pre-installation checklist
Item
Requirements
Result
Installation
site
Ventilation
•There is a minimum clearance of 10 cm (3.94 in)
around the inlet and outlet vents for heat dissipation of
the router chassis.
•A good ventilation system is available at the installation
site.
Operating
temperature 0°C to 45°C (32°F to 113°F).
Operating
humidity 5% RH to 95% RH, noncondensing.
Cleanliness •Dust concentration ≤ 3 × 104particles/m3.
•No visible dust on desk within three days.
ESD prevention
•The equipment and floor are reliably grounded.
•The equipment room is dust-proof.
•The humidity and temperature are at acceptable levels.
•An ESD wrist strap is available.
EMI prevention
•Effective measures are taken for filtering interference
from the power grid.
•The protection ground of the router is away from the
grounding facility of power equipment or lightning
protection grounding facility.
•The router is far away from radio transmitting stations,
radar stations, and high-frequency devices.
•Electromagnetic shielding, for example, shielded
interface cables, is used as required.
Lightning
protection
•The device is reliably grounded.
•The AC power source is reliably grounded.
•(Optional.) Network port lightning protectors are
available.
•(Optional.) Asurge protected power strip is available.
Electricity safety
•A UPS is available.
•The power-off switch in the equipment room is
identified and accessible so that the power can be
immediately shut off when an accident occurs.
Workbench •The workbench is stable enough.
•The workbench is reliably grounded.
Rack-mounting
requirements
•The rack has a good ventilation system.
•The rack is sturdy enough to support the weight of the
router and installation accessories.
•The size of the rack is appropriate for the router.
•The front and rear of the rack are a minimum of 0.8 m
(2.62 ft) away from walls or other devices.
Safety
precautions
•The router is far away from any moist area and heat source.
•The emergency power switch in the equipment room is located.
Tools •Installation accessories supplied with the router are available.
•User supplied tools are available.

7
Item
Requirements
Result
Reference •Documents shipped with the router are available.
•Online documents are available.