H3C S10500X Series User manual

H3C S10500X Switch Series
OAA Configuration Guide
New H3C Technologies Co., Ltd.
http://www.h3c.com
Software version: Release 7585P05 and later versions
Document version: 6W100-20200529

Copyright © 2020, New H3C Technologies Co., Ltd. and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior written
consent of New H3C Technologies Co., Ltd.
Trademarks
Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this
document are the property of their respective owners.
Notice
The information in this document is subject to change without notice. All contents in this document, including
statements, information, and recommendations, are believed to be accurate, but they are presented without
warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions
contained herein.

Preface
This configuration guide describes OAA fundamentals and configuration. It describes how to
configure the H3C open application platform (OAP) module connected to your device to exchange
information between your device and the OAP module.
This preface includes the following topics about the documentation:
•
Audience.
•
Conventions.
•
Documentation feedback.
Audience
This documentation is intended for:
•
Network planners.
•
Field technical support and servicing engineers.
•
Network administrators working with the S7500E switch series.
Conventions
The following information describes the conventions used in the documentation.
Command conventions
Convention
Description
Boldface Bold text represents commands and keywords that you enter literally as shown.
Italic Italic text represents arguments that you replace with actual values.
[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.
{ x | y | ... }
Braces enclose a set of required syntax choices separated by vertical bars, from which
you select one.
[ x | y | ... ]
Square brackets enclose a set of optional syntax choices separated by vertical bars,
from which you select one or none.
{ x | y | ... } *
Asterisk marked braces enclose a set of required syntax choices separated by vertical
bars, from which you select a minimum of one.
[ x | y | ... ] *
Asterisk marked square brackets enclose optional syntaxchoices separated by vertical
bars, from which you select one choice, multiple choices, or none.
&<1-n> The argument or keyword and argument combination before the ampersand (&) sign
can be entered 1 to n times.
# A line that starts with a pound (#) sign is comments.
GUI conventions
Convention
Description
Boldface Window names, button names, field names, and menu items are in Boldface. For
example, the New User window opens; click OK.
>
Multi-level menus are separated by angle brackets. For example, File > Create >

Convention
Description
Folder.
Symbols
Convention
Description
WARNING! An alert that calls attention to important information that if not understood or followed
can result in personal injury.
CAUTION:
An alert that calls attention to important information that if not understood or followed
can result in data loss, data corruption, or damage to hardware or software.
IMPORTANT:
An alert that calls attention to essential information.
NOTE:
An alert that contains additional or supplementary information.
TIP:
An alert that provides helpful information.
Network topology icons
Convention
Description
Represents a generic network device, such as a router, switch, or firewall.
Represents a routing-capable device, such as a router or Layer 3 switch.
Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that
supports Layer 2 forwarding and other Layer 2 features.
Represents an access controller, a unified wired-WLAN module, or the access
controller engine on a unified wired-WLAN switch.
Represents an access point.
Represents a wireless terminator unit.
Represents a wireless terminator.
Represents a mesh access point.
Represents omnidirectional signals.
Represents directional signals.
Represents a security product, such as a firewall, UTM, multiservice security
gateway, or load balancing device.
Represents a security module, such as a firewall, load balancing, NetStream, SSL
VPN, IPS, or ACG module.
T
T
T
T

Examples provided in this document
Examples in this document might use devices that differ from your device in hardware model,
configuration, or software version. It is normal that the port numbers, sample output, screenshots,
and other information in the examples differ from what you have on your device.
Documentation feedback
You can e-mail your comments about product documentation to inf[email protected].
We appreciate your comments.

1
Contents
Configuring OAP····························································································1
Overview····························································································································································1
OAP functions············································································································································1
OAP manager timers··································································································································2
Configuring OAP················································································································································2
Enabling OAP·············································································································································2
Setting the clock synchronization timer······································································································2
Setting the client monitoring timer··············································································································2
Managing OAP clients········································································································································3
Restarting an OAP client····························································································································3
Shutting down an OAP client ·····················································································································3
Displaying and maintaining OAP························································································································3

1
Configuring OAP
Overview
The Open Application Platform (OAP) is an open application protocol that is based on the Open
Application Architecture (OAA). OAA allows products from different vendors to operate together to
meet service requirements.
Figure 1 OAA diagram
As shown in Figure 1, OAA includes the following components:
•
Routing/switching component—Provides routing and switching services. This component is
the control center of the entire architecture.
•
Standalone service component—Provides services to meet specific requirements.
•
Interfacing component—Connects the standalone service component to the
routing/switching component.
OAP is used for communication and cooperation between the routing/switching component and the
standalone service component. The routing/switching component is the OAP manager, and the
standalone service component is the OAP client.
The device can act as the OAP manager. The OAP manager software is integrated in the Comware
system.
The OAP client can be a third-party product or an OAP module. OAP modules provide value-added
services, such as security and wireless control. OAP modules have their own CPUs and storage
media. The OAP client software is integrated in the operating system of the OAP module as a
function.
You can install an OAP module in the device. For example, you can install an IDS/IPS OAP module
in the device to provide intrusion detection and protection services.
OAP functions
OAP provides the following functions:
•
OAP clients register with and deregister from the OAP manager.
•
The OAP manager assigns IDs to OAP clients to uniquely identify the clients.
•
The OAP manager and an OAP client exchange information to, for example, monitor each other
and synchronize the clock.
From the OAP manager, you can perform the following tasks:
•
Restart OAP clients.
•
Shut down OAP clients.
•
Display OAP client information.
An OAP manager can manage up to 255 OAP clients.
Standalone service
component Routing/switching component
Interfacing
component

2
OAP manager timers
The OAP manager uses the following timers:
•
Clock synchronization timer—Regularly triggers the OAP manager to send clock and time
zone synchronization notifications to OAP clients. This mechanism keeps the clients' clocks
synchronized with the manager's clock.
•
Client monitoring timer—Regularly triggers the OAP manager to send client monitoring
packets to OAP clients.
Configuring OAP
IMPORTANT:
This feature is available on
the following modules:
•
LSUM1WCMX20RT
•LSUM1WCMX40RT
Enabling OAP
Step
Command
Remarks
1. Enter system view. system-view N/A
2. Enter interface view. interface interface-type
interface-number
N/A
3. Enable OAP. oap enable By default, OAP is disabled on an
interface.
Setting the clock synchronization timer
Step
Command
Remarks
1. Enter system view.system-view N/A
2. Set the clock synchronization
timer. oap timer clock-sync minutes By default, the clock
synchronization timer is set to 5
minutes.
Setting the client monitoring timer
Step
Command
Remarks
1. Enter system view.system-view N/A
2. Set the client monitoring timer. oap timer monitor seconds By default, the client monitoring
timer is set to 5 seconds.

3
Managing OAP clients
IMPORTANT:
This feature is available on
the following modules:
•
LSUM1WCMX20RT
•LSUM1WCMX40RT
You can restart or shut down an OAP client.
Restarting an OAP client
Step
Command
1. Enter system view.system-view
2. Restart an OAP client. oap client reboot client-id
Shutting down an OAP client
This feature applies only to OAP clients on Linux.
To shut down an OAP client:
Step
Command
1. Enter system view.system-view
2. Shut down an OAP client. oap client close client-id
Displaying and maintaining OAP
IMPORTANT:
This feature is available on
the following modules:
•
LSUM1WCMX20RT
•LSUM1WCMX40RT
Execute display commands in any view.
Task
Command
Display the summary registration information
of OAP clients. display oap client summary [ client-id ]
Display OAP client information. display oap client info [ client-id ]

i
Contents
Configuring the OAP module·········································································1
Internal interfaces for OAP modules··················································································································1
Logging in to an OAP module····························································································································2
Logging in through the console port on the OAP module ··········································································2
Logging in through the management Ethernet port on the OAP module by using SSH ····························2
Logging in through the internal Ethernet interface on the OAP module by using SSH······························2
Logging in to the OAP module from the CLI of the device·········································································3
Resetting OAP modules·····································································································································3