H3C S6520-SI Series Installation manual

H3C S6520X-SI & S6520-SI &
S5000-EI & MS4600 Switch Series
Virtual Technologies Command Reference
"H3C S6520X-SI Switch Series"
"H3C S6520-SI Switch Series"
"H3C S5000-EI Switch Series"
"H3C MS4600 Switch Series"
New H3C Technologies Co., Ltd.
http://www.h3c.com
Software version: Release 1110
Document version: 6W100-20180821

Copyright © 2018, New H3C Technologies Co., Ltd. and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior written
consent of New H3C Technologies Co., Ltd.
Trademarks
H3C, , H3CS, H3CIE, H3CNE,Aolynk, , H3Care, , IRF, NetPilot, Netflow, SecEngine,
SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New H3C Technologies
Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their respective owners.
Notice
The information in this document is subject to change without notice. All contents in this document, including
statements, information, and recommendations, are believed to be accurate, but they are presented without
warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions
contained herein.

Preface
This command reference describes IRF configuration commands for setting up and maintaining an
IRF fabric, including:
•Commands for IRF port binding configuration.
•Commands for IRF member ID and priority configuration.
•Commands for detecting IRF splits and maintaining the IRF fabric.
This preface includes the following topics about the documentation:
•Audience.
•Conventions.
•Documentation feedback.
Audience
This documentation is intended for:
•Network planners.
•Field technical support and servicing engineers.
•Network administrators.
Conventions
The following information describes the conventions used in the documentation.
Command conventions
Convention Description
Boldface Bold text represents commands and keywords that you enter literally as shown.
Italic text represents arguments that you replace with actual values.
[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.
{ x | y | ... }
Braces enclose a set of required syntax choices separated by vertical bars, from which
you select one.
[ x | y | ... ]
Square brackets enclose a set of optional syntax choices separated by vertical bars,
from which you select one or none.
{ x | y | ... } *
Asterisk marked braces enclose a set of required syntax choices separated by vertical
bars, from which you select a minimum of one.
[ x | y | ... ] *
Asterisk marked square brackets enclose optional syntax choices separated by vertical
bars, from which you select one choice, multiple choices, or none.
&<1-n> The argument or keyword and argument combination before the ampersand (&) sign
can be entered 1 to n times.
# A line that starts with a pound (#) sign is comments.

GUI conventions
Convention Description
Boldface Window names, button names, field names, and menu items are in Boldface. For
example, the New User window opens; click OK.
> Multi-level menus are separated by angle brackets. For example, File > Create >
Folder.
Symbols
Convention Description
WARNING! An alert that calls attention to important information that if not understood or followed
can result in personal injury.
CAUTION: An alert that calls attention to important information that if not understood or followed
can result in data loss, data corruption, or damage to hardware or software.
IMPORTANT: An alert that calls attention to essential information.
NOTE: An alert that contains additional or supplementary information.
TIP: An alert that provides helpful information.
Network topology icons
Convention Description
Represents a generic network device, such as a router, switch, or firewall.
Represents a routing-capable device, such as a router or Layer 3 switch.
Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that
supports Layer 2 forwarding and other Layer 2 features.
Represents an access controller, a unified wired-WLAN module, or the access
controller engine on a unified wired-WLAN switch.
Represents an access point.
Represents a wireless terminator unit.
Represents a wireless terminator.
Represents a mesh access point.
Represents omnidirectional signals.
Represents directional signals.
Represents a security product, such as a firewall, UTM, multiservice security
gateway, or load balancing device.
T
T
T
T





Convention Description
Represents a security module, such as a firewall, load balancing, NetStream, SSL
VPN, IPS, or ACG module.
Examples provided in this document
Examples in this document might use devices that differ from your device in hardware model,
configuration, or software version. It is normal that the port numbers, sample output, screenshots,
and other information in the examples differ from what you have on your device.
Documentation feedback
You can e-mail your comments about product documentation to [e-mail].
We appreciate your comments.

i
Contents
IRF commands················································································1
display irf···························································································································1
display irf configuration·········································································································2
display irf link······················································································································3
display irf topology···············································································································4
display mad························································································································5
easy-irf······························································································································8
irf auto-update enable ········································································································10
irf domain ························································································································11
irf link-delay······················································································································11
irf mac-address·················································································································12
irf mac-address persistent···································································································13
irf member description········································································································14
irf member priority ·············································································································14
irf member renumber··········································································································15
irf-port·····························································································································16
irf-port-configuration active··································································································17
mad arp enable·················································································································18
mad bfd enable·················································································································19
mad enable······················································································································21
mad exclude interface ········································································································22
mad ip address·················································································································23
mad nd enable··················································································································24
mad restore······················································································································25
port group interface············································································································26
Index···························································································27

1
IRF commands
display irf
Use display irf to display IRF fabric information.
Syntax
display irf
Views
Any view
Predefined user roles
network-admin
network-operator
Examples
# Display IRF fabric information.
<Sysname> display irf
MemberID Role Priority CPU-Mac Description
1 Loading 1 00e0-fcbe-3102 F1Num001
*+2 Master 1 00e0-fcb1-ade2 F1Num002
--------------------------------------------------------
* indicates the device is the master.
+ indicates the device through which the user logs in.
The Bridge MAC of the IRF is: 00e0-fc00-1000
Auto upgrade : yes
Mac persistent : always
Domain ID : 30
Table 1 Command output
Field Description
MemberID IRF member ID:
•ID of the master is prefixed with an asterisk (*) sign.
•ID of the device where you are logged in is prefixed with a plus (+) sign.
Role
Role of the member device in the IRF fabric:
•Standby—Subordinate device.
•Master—Master device.
•Loading—The device is loading software images.
Priority IRF member priority.
CPU-MAC MAC address of the CPU in the device.

2
Field Description
Description
Description you have configured for the member device.
•If no description is configured, this field displays a dashed line (-----).
•If the description exceeds the maximum number of characters that can be
displayed, an ellipsis (…) is displayed in place of the exceeding text. To
display the complete description, use the display
current-configuration command.
Auto upgrade Status of the software auto-update feature:
•yes—Enabled.
•no—Disabled.
MAC persistent
IRF bridge MAC persistence setting:
•6 min—Bridge MAC address of the IRF fabric remains unchanged for 6
minutes after the address owner leaves.
•always—Bridge MAC address of the IRF fabric does not change after the
address owner leaves.
•no—Bridge MAC address of the current master replaces the original bridge
MAC address as soon as the owner of the original address leaves.
Domain ID Domain ID of the IRF fabric. The domain ID you assign to an IRF fabric must
uniquely identify the fabric in a multi-IRF fabric network.
Related commands
display irf configuration
display irf topology
display irf configuration
Use display irf configuration to display basic IRF settings for each member device.
Syntax
display irf configuration
Views
Any view
Predefined user roles
network-admin
network-operator
Examples
# Display basic IRF settings for all members.
<Sysname> display irf configuration
MemberID NewID IRF-Port1 IRF-Port2
1 1 Ten-GigabitEthernet2/0/5 Ten-GigabitEthernet1/0/6
2 2 Ten-GigabitEthernet2/0/5 Ten-GigabitEthernet2/0/6
Ten-GigabitEthernet2/0/7
Ten-GigabitEthernet2/0/8
4 4 Ten-GigabitEthernet4/0/5 Ten-GigabitEthernet4/0/6
Ten-GigabitEthernet4/0/7
Ten-GigabitEthernet4/0/8

3
Table 2 Command output
Field Description
MemberID Current member ID of the device.
NewID Member ID assigned to the device. This member ID takes effect at reboot.
IRF-Port1 Physical interfaces bound to IRF-port 1.
This field displays disable if no physical interfaces are bound to the IRF port.
IRF-Port2 Physical interfaces bound to IRF-port 2.
This field displays disable if no physical interfaces are bound to the IRF port.
Related commands
display irf
display irf topology
display irf link
Use display irf link to display IRF link information.
Syntax
display irf link
Views
Any view
Predefined user roles
network-admin
network-operator
Examples
# Display IRF link information.
<Sysname> display irf link
Member 1
IRF Port Interface Status
1 disable --
2 Ten-GigabitEthernet1/0/1 UP
Ten-GigabitEthernet1/0/2 ADM
Ten-GigabitEthernet1/0/3 DOWN
Member 2
IRF Port Interface Status
1 Ten-GigabitEthernet2/0/1 UP
Ten-GigabitEthernet2/0/2 DOWN
Ten-GigabitEthernet2/0/3 ADM
2 disable --
Table 3 Command output
Field Description
Member ID IRF member ID.

4
Field Description
IRF Port IRF port number:
•1—IRF-port 1.
•2—IRF-port 2.
Interface Physical interfaces bound to the IRF port. This field displays disable if no
physical interfaces have been bound to the IRF port.
Status
Link state of the IRF physical interface:
•UP—The link is up.
•DOWN—The link is down.
•ADM—The interface has been manually shut down by using the
shutdown command.
•ABSENT—Expansion interface card that hosts the interface is not
present.
display irf topology
Use display irf topology to display IRF fabric topology information.
Syntax
display irf topology
Views
Any view
Predefined user roles
network-admin
network-operator
Examples
# Display the IRF fabric topology.
<Sysname> display irf topology
Topology Info
-------------------------------------------------------------------------
IRF-Port1 IRF-Port2
MemberID Link neighbor Link neighbor Belong To
1 DOWN --- UP 2 000f-cbb8-1a82
2 UP 1 DIS --- 000f-cbb8-1a82
Table 4 Command output
Field Description
IRF-Port1 Information about IRF-port 1, including its link state and neighbor.
IRF-Port2 Information about IRF-port 2, including its link state and neighbor.
MemberID IRF member ID.