H3C S6800-4C Operating and maintenance manual

3
Installing the switch in a 19-inch rack安装交换机到19英寸机柜
Install cage nuts to the square holes on the rack posts
安装浮动螺母到机柜方孔条
Attach slide rails to the rack posts
安装滑道到机柜
Mount the switch in the rack (two options) 安装交换机到机柜（二选一）
Install cage nuts and slide rails 安装浮动螺母与滑道
Power module side mounting
挂耳安装在靠近电源侧
Port side mounting
挂耳安装在靠近端口侧
Connect the other end of the grounding
cable to the grounding point on the rack
接地线另一端连接到机柜接地点
Connect the other end of the grounding
cable to the grounding point on the rack
接地线另一端连接到机柜接地点
2
1
1
2
2
2
1
1
2
2
Connect the grounding cable to the grounding point on the chassis side before installing the switch
in the rack.
为了防止机箱安装到机柜后无法安装接地线，请您先将接地线安装到交换机的侧面接地点上。
The switch provides a grounding sign and grounding screws at the primary grounding point, but
does not provide them at the auxiliary grounding point.
主接地点标有接地标识，并带有接地螺钉，备用接地点无接地标识和接地螺钉。
The two grounding screws at the primary grounding point are also applicable to the auxiliary
grounding point. 主接地点上的两个接地螺钉同样适用于备用接地点。
Before installing cage nuts, mark their installation positions on the rack posts.
安装浮动螺母前，建议用户先使用记号笔在机柜立柱上标注浮动螺母安装位置。
4

5
Installing and removing a fan tray 风扇模块的安装与拆卸
Using the LSWM1BFANSC fan tray
采用LSWM1BFANSC风扇模块
Using the LSWM1BFANSCB fan tray
采用LSWM1BFANSCB风扇模块
6
Install a fan tray安装风扇 Remove a fan tray拆卸风扇
Installing and removing a power module 电源模块的安装与拆卸
Remove a power module拆卸电源模块
Install a power module安装电源模块
Remove a filler panel 拆卸假面板
Install a filler panel 安装假面板
Connecting the power cord 连接电源线
1
2
1
2
1
The LSWM1BFANSC fan tray provides forward airflow from the power module side to the port
side. The fan tray handles are blue. The LSWM1BFANSCB fan tray provides reverse airflow
from the port side to the power module side. The fan tray handles are red.
LSWM1BFANSC为吹风风扇，风向为电源侧进风，端口侧出风，风扇把手为蓝色LSWM1BFAN
SCB为抽风风扇，风向为端口侧进风，电源侧出风，风扇把手为红色。
Before installing a fan tray, make sure the airflow direction marked on the fan tray meets the
ventilation requirements at the installation site.
安装风扇模块前，请根据风扇模块的风向指示，确认气流方向和安装环境的通风要求一致。
When you install a fan tray, make sure the "TOP" mark is on the top surface of the fan tray.
安装风扇模块时，请确保“TOP”丝印朝上。
The switch comes with the fan tray slots empty. You must install two fan Trays of the same model
for the switch for adequate heat dissipation. Do not power on the switch when no fan tray is
installed.交换机出厂时两个风扇插槽均为空，为保证设备的正常散热，用户必须安装两个相同型号
的风扇模块，否则禁止交换机上电运行。
If both fan trays fail when the switch is operating, finish replacing the fan trays within 1 minute.
设备运行过程中，如果两个风扇模块均出现故障，则必须在1分钟内完成故障风扇模块的更换。
If one fan tray fails when the switch is operating and the ambient temperature is not higher than
27°C (80.6°F), replace the fan tray within 24 hours, and make sure the faulty fan tray is in position
before replacing it. If the ambient temperature is higher than 27°C (80.6°F), replace the fan tray
immediately. 设备运行过程中，如果一个风扇模块出现故障，则当环境温度不高于27℃时，必须在
24小时内完成故障风扇模块的更换，且更换前需保持故障风扇模块在位；当环境温度高于27℃时，
请立即进行更换。
Make sure each hot swappable module slot is installed with a module or filler panel when the
switch is operating.
设备运行过程中，必须确保所有可插拔模块插槽不能为空，请务必安装相应的模块或假面板。
!
Install a filler panel in an Empty power module slot to prevent dust from entering the chassis and
ensure good ventilation.若电源模块插槽没有安装电源模块，请及时安装假面板，以保证设备的良好
通风散热并防止灰尘进入交换机。
Before connecting the power cord, connect the grounding cable and make sure the switch is
reliably grounded. 在连接电源线前，需先连接保护地线，保证交换机正确接地。
Connect the power cord to the switch first and then to the power source to avoid bodily injury.
连接电源线时，请先完成电源线与交换机侧的连接，再进行电源线与供电系统的连接，以免造成人
身伤害。
!
Airflow through the switch 交换机的风向设计
The switch provides front-to-back and back-to-front air aisles. Select fan trays to provide airflow
from the power module side to the port side, or from the port side to the power module side based
on the ventilation requirements at the installation site.
交换机采用前后风道设计，通过安装不同的风扇模块，可提供“电源侧到端口侧”和“端口侧到电源侧”
两种气流方向，满足不同环境下的散热要求。

7
Connect the DC power cord 连接直流电源线 Connect the AC power cord 连接交流电源线
Installing and removing an interface card
接口模块扩展卡的安装与拆卸
Install an interface card安装接口模块扩展卡 Remove an interface card拆卸接口模块扩展卡
Use a removable cable tie to secure the power cord. The method for securing AC and DC power
cords are the same. The figures uses the AC power cord as an example.
使用可拆卸式扎带固定电源线，以防止电源线脱落；直流电源线和交流电源线的固定方式相同，此处以
交流电源线为例介绍电源线的固定过程。
12
1
221
3
Remove a filler panel 拆卸假面板Install a filler panel 安装假面板
To remove a filler panel:
1. Use your thumb and forefinger to hold the filler panel through the two holes.
2. Push right the metal tab in the left hole and pull out the filler panel along the guide rails.
拆卸假面板：用食指和拇指扣住假面板上的两个圆孔，向右用力按压左边圆孔内的金属弹片，然后沿插槽导
轨向外拉出假面板。
1
2
Do not touch the electronic components on an interface card to avoid damage.
请勿直接接触接口模块扩展卡上的元器件，避免造成损坏。
Install a filler panel to an empty interface card slot to prevent dust from entering the chassis and
ensure good ventilation.若接口模块扩展卡插槽没有安装接口模块扩展卡，请及时安装假面板，防
止灰尘进入交换机，同时又保证设备的良好通风散热。
Copyright © 2019, New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.
Copyright © 2019 新华三技术有限公司 版权所有，保留一切权利
本文档中的信息如有更改，恕不另行通知
如需了解产品及安装方面的更多信息，请登录H3C网站 www.h3c.com
!