Habitat BONNY BONNY-ST-AW17-A User manual

Assembly Instructions - Please keep for future reference
Important – Please read these instructions before assembly
BONNY SIDE TABLE
1
If you need help or have damaged or missing parts, email:
[email protected] or call: 0344 499 4686
BONNY-ST-AW17-A
Dimensions
Width – 46 cm
Depth – 46 cm
Height – 55.7 cm

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
If for any reason you should have
problems with your Habitat product,
please contact the store from which
you purchased it.
Please retain your receipt as proof of
purchase.
If you have any comments or
suggestions regarding this product,
assembly instructions or service
received, please contact the store or
Habitat Head Office via its web site:
www.habitat.co.uk
or write directly to: Habitat Retail Ltd.
489-499 Avebury Boulevard,
Milton Keynes MK9 2NW
General information
10 Kg
Check you have all the compo-
nents and tools listed on the
front cover and pages 2 - 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area,
small parts could choke if
swallowed.
Make sure you have enough
space to layout the parts
before starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close to
its final position (in the same
room) as possible.
Do not place furniture directly
in front of radiators, fires or
any other source of heat.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not recom-
mend the use of
power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Dispose of all packaging
carefully and responsibly.
Take care when moving furni-
ture - dragging it across the
floor will loosen and damage
the joints.
From time to time check that
there are no loose fittings.
Tighten as necessary.
Avoid exposing your furniture
to direct and prolonged periods
of sunlight and heat sources as
fading and cracking may occur.
Take care to prevent sharp
objects e.g. toys, buckles and
heels from coming into contact
with your furniture, and avoid
contact with chemicals e.g.
cosmetics or hair products
which may permanently mark
the surface.
Cleaning and care
Dust regularly with a clean dry
cloth.
Wipe up any spills immediately
with a damp cloth and then dry
the surface with a clean dry
duster.
Repeat this procedure for
periodic cleaning.
Remove stubborn stains with a
weak washing up liquid solu-
tion and a damp cloth and dry
after with a clean cloth.
The use of furniture polish or
spray is not necessary or
recommended.
Never use abrasive or corro-
sive cleaning agents.
Always use place mats and
coasters to protect the
surface from moisture and
heat.
1

Components - Panels
Please check you have all the panels listed below
BC Note: There are ‘Batch Code’ labels where shown onthe indicated items, these should be retained.
If you need help or have damaged ormissing parts, email:
[email protected] or call: 0344 499 4686
1PC
1
1PC
2
1PC
3
1PC
4
BC
1PC
5
2

Please check you have all the fixings listed belowNote
Components - Fittings
50.5 mm Screws x 1 PC
M4 Allen key x 1 PC
A B
Ruler- To help correctly identify the fixings
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120
105
Note: The quantities below are the correct amount to complete the assembly.
In some cases more fittings may be supplied than are required.
M6 Allen key x 1 PC
105 mm Pole x 1 PC
50 mm Spring washer x 2 PCS
9.5 mm Screws x 4 PCS
200 mm Screws x 1 PC
16.7 mm Screws x 1 PC
Dia.60 mm Th.2 mm Washer x 1 PC
C D
E F
G H
I
3

Assembly Instructions
Step 1
Step 2
A
E
x 1 PC
x 1 PC
4
A
E
2
3
I
Ix 1 PC

Assembly Instructions
Step 3
Step 4
Cx 1 PC
5
STOP
B
B
Bx 1 PC
3
C
C
4
B
B
3
4

6
1
G
G
F
I
D
5
E
D
H
Assembly Instructions
Step 5
Step 6
D
I
x 1 PC
x 1 PC
G
H
x 4 PCS
x 1 PC
Ex 1 PC
Fx 1 PC

Assembly Instructions
Step 7
7