Habitat Quint QUIN-1D-S13-A User manual

Quint
Quint Laptop Desk
204215
QUIN-1D-S13-A
1

Components
Please check you have all the parts listed below
Leg Frame Left Leg Frame Right
Body Crossbar
Worktop
Retain batch code label
BC
BC
2

Components -Fittings
Please check you have all the fittings listed below
Wooden dowel x12
Screws x3
Hex key x1 (4mm)
Cam bolt x12
Screws caps x1
Hex key x1 (3mm)
Cam lock x2
Connectors caps x2
Wall strap x1
Tools required
Before assembling the furniture please identify all component parts.
Keep children and animals away from the work area,small parts could choke if swallowed.
Assemble the item as close to its final position (in the same room) as possible.
Make sure you have enough space to layout the parts before starting.
Assemble on a soft level surface to avoid damaging the unit or your floor.
We do not recommend the use of power drill/drivers for inserting screws, as this could
damage the unit. Only use hand screwdrivers.
Dispose of all packaging carefully and responsibly.
IMPORTANT - PLEASE READ THESE INSTRUCTIONS FULLY BEFORE STARTING ASSEMBLY
3

Assembly Instructions
Please keep safe for future reference
Step 2
a: Insert wooden dowels
A into Body 3
b: Take the drawer out.
To do that pull it out
and lift it off the rails.
Step 1
a: Insert wooden dowels
A into Crossbar 4
b: Push cam locks C
into Crossbar 4
c: Screw cam bolts B
into Leg Frames 1 2
4

Step 3
a: Attach Body 3 to
Crossbar 4 with
screws D. To do this,
use hex key G .
b: Turn the table gently
onto the backside.
Assembly Instructions
Step 4
a: Attach Body and
Legs frames.
5

Assembly Instructions
Step 5
a: Tighten cam locks
(12 pieces) as shown
using hex key H
Step 6
a: Gently lift the table
on its legs.
b: Use the hex key
G to attach screw D
to the right side of
the table.
6
C

Assembley Instructions
Step 7
a: Attach Caps E , F
on the screws and
cam locks.
b: Put the drawer back
on the rails and close it.
Step 8
7
a: Align worktop 5 with
runners on body 3
and close .

Maintenance- To remove the Worktop
Step 1
a: Push spring clip
down with suitable
flat tools eg. ruler.
Step 3
a: Refit the worktop
as per step 8.
8
Step 2
a: Pull out the worktop
until the end, push 2
black nobs to the side
and pull it out.

It is recommended that the product is fitted with the anti-topple wall strap provided.
Warning!
The wall fixings are not supplied with this product. For fixing please seek the advice of a
professional builder.
Before you drill, check to ensure there are no hidden pipes or service cables in the wall.
9

Care instructions
Regular dusting with a dry cloth will keep your units clear.
Clean marks with a damp cloth.
Do not allow spillages to stay on the surface for long.
Do not use abrasive cleaners.
Do not clean with products containing the following:
Acetone, (e.g. nail varnish remover).
Ammonia (e.g.bleach). or Sodium hydroxide (e.g. Caustic soda, drain and oven cleaners).
Use place mats to protect the surface from moisture and heat.
If for any reason you should have problems
with your Habitat product, pleace contact the store
from which you purchased it.
Please retain your receipt as proof of purchase.
If you have any comments or
suggestions regarding this product, assembly instructions or
service, pleace contact the store or
Habitat Head Office via its web site:
www.habitat.co.uk
or write directly to:
Habitat Retail Ltd.
489-499 Avebury Boulevard,
Milton Keynes MK9 2NW
10