Habitat Verona 609/5095 User manual

Assembly Instructions - Please keep for future reference
Dimensions
Width - 60cm
Depth - 30cm
Height - 113cm
Important - Please read these instructions fully before starting assembly
issue 1 4/27/10
Verona Bookcase
609/5095
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
610/6472

We do not
recommend the use
of power drill/ drivers
for inserting screws,
as this could damage
the unit. Only use hand
screwdrivers.
Warning: The unit weighs
approximately 8.4kgs.
Please lift with care.
●Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
●From time to time check that
there are no loose screws on this
unit.
●This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
1
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
Check you have all the
components and tools listed on
pages 2 and 3.
plastic bags and separate them
into their groups.
Remove all fittings from the
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand on the panels, this
could cause damage.
Assemble the unit as close to its
final position (in the same room)
as possible.
Assemble on a soft level
surface to avoid damaging the unit
or your floor.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging carefully
and responsibly.

Components - Panels
Please check you have all the panels listed below
2
Leg x 12 (37.1 x Ø3.5cm)
2
Foot x 4 (4.7 x 3.4cm)Ø
3
Shelf x 3 (60 x 30cm)
1
Top shelf (60 x 30cm)
4
Cap screw x 4
Components - Fittings
Please check you have all the fittings listed below
Ruler - Use this ruler to help correctly identify the screws
A
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer Ruler/tape
measure
Tools required
Drill
7mm Masonary drill bit
(for use with wall plug)
Eye protection
(when using a
hammer or glue)
15mm Screw x 1
Wall strap x 1Wall plug x 1
B C
DE
27mm Screw x 1
Pre-assembled at 3
If you have damaged or missing components,
call the Customer Helpline:08456 400800

Assembly Instructions
Step 1
Fitting the legs
a:
3
A
Step 1
a: Unscrew Cap screws
a from the Feet .
b:
A3
b: Use Legs to fix the
Feet onto the Shelf
1 .
3
1
c: Use Legs to fix the
other Shelves onto
the unit.
c:
2
1
3
2
1
1
2
2
2
1
3

Assembly Instructions
Use Screw to fix the
Wall Strap onto the
underside of Top Shelf
1
Using a drill, predrill a
hole at the desired
height. Use the Wall
Plug to fit to the hole.
Pass Screw through
loose end of Wall Strap
to fix the unit into the
wall.
D
B
.
1
Use Cap screws to fix
the Top shelf on the
top of the unit.
Step 2
Finishing the unit
b:
4
A
A
4
ED
C
B
B
D
4
Important: When drilling
into walls always check
that there are no hidden
wires or pipes etc. Make
sure that the screws and
wall plugs supplied are
suitable for supporting the
unit. Consult a qualified
tradesperson if you are not
sure.
E
C
D
Assembly is complete.
4
Step 3
Fixing to wall
Note: It would be useful to
ask someone to help you
at this stage.
It is recommended that
the unit is fixed to a wall.
If you need help or have damaged or missing parts, call the Customer Helpline : 08456 400800

A Guide to -Wall Mounting & Fixings
Revision 2 - 7/10/09
Important note:
Types of walls
Care &
Maintenance
No.1 “General Purpose” wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
No.3 “Cavity Fixing” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist ftting in this case. For light
loads, general purpose wall plugs can
be used.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
For use with plasterboard partitions or
hollow wooden doors.
For use when ftting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with walls stuck with
plasterboard. The hammer fxing allows
it to be fxed to the wall rather than the
plasterboard. Always check the fxing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
Safety: Always check the ftting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the ftting to ensure the wall plugs
or screws do not become loose.
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well ftted and are a tight ft in the
drilled hole.
If plastic wall plugs
are supplied with your
product:
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualifed
tradesperson if you are unsure.
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fxings is the
responsibility of the installer.